SPINWORX ®
28Pages

Time-saving tooling system for reduced manning operation with self-rotating inserts

 Spinworx®  spinworx®  Copy milling cutters  milling cutter bodies THE UNIQUE TIME-SAVING TOOLING SYSTEM for reduced manning operation WITH SELF-ROTATING INSERTS PINWORX® – the innovative tooling system puts into and optimise your machine availability at the same time. question what has been an effective operation for deca- SPINWORX® tools are ideal for roughing and residual material des: the insert has to be „rigidly“ coupled to the cutter body machining during the face milling, slot, peripheral and pocket – if it were „loose“ in its insert seat it would break soon-er milling of...

100% use of the total insert periphery Can be used in steel, cast iron, stainless steel and high-temperature alloys Minimised set-up times since no manual re-locating of the inserts is necessary Ideal for roughing and residual material machining during face milling, slot, peripheral and pocket milling Multiple increase in tool life* Chip volume is much higher without interruption in the production process* Reduced chip compression leads to lower power consumption, which also protects your machine spindle * depending on milling conditions Insert seat: The large transition radius of the seats...

 Spinworx®  spinworx®  Copy milling cutters  milling cutter bodies GOES ON AND ON AND ON ... THE SELF-ROTATING INSERT crucial component in the SPINWORX® tooling system are the self-rotating inserts, which have been optimally matched to the milling cutter seats of course. And it‘s the special design features which make safe and long-term function possible here, too. There are cutting materials with and without chip groove and different cutting edge geometries available. Every single insert is delivered with an exactly matching pin. Order number key: SPINWORX® Inserts The pin/insert...

Simple assignment of tool and insert Practical Video DR 10 - 025-E12-03 DR 10 - 8C7 - P Insert size can be recognised directly, straightforward assignment Prefixing group key for the fast assignment of tool type and insert Simple fitting of the inserts in the tool Step 1: Place the inserts (1) into the seat provided. Apply the paste included (4) to the thread of the pin (2) and make sure no paste (catalogue number „Z 00043“) gets onto the contact surface. Remove any surplus before using the tool. Tool: Insert: Spinworx® in 1.2738: Tool life13 hours, P20 / 40CrMnNiMo8-6-4 Step 2: Insert the...

 spinworx®  Copy milling cutters  milling cutter bodies SPINWORX® r3.5 - diam. 16 - 35 mm, 7° positive rake angle The SPINWORX system in its smallest version • effective use of cutting edge and machining of smaller workpieces • wide range of use for almost all areas of application • effective use of the cutting edge • with specially adapted coolant supply • low power consumption, high chip removal rate CAUTION - PLEASE NOTE! For optimum results with the SPINWORX®-tooling system we recommend using internal coolant supply air, emulsion or MQL for chip removal from the tool! Wet machining...

Indexable inserts Feed per tooth (fz) | d.o.c. (ap) Material Quality Coating major application minor application

 SPINWORX®  Copy milling cutters spinworx®  milling cutter bodies Cutting speed (Vc in m/min) Material Quality Coating roughing pre finishing finishing roughing pre finishing finishing roughing pre finishing finishing roughing pre finishing finishing roughing pre finishing finishing roughing pre finishing finishing roughing pre finishing finishing roughing pre finishing finishing roughing pre finishing finishing roughing pre finishing finishing roughing pre finishing finishing roughing pre finishing finishing roughing pre finishing finishing roughing pre finishing finishing

Extended operation data Plunging minor application major application

 spinworx®  Copy milling cutters  milling cutter bodies SPINWORX ® IN PRACTIC AL TEST S – CONVINCING RESULTS Material to be machined: 1.2312 Wear patterns on insert DR07-8E4 Insert Coating Vf feed rate [mm/min] Stock removal rate [cm3/min] Uninterrupted machine running time of 579 minutes - and the inserts wear limit was not yet reached. This process reliability without any cutting edge break-out speaks for itself and for SPINWORX®. Wear patterns on insert DR07-8D3 Insert Coating Vf feed rate [mm/min] Stock removal rate [cm /min] 3 Process-reliable machining of titanium alloy for the...

SPINWORX® r5 - diam. 20 - 52 mm, 7° positive rake angle The all-rounders in the SPINWORX series. • wide range of use for almost all areas of application • effective use of the cutting edge • with specially adapted primary and secondary coolant supply • low power consumption, high chip removal rate CAUTION! PLEASE NOTE! For optimum results with the SPINWORX®-tooling system we recommend using internal coolant supply air, emulsion or MQL for chip removal in the tool! Wet machining up to max speed Vc of 140 m/min! Milling cutter bodies Threaded shank end mill bodies Shell-type milling cutter...

 SPINWORX®  Copy milling cutters spinworx®  milling cutter bodies Indexable inserts Feed per tooth (fz) | d.o.c. (ap) Material Quality Coating available as long as stock lasts 12 stock item, subjec

Cutting speed (Vc in m/min) Material Quality Coating roughing pre finishing finishing roughing pre finishing finishing roughing pre finishing finishing roughing pre finishing finishing roughing pre finishing finishing roughing pre finishing finishing roughing pre finishing finishing roughing pre finishing finishing roughing pre finishing finishing roughing pre finishing finishing roughing pre finishing finishing roughing pre finishing finishing roughing pre finishing finishing minor application major application

 spinworx®  Copy milling cutters  milling cutter bodies Extended operation data Plunging