2SIS0400T2C0C-33
10Pages

2SIS0400T2C0C-33 SCALE-iFlex Single Family Advanced Information Isolated Master Control Gate Driver for Half-Bridge Power Modules in high voltage package up to 3300 V Product Highlights Green Package Highly Integrated, Compact Footprint • Ready-to-use gate driver solution for power modules up to 3300 V blocking voltage • Electrical interface • Optimized for use with Module Adapted Gate Driver 2SMS0220D2C0C • -40 °C to +85 °C operating ambient temperature Protection / Safety Features • Undervoltage lock-out (UVLO) • Supporting Short-Circuit-Dection and Advanced Active Clamping of the Module Adapted Gate Driver • Applied double sided conformal coating Full Safety and Regulatory Compliance • 100% production partial discharge and HIPOT test of transformer • Clearance and creepage distances between primary and secondary sides meet requirements for reinforced isolation according to IEC 61800-5-1. • RoHS compliant Wind and photovoltaic power Traction inverter Industrial drives Other industrial applications Description This datasheet describes the Isolated Master Control (IMC) of the SCALE-iFlex™ Single gate driver family which consists furthermore of a Module Adapted Gate Driver (MAG). The IMC is designed for operation of power modules with a blocking voltage of up to 3300 V, whereas the MAGs are available in various variants optimized for different power modules of different suppliers and chip technologies in the voltage classes up to 3300 V. SCALE-iFlex Single enables compact and easy controlling power modules providing high flexibility and system scalability with minimum development effort. This Product is Covered by Patents and/or Pending Patent

Connector from IMC to external system controller. GND (Pin 1) This pin is the connection for the primary-side ground potential. Connector X1 Pin-header connector to MAG for gate driver channel 1 (high-side switch). VCC (Pin 2) This pin is the primary-side supply voltage connection and it has to be used for supplying the SCALE-iFlex Single gate driver. Connector X2 Pin-header connector to MAG for gate driver channel 2 (low-side switch). IN1 (Pin 6) This pin is the command input for channel 1 (high-side switch). NTC Connector Connector to module-internal NTC (directly routed to MAG). IN2 (Pin...

2SIS0400T2C0C-33 Functional Description The SCALE-iFlex Single is a dual channel gate driver, which consists of two parts: • Isolated Master Control (IMC) • Module Adapted Gate Driver (MAG) The IMC is independent of the actual target power module voltage class. It provides reinforced isolation of the power supply up to a voltage class of 3300 V. In contrast, the MAGs are particularly designed to operate specific power modules. Their characteristics match the requirements of the individual power modules. The interconnection between the external system controller to the IMC is established...

2SIS0400T2C0C-33 Outputs (X3) The gate driver provides status feedbacks SO1 and SO2. The status feedback signal stays at V VCC under no-fault condition. In case of a fault, e.g. detected short-circuit of the driven power module or an under voltage lock-out (UVLO) condition on the secondary-side, the status feedback is set to GND potential for a duration of tblk. In case of a primary-side UVLO condition both status feedback signals remain at GND during the UVLO and are extended by tblk. During this time no gate signals will be transmitted to the respective gate driver channel. Short-Circuit...

2SIS0400T2C0C-33 Maximum Ratings Parameter Absolute Maximum Ratings1 - 2SIS0400T2C0C-33 Primary-Side Supply Voltage Primary-Side Supply Current Logic Input Voltage Logic Output Voltage (Status Signal) Switching operation Transient only Gate Output Power Per Channel DC-Link Voltage Operating Voltage Primary-Side to Secondary-Side Switching Frequency Common-Mode-Transient Immunity Operating Ambient Temperature Relative Humidity Operation above this level requires a voltage derating to ensure proper isolation coordination. Recommended Operating Conditions Symbol Power Supply Primary-Side...

2SIS0400T2C0C-33 Electrical Characteristics - 2SIS0400T2C0C-33 Symbol Supply Current V VCC = 15 V, MAG connected, without load V VCC = 15 V, MAG connected, 100 nF load per channel, fSW = 25 kHz, 50 % duty cycle Turn-On Threshold Turn-Off Threshold Input Impedance Status Output Voltage Electrical Characteristics SOx to GND , ISOX < 0.5 mA, no-fault condition, internal 4.7 kΩ pull-up resistor is connected to VCC Clear fault (resume operation) UVLOVISOx Power Supply Monitoring Threshold (Secondary-Side) Set fault (suspend operation) Set fault (suspend operation) Referenced to respective...

Mounting Holes Diameter of screw holes Screw Header/Washer diameter Electrical Characteristics - 2SIS0400T2C0C-33 Test Voltage Partial Discharge Extinction Voltage Creepage Distance (on PCB) Clearance Distance NOTES: 1. Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. 2. The storage temperature inside the original package or in case the coating material of coated products may touch external parts must be limited to the given value. Otherwise, it is limited to 65 °C. 3. The component surface temperature, which may strongly vary depending...

PIHPAE_0089 Figure 5. Side View. Product Details Part Number Power Module Voltage Class Current Class Power Device Supplier Transportation and Storage Conditions For transportation and storage conditions refer to Power Integrations’ Application Note AN-1501. RoHS Statement We hereby confirm that the product supplied does not contain any of the restricted substances according Article 4 of the RoHS Directive 2011/65/EU in excess of the maximum concentration values tolerated by weight in any of their homogeneous materials. Additionally, the product complies with RoHS Directive 2015/863/EU...

This document contains information on a new product. Specifications and information herein are subject to change without notice.