Automotive Accessories catalogue
12Pages

Oscilloscope Diagnostics

Whether you’RE a busy workshop, automotive technician or vehicle manufacturer, our vehicle diagnostics equipment will help you to save time and money. The Pico Automotive Diagnostics Kit turns your laptop or desktop PC into a powerful automotive diagnostic tool for fault-finding the increasing number of sensors, actuators and electronic circuits found on today’s vehicles. Pico Technology offers a range of kits 2-CHANNEL STARTER KIT 4-CHANNEL STARTER KIT 2-CHANNEL PicoScope 4223 oscilloscope, 1 x black TA005 & 1 x red TA006 dolphin clips Premium test lead: BNC to 4mm blue TA125 (fixed...

Our award-winning automotive oscilloscopes work with any bike, car or truck and make it easier — and faster — for you to find faults, SAVING YOU AND YOUR CUSTOMERS TIME AND MONEY The automotive kit is based around the highly successful range of PicoScope automotive diagnostic oscilloscopes. These high resolution PC oscilloscopes connect to a USB port on your PC and can take up to 32 million samples per trace, making it possible to 4-CHANNEL ADVANCED KIT Contains all the items in the 4-channel standard kit, plus: Extra 60 A current clamp TA018 2 x Fuse extension leads PP408 Coil-on-plug...

PICKED YOUR KIT? NOW MAKE SURE YOU HAVE THE RIGHT ACCESSORIES TO GO WITH IT… The Pico range of automotive accessories is ideal for use with PicoScope automotive diagnostics kits, automotive oscilloscopes and other labscopes. Over the next few pages you will find a full list of all the accessories we offer. The items that are included in the six kits have a colour coded circle next to them to indicate this. 2-Channel Starter kit 4-Channel Starter kit Standard kits 4 Channel advanced kit Commercial vehicle kit 60 A CURRENT CLAMP The 60 A current clamp allows you to measure current up to 60...

SECONDARY IGNITION PICKUP The secondary ignition pickup enables the PicoScope to measure high-tension (HT) voltages in secondary ignition circuits. It clips onto the HT lead with no need to disconnect the lead. The lead includes a ground clip that you must always connect to battery negative (earth) to prevent stray voltages from damaging the PicoScope. The Coil-on-Plug (COP) probe can pick up secondary ignition waveforms from most coil-on-plug or coil-per-cylinder systems where there are no exposed HT leads. The signal is displayed in PicoScope as kilovolts (kVs). BNC to BNC cable with...

SMALL CROCODILE CLIPS The acupuncture probes slide under the insulation of multi-plug terminals from behind the plug, allowing you to pick up signals without stripping wires or disconnecting plugs. This technique is sometimes called back-pinning. Each probe fits onto the 4-mm plug of our BNC to 4mm test leads. A storage box containing spare pins and screws is included. MULTIMETER PROBES These probes fit all our BNC-to-4-mm test leads. They are used to make contact with exposed wires and terminals These clips fit all our BNC-to-4-mm test leads. They are used to make contact with exposed...

60 MHZ OSCILLOSCOPE PROBE This 60 MHz oscilloscope probe is used for accurately measuring fast signals like CAN bus and FlexRay. Standard BNC plug 1.2m long. 60 MHz oscilloscope probe MI007 £15 $24.75 ¤18.15 DIFFERENTIAL PROBE The active differential probes lets you measure higher voltage and are ideal for hybrid and electric vehicles. These probes have a bandwidth of 25 MHz, with differential voltage ranges of 700V or 1400V. 700V differential probe TA041 £195 321.75 ¤235.95 1400V differential probe TA057 £220 $363 ¤266.20 4 MM SHROUDED TO UNSHROUDED ADAPTORS Converts the shrouded 4-mm...

6-WAY UNIVERSAL BREAKOUT LEADS BASIC BNC TO 4 MM TEST LEAD No need to pierce insulation or back-pin connectors. Fully shrouded and insulated for safety. These breakout leads simply connect into the existing cable loom and enable voltage readings to be taken from numerous sensors in the engine compartment FUSE EXTENSION LEADS ATS and mini-ATS sizes for common fuses. Use with the 60 amp clamp to measure fuse current. For standard 2-pin sensors and actuators. With 4mm plugs to connect to PicoScope test leads. CABLES & LEADS Custom-made for automotive diagnostics. 3m and 5m long versions...

CAN TEST BOX The CAN Test Box allows you to connect your PicoScope oscilloscope to the 16 pin diagnostic connector enabling you to monitor any signals present, such as the CAN High and Low signals. The CAN Test Box terminal pin ports are accessible with standard 4 mm plugs. The CAN Test Box uses numbered backlit LEDs which illuminate when signal data is present on the corresponding pin of the Data Link Connector (subject to the vehicle manufacturer’s specification). Pulsing LEDs indicate signals alternating high and low. The CAN Test Box is fitted with a 2.5 metre (8.2 feet) cable so that...

With the uncompromising resolution and accuracy of the WPS500X automotive pressure transducer you can perform quick and accurate pressure analysis of many automotive systems. Ultra-fast 100 us response time Zoom function for enhanced analysis capabilities Rechargeable LiPo battery Integrated pressure relief / bleed-off valve Auto zeroing High noise immunity Temperature compensated The WPS5000X features an extremely fast 100 us response rate from 0% to 90% of full scale and sensitivity down to about 0.07 psi (5 mbar). This provides you with an accurate representation of rapidly changing...

FUEL HOSES Enables connection to fuel systems with WPS500X See vehicle manufacture data sheets. Fuel hose with large Schrader valve TA083 £20 $33 €24.20 Fuel hose with small Schrader valve TA117 £20 $33 €24.20 HIGH STRENGTH COMPRESSION HOSES These specially designed compression hoses allow the WPS500X to be used for high pressure tests such as cranking and running cylinder compression or fuel pressure testing. Use to investigate compression issues, blocked catalytic converters, restricted air intakes and many other problems such as cam timing and valve issues. Ford Triton compression hose...