The AV & SMV series are unregulated DC-DC converters in a low profile package, down to 0.400", footprint with up to 1000V single or dual output models. They can operate over the temperature range of -25°C to +70°C without derating, a heat sink or active cooling. • 1.25W output power Contact Pico for part number of available options: • Output voltage is directly proportional to input voltage • Through hole or surface mount mounting available • Input/output isolation • Single and dual output models • No heat sink or derating required Expanded operating temp: -55°C to +85°C Select screening per MIL-STD-883: Stabilization Bake Temperature Cycle Burn-In Available RoHS Compliant module Special Input Voltage, Output Voltage, Isolation Voltage or Output Power Tighter Output Voltage Tolerance 100V BLANK = SINGLE OUTPUT

Note 1: Maintain minimum 10% of rated load on each output to prevent a voltage surge. Note 2: For <500V output models, a 0.1|_iF, 1kV capacitor is required across the output. For >600V output models, a 0.01|_iF, 3kV capacitor is required across output. Note 3: Tested at nominal input voltage and full output load.

Note 1: Maintain minimum 10% of rated load on each output to prevent a voltage surge. Note 3: Tested at nominal input voltage and full output load. Note 4: 0.1|_iF, 1kV high quality capacitor is required across each output.

Input Voltage Range

Series AV & SMV (100-1kV) High Voltage DC-DC SPECIFICATIONS (Nominal VIN, Full Load, TA = +25°C, 1 hour warm up unless otherwise specified) OPTIONS AVAILABLE – CONTACT PICO FOR PART NUMBER Parameter Referenced Standard Stabilization Bake Referenced Method 1008 Non-operating maximum storage temperature for 24 hours Temperature Cycle Referenced Method 1010 Non-operating at temperature extremes, 15 mins/temp, 10 cycles Referenced Method 1015 Max operating temperature for 160 hours OPTIONS AVAILABLE Expanded Ambient Operating Temperature RoHS Compliance DATA CURVES (Nominal VIN, TA = +25°C, 1 hour...

Series AV & SMV (100-1kV) High Voltage DC-DC TYPICAL CONNECTION CIRCUIT SINGLE OUTPUTS Note 2: For ≤500V output models, a 0.1µF, 1kV capacitor is required across the output. For ≥600V output models, a 0.01µF, 3kV capacitor is required across output. DUAL OUTPUTS Note 4: 0.1µF, 1kV high quality capacitor is required across each output. Safety Note: The high voltage power supplies described in this datasheet generate voltages which can be lethal. They should only be installed and used by personnel who have received the appropriate training and who are fully aware of the hazards that exist. 2025...

Series AV & SMV (100-1kV) High Voltage DC-DC MECHANICAL DRAWINGS SERIES AV - THROUGH HOLE SINGLE ≥600V OUTPUTS BOTTOM VIEW BOTTOM VIEW NOTES a. ALL DIMENSIONS ARE IN INCHES, [ ] = MM b. WHITE DOT ON TOP SIDE INDICATES +IN LOCATION 2025 REV 0 BOTTOM VIEW

Series AV & SMV (100-1kV) High Voltage DC-DC MECHANICAL DRAWINGS SERIES SM - SURFACE MOUNT SINGLE ≥600V OUTPUTS BOTTOM VIEW BOTTOM VIEW DUAL OUTPUTS LEAD DETAILS BOTTOM VIEW NOTES a. ALL DIMENSIONS ARE IN INCHES, [ ] = MM b. WHITE DOT ON TOP SIDE INDICATES +IN LOCATION 2025 REV 0

Series AV & SMV (100-1kV) High Voltage DC-DC RECOMMENDED LAND PATTERN DIMENSIONS SERIES SMV - SINGLE OUTPUTS .130 [3.302] SERIES SMV - DUAL OUTPUTS .130 [3.302] TUBE PACKAGING SERIES AV - THROUGH HOLE .600 [15.240] TUBE PLUG POWER SUPPLY

Series AV & SMV (100-1kV) High Voltage DC-DC TUBE PACKAGING SERIES SMV - SURFACE MOUNT, ≤500V OUTPUTS 20.000 [508.000] PLAN VIEW ELEVATION VIEW SERIES SMV - SURFACE MOUNT, ≥600V OUTPUTS .584 [14.824] PLAN VIEW SEALED ELEVATION VIEW UNSEALED TUBE PACKAGE TUBE PLUG TUBE PLUG POWER SUPPLY Pico warrants each product manufactured by us and sold by us or an authorized representative, to be free from defects in material and workmanship. If properly used, it will perform within its applicable specifications for a period of one year after original shipment. Pico’s obligation under this guarantee is limited...