Product data sheet OxyTrans I

Product catalog summary

Overview
The OxyTrans is a two-wire process oxygen analyzer designed for simple, accurate, and economical measurement of oxygen at trace and percentage levels. It features a straightforward display and one-point calibration for easy setup.

Specifications

Measuring Ranges: 0-10 ppm, 0-100 ppm, 0-1000 ppm, 0-10000 ppm, 0-25%, and 0-100% O2.
Calibration: Can be performed with calibration gas or air.
Accuracy: +/- 2% FSD at constant temperature, +/- 5% FSD from 0 to 50°C.
Resolution: 0.1 ppm for 0-100 ppm, 1 ppm for 0-1000 and 0-10000 ppm, 0.1% for percentage ranges.
Response Time: 90% FSD at 25°C, varying from 10 to 45 seconds depending on the range.
Operating Temperature: 0 - 50°C.
Pressure: 0.1 - 1 bar.
Signal Output: 4-20 mA/DC.
Alarm Value: Standard at 3.8 mA, optional at 23 mA.
Voltage: 10-35 VDC with reverse voltage protection up to 40VDC.
Load: Typically 470 Ohm, maximum 750 Ohm.
Display: 6-digit alphanumeric with bar graph.
Oxygen Sensor: Micro-Fuel Cell.
Housing: IP65 rated.
Size: 120 x 160 x 65 mm.
Weight: 1.2 kg.

Features

Compact and inexpensive design.
Long operating life of the sensor.
IP65 enclosure for protection.
Reverse voltage protection and temperature compensation.
Flow-through measuring cell made of stainless steel, allowing for modular repairs.

Applications
The OxyTrans is suitable for use in various industries, including semiconductor, gas manufacturing, metallurgical, chemical, heat treating, and bright annealing.

Optional Features
An optional sensor housing with a 1 ¼” thread is available for specific applications.

Catalog excerpts

OxyTrans 4 – 20 mA Loop Powered two wire Oxygen Transmitter Two Wire Process Oxygenanalyzer The Model OxyTrans is simple, accurate and economic measurement of Oxygen at trace and % levels. A simple Display and one point calibration allow easy and fast start-up of the instrument. optional ☺ One User specific measuring range The unit will offer with ranges between 0-10 ppm and 0 – 100% of oxygen. ☺ Sensor ☺ Flow-through measuring cell in Stainless Steel The OxyTrans uses a special fuel cell to measure the oxygen concentration. The sensor meets the industrial requirements for accuracy, sensitivity, easy to use and operating life. ☺ Calibration The calibration of the instrument for trace oxygen measurements in gas, should be done with a calibration gas. The concentration can be chosen freely within the measuring range. In the percent range the unit can calibrated with air. ☺ Features compact inexpensive Sensor with long operating life IP65 enclosure reverse voltage protection and temperature compensation The measuring cell is modular and is made of stainless steel A defective measuring cell can be repaired by replacing the defective part only, rather than th

Open the catalog to page 1

Response time Signal output Alarm value oxygen sensor Specification Measuring ranges : 10 - 35 VDC reverse voltage protection up to 40VDC : 6 Digits, alphanumeric with bar graph : Micro-Fuell Cell, ( uber alles ) • different sensors available • 5 different Measuring ranges • 316 SS Stainless steel Cell block optional Sensor housing with 1 W” Tread • Semi conductor industry • Metallurgical industries • Chemical industry • heat treating and bright annealing e-mail: [email protected]

Open the catalog to page 2

Product data sheet OxyTrans I

Product data sheet OxyTrans I

Catalog excerpts

All Pro-Chem-Analytik GmbH & Co. KG catalogs and technical brochures