TETRIS®1000 / 1500 High Impedance Active Probe Order-No: 881-000-000 881-500-000 Features:  High Input Impedance  Interchangeable Spring Tips  Contacts adjacent Pins in 2.54 mm Pitch  Useable with any 50 Ω Measuring Instrument The TETRIS® active probe is a manufacturer independent measurement system, which can be used with any oscilloscope having 50 Ω input. Its small size and useful accessories are designed to make any measuring task easy. System- dependency is known to be an issue in many work places and laboratories, not only concerning measurement instruments and accessories. With a standalone power supply and relying on 50 Ω input only, PMK probes are independent from the measuring instruments as such. The small housing and the distinctive T-shape of the TETRIS® probe head make contacts in 2.54 mm pitches especially easy, as multiple TETRIS®'s probes can contact adjacent pins simultaneously. Connections to smaller parts are achieved either by an IC contacting system or famous clamps also available at PMK and partly enclosed in the standard scope of delivery. The choice for an active probe instead of a low-Z passive one is simple, because passive probes, with their relatively high input capacitance, load the signal source already at frequencies above 100 kHz. The TETRIS® active probe offers high input impedance into the GHz-range. Two of the three TETRIS® models are subject of this Datasheet. Find additional information on TETRIS® 2500 under Ord.-No: 882-500-000 or contact our sales department. Order No: 881-000-000 / 881-500-00

This datasheet supersedes all previously published material. Specifications that are not marked as guaranteed are published as general information to the user. The instrument should have warmed up for at least 20 minutes and the environmental conditions must not exceed the specified limits of the probe. Note that specifications are subject to change without notice. Model Attenuation Ratio Voltage Coefficient Input Voltage (max) Probe Bandwidth System Bandwidth (1) Input Dynamic Range Maximum Input Voltage and Dynamic Range The TETRIS® Active Probe is secured against static overvoltage. Applying...

Typical InputInput Impedance TETRIS® 10001500 Typical Impedance TETRIS® 1000 / / 1500 1M Ersatzschaltbild Tastkopf Note that the Input Impedance of the Probe decreases as the C1= 1,0Frequency 3of the Applied Signal nF R1= MΩ C2= 0,88 pF R2= increases. 1 MΩ Electrical Characteristics Input Resistance (system) Input Capacitance (system) Input Coupling of the Measuring Instrument Mechanical Characteristics Weight (probe only) Cable Length

Environmental Specifications Altitude Temperature Range Maximum Relative Humidity operating non-operating operating non-operating operating up to 2000 m up to 15000 m 0 °C to +50 °C -40 °C to +71 °C 80% relative humidity for temperatures up to +31 °C, decreasing linearly to 40 % at +50 °C Accessories for TETRIS® Active Probes Tetris Active Probes support a vast number of accessories. From different Tips & Pins over Leads and Adapters to popular Clips you might know from other applications. Most of them are found in the standard scope of delivery marked (x) in the table below. Differing in quantity...

Accessories for TETRIS®®Active Probes Accessories for TETRIS Active Probes 890-100-150 10 self-adhesive Cu-Pads (2x2 cm) 890-020-916 Marker Bands 4x4 Colors 890-8 800-001 890-800-001 Set 5 Sp pring Spring Tips 890-502-130 QFP IC-Clips long to 0.5 mm pitch (1 pair yellow/green) 890-720-800 Y-Lead Adapter to 0.8 mm Sockets 10 cm 890-502-000 QFP IC-Clips short to 0.5 mm pitch (1 pair yellow/green) 890-720-816 Y-Lead Adapter to open Leads 6 cm 890-400-803 Gro ound Ground Lead 90° 5 cm 890-720-813 Y-Lead Adapter to open Leads 3 cm

TETRIS®1000 / 1500Datasheet WEEE/ RoHS Directives PMK electronic products are classified within the WEEE/ RoHS* category list as monitoring and control equipment (category 9). Category 9 products are exempt from the restrictions under the scope of the RoHS directive. Your help and efforts are required to protect and keep clean our environment. Therefore return any electronic product at the end of its life either to Service Department of PMK Mess- und Kommunikationstechnik GmbH or take care of separate WEEE collection and professional WEEE treatment yourself. Do not dispose as unsorted municipal...