Catalogs >
Pico Electronics >
Series LP

Series LP
1 / 13Pages

Catalog excerpts

PRODUCT OVERVIEW The LP series are isolated DC-DC converters with a wide selection of input voltage ranges from 18V to 380V in a compact half brick size foot print - 2.4" x 2.3". These modules have trim capability and shutdown features. Protections include input overvoltage, output short-circuit, output overvoltage and over temperature. The unique case has integrated side heat sink for better thermal dissipation but is capable of conduction cooling through the baseplate or additional top mounted heat sink. FEATURES • 18V to 380V input range models • Input/output isolation • Integrated side heat sink • Parallel operation option • Single and dual isolated outputs • Trim capability • Remote shutdown feature • Fixed operating frequency • No external components required Contact Pico for part number of available options: Stabilization Bake Temperature Cycle Burn-In • Special Input Voltage, Output Voltage, Isolation Voltage or Output Power • Parallel Operation

Open the catalog to page 1

Series LP High Power DC-DCMODEL LIST - LPA (18-36V INPUT RANGE)SINGLE OUTPUT Pico Part Note 1: Maintain minimum 10% of rated load to prevent a voltage surge. Note 2: Tested at nominal input voltage and full output load. Note 3: For <100V output models, load regulation is specified for 10-100% load. For >125V output models, load regulation is specified for 20100% load. Note 4: Dual output loads must be balanced.

Open the catalog to page 2

Series LP High Power DC-DCMODEL LIST - LPB (36-72V INPUT RANGE)SINGLE OUTPUT Pico Part Note 1: Maintain minimum 10% of rated load to prevent a voltage surge. Note 2: Tested at nominal input voltage and full output load. Note 3: For <100V output models, load regulation is specified for 10-100% load. For >125V output models, load regulation is specified for 20100% load. Note 4: Dual output loads must be balanced.

Open the catalog to page 3

Series LP High Power DC-DCMODEL LIST - LPC (100-180V INPUT RANGE)SINGLE OUTPUT Pico Part Note 1: Maintain minimum 10% of rated load to prevent a voltage surge. Note 2: Tested at nominal input voltage and full output load. Note 3: For <100V output models, load regulation is specified for 10-100% load. For >125V output models, load regulation is specified for 20100% load. Note 4: Dual output loads must be balanced.

Open the catalog to page 4

Series LP High Power DC-DCMODEL LIST - LPD (200-380V INPUT RANGE)SINGLE OUTPUT Pico Part Note 1: Maintain minimum 10% of rated load to prevent a voltage surge. Note 2: Tested at nominal input voltage and full output load. Note 3: For <100V output models, load regulation is specified for 10-100% load. For >125V output models, load regulation is specified for 20100% load. Note 4: Dual output loads must be balanced.

Open the catalog to page 5

Series LP High Power DC-DCSPECIFICATIONS (Nominal VIN, Full Load, TA = +25°C, 1 hour warm up unless otherwise specified) INPUT Note 3: The parallel option allows units to operate the outputs in parallel to share load, increase total power or allow for N+1 redundancy.

Open the catalog to page 6

Series LP High Power DC-DCSPECIFICATIONS (Nominal VIN, Full Load, TA = +25°C, 1 hour warm up unless otherwise specified) DESIGNED TO MEET DERATING GRAPHS (Nominal VIN, Full Load, Efficiency @ Full Load) Models with Max. Output Power = 75W & Efficiency at full load = 87% Models with Max. Output Power = 75W & Efficiency at full load = 86%

Open the catalog to page 7

TYPICAL CONNECTION CIRCUIT TRIM TRIM UP TRIM DOWN TRIM DOWN TRIM DOWN, TRIM Note: Each individual unit will vary slightly. It is recommended to use a 1MO multi-turn trimmer potentiometer to determine resistance value and achieve desired adjustment. Use minimum 1/2W power rating resistor. Keep the trim resistor leads as short as possible to eliminate the stray inductance which will effect the trimming results.

Open the catalog to page 8

Series LP High Power DC-DCTYPICAL CONNECTION CIRCUIT NOISE REDUCTION Note 4: C1 filter capacitors may reduce noise further. Please contact Pico for more details.

Open the catalog to page 9

Series LP High Power DC-DC MECHANICAL DRAWINGS LTI - THERMAL INTERFACE .002 [.051] BOTTOM VIEW Material Alloy Aluminum Substrate Thermal Conductivity Coefficient of Thermal Expansion, (25-100°C) Brinell Hardness Endurance Limit Standard Thickness Weight: 70 grams typical 2025 REV 0

Open the catalog to page 11

Series LP High Power DC-DC TUBE PACKAGING TUBE PACKAGE TUBE PLUG TUBE PLUG POWER SUPPLY Pico warrants each product manufactured by us and sold by us or an authorized representative, to be free from defects in material and workmanship. If properly used, it will perform within its applicable specifications for a period of one year after original shipment. Pico’s obligation under this guarantee is limited to repairing or replacing our product to the original purchaser. This warranty is in lieu of all other warranties, express or implied and constitutes fulfillment of our obligations to the...

Open the catalog to page 13