PW636i-F Digital Relay Test Kit
21Pages

PW636i‐F Digital Relay Test Kit PONOVO POWER CO., LTD. www.

PW636i‐F Digital Relay Test Kit PW636i‐F (6×32A, 4×300V, 8 fiber optic ports) is the new generation of PW series relay test set which can be used both as a conventional relay test kit and IEC61850 testing tools. Other test works, such as transducer, energy meter, indication meter, etc., can also be done easily. It's the ideal test device for all power utilities, power plants, relay manufactures, panel manufactures, research institutes, universities, testing companies, etc. Product Features  In‐built monitoring and recording  Large output power  Support GOOSE/SV based test  Current...

PW636i‐F Digital Relay Test Kit PW636i‐F is not only has current and voltage outputs for all kinds of conventional relay testings, but also has 8 switchable optical fiber/Ethernet ports to support digital relay protection tests based on IEC61850. It can send and receive SV, simulate MU to send SV to relay which the dispersion is better than ±80ns, receive SV, realizing self‐loop test. It can publish and subscribe GOOSE message, many different kinds control/block messages, simulate the abnormal message (jitter, frame loss, flying spot, wrong sequence, data anomalies, packet retransmission,...

PW636i‐F Digital Relay Test Kit PW636i‐F is designed with fuse on the mains supply and electronic protection for overload on the current (open circuit) or voltage outputs (short circuit), with immediate isolation of the output and alarm indication. Also diagnostic message for the setting of wrong data, mistakes on the input etc. There’s also electronic protection in case of counter‐ feed of voltage output, if any incorrectness happens, the alarm light shall flash. And Overheat LED indicator shall flash for protection against over‐temperature, on all outputs. GPS Antenna connection Port 8...

PW636i‐F Digital Relay Test Kit Binary input group 1 Binary output group 2 External amplifier, low level output and binary input group 2 Ventilation Power switch Mains supply connector IP Reset GPS interface Test functions according to IEEE relay code IEEE. NO. DEVICE 2 21 24 25 Time Delay Starting or Closing Relay Distance Relay Volts per Hertz Relay Synchronizing or Synchronism‐Check Device 27/27N Undervoltage Relay 30 Annunciator Relay 32 Directional Power Relay 36 Polarity or Polarizing Voltage Devices 37 Undercurrent or Underpower Relay 40 Field (over/under excitation) Relay 46 Reverse...

PowerTest For PW636i-F Digital Relay Test Kit Software PowerTest For PW636i-F is specially designed for PW636i-F digital relay test kit. The application equipment includes intelligent equipment (merging unit, protection relays and intelligent terminals, etc.) and power system automatic equipment. PowerTest For PW636i-F is a relay test software that includes different test packages, the Basic package, Protection package, Advanced package, Special package, IEC61850 package, New Modules, which packages includes different testing module, that can be used for all kinds of relay testing, and it...

QuickTest (Advanced)  12 voltage and 12 current sources available for test relay  Amplitude and phase angle of voltage and current sources can be controlled independently  Test can be in manual or auto mode  Easy to control the phase‐phase voltage, 3V0 (zero sequence voltage) and 3 currents  Amplitude, phase angle and frequency of current sources and phase‐phase voltage, zero sequence voltage can be controlled independently  Test can be in manual or auto mode QuickTest (Sequence)  Easy to control the sequence components (positive sequence, negative sequence and zero sequence) for...

 Easy to test impedance relay with constant voltage  Set the fault impedance and fault voltage, obtain the amplitude and phase angle of each phase voltage and current according to the fault type  Can manually or automatic search the relay operation value QuickTest (Z, Zs Const)  Easy to test impedance relay with constant system impedance  Set the fault impedance and system impedance, obtain the amplitude and phase angle of each phase voltage and current according to the fault type  Can manually or automatic search the relay operation value Time  Time module is used to test trip delay...

 Can generate harmonics for all voltage and current outputs  Can check the 2nd /3rd / 4th /5th harmonic restraint of current differential  Can check the harmonic measurement of the relay up to 31st harmonic  Can set the harmonic for each channel separately CB Operate  Can check different types of line protection system, including over current, distance, etc.  Can check the whole relay system, including auto‐reclosing and circuit breaker simulate  Can set different fault type  Can do end‐to‐end test with GPS control mode  Protection Package In protection package, there are more...

Can test impedance relay with R‐X setting in different ways Input impedance characteristic to Z plain Associate the characteristic with relay settings Select test point directly on Z plain or in setting box Zone verification Z‐T test Edit new characteristic Distance (Z-Phi)  Can test impedance relay with Z‐Phi setting in different ways  Input impedance characteristic to Z plain  Associate the characteristic with relay settings  Select test point directly on Z plain or in setting box  Zone verification  Z‐T test  Edit new characteristic Directional  Can test maximum trip angle and...

Time Inversed Current  Used to test time inversed current relay  Can test normal current relay with or without time delay  Can test directional current relay with or without time delay  Can test the inversed current relay with user defined curve  Can import the IEC and IEEE standard curve Time Inversed Voltage  Used to test time inversed voltage relay  Include testing directional, time definite and with time delay voltage relay  Can simulate three phase, phase‐earth fault, and phase‐phase fault Frequency Relay  Can test frequency protection relay, such as over frequency, under...