AXL F SSDOR4/2 1F Axioline F safety module with safe relay outputs Original operating instructions

Original operating instructions AXL F SSDOR4/2 1F Axioline F safety module with safe relay outputs 2022-04-29 UM EN AXL F PSDOR4/2 1F, Revision 02 This user manual is valid for: Designation PHOENIX CONTACT GmbH & Co. KG • Flachsmarktstraße 8 • 32825 Blomberg • Germany phoenixcontact

PHOENIX CONTACT

PHOENIX CONTACT

For your safety Read this user manual carefully and keep it for future reference. Identification of warning notes This symbol indicates hazards that could lead to personal injury. There are three signal words indicating the severity of a potential injury. DANGER Indicates a hazard with a high risk level. If this hazardous situation is not avoided, it will result in death or serious injury. WARNING Indicates a hazard with a medium risk level. If this hazardous situation is not avoided, it could result in death or serious injury. CAUTION Indicates a hazard with a low risk level. If this hazardous...

Field of application of the product Intended use The AXL F SSDOR4/2 1F safety module is designed for use in a SafetyBridge system. To this end, the safety module is integrated into the Axioline F system. The safety module is designed for the connection of: – Suitable 1 or 2-channel actuators Safety functions The safety module performs the following safety functions: – Safe interruption of circuits – Safe transmission of I/O signals Safe shutdown The intended use for the safety module is safe switch-off. Safe switch-on does not fall under the intended use.  See “Safe state” on page 29. The safety...

Product changes Modifications to hardware and firmware of the device are not permitted. Incorrect operation or modifications to the device can endanger your safety or damage the device. Do not repair the device yourself. If the device is defective, please contact Phoenix Contact. Safety notes Observe the country-specific installation, safety, and accident prevention regulations. NOTE: Electrostatic discharge Electrostatic discharge can damage or destroy components. When handling the device, observe the necessary safety precautions against electrostatic discharge (ESD) in accordance with IEC 61340-5-1....

Applied directives and standards For directives and standards with which the safety module complies, refer to the certificate issued by the approval body and the EC declaration of conformity. These documents are available on the Internet. See phoenixcontact.net/products. The symbol informs you that you have to observe the instructions. Only install and operate the device once you have familiarized yourself with its properties by means of the user documentation. Latest documentation Always use the latest documentation. Changes or additions to documentation can be found on the Internet. See phoenixcontact.net/products....

Transport, storage, and unpacking NOTE: Electrostatic discharge Electrostatic discharge can damage or destroy components. When handling the device, observe the necessary safety precautions against electrostatic discharge (ESD) in accordance with IEC 61340-5-1. The device is delivered in cardboard packaging. • Please observe the notes on handling on the packaging. Suitable transport packaging Only transport the device in its original packaging or in packaging suitable for transport. Technical data and environmental conditions For transport, observe the humidity and air pressure specifications,...

Product description Short description The AXL F SSDOR4/2 1F safety module is a safe relay module of the Axioline F product family for use in a SafetyBridge system. To this end, the safety module is integrated into the Axioline F system. Please observe the description and information on the intended use. See “Intended use” on page 7. Safe relay outputs The module has four safety relays that can be operated via one or two channels, depending on the parameterization. In the case of 2-channel assignment, the safety module provides two safe relay outputs. In the case of 1-channel assignment, four...

Bus base module Electronics module Connector for connecting the supply voltage Function identification I/O connector Diagnostic and status indicators DIP switch PHOENIX CONTACT Structure of the safety module

Product description Supply voltages A safety module requires the following supply voltages: – Supply voltage UBus – Optional supply voltage UI for monitoring the connected switching elements (EDM) – Optional feed-in U0 and U1 for safe I/O supply (safety shutdown of Axioline F output modules) Observe the additional information and technical data in the documentation for the following components: – Axioline F product family – Bus coupler used. See “Documentation for the product family” on page 9. AXL F SSDOR4/2 1F Supply voltages Supply voltage UBus The communications power UL is supplied at the...

Voltage supply requirements WARNING: Loss of safety function The use of unsuitable power supplies can result in loss of the safety function. • Ensure that the following voltage supply requirements are fulfilled. NOTE: Module damage Parallel protection against polarity reversal is only implemented in the module for a limited period. • To prevent a defect at the module, ensure that the following voltage supply requirements are fulfilled. PELV power supply Only use power supply units with safe isolation and SELV/PELV. Make sure that the output voltage of the power supply does not exceed 32 V even...

Product description Supply voltages with fuse protection and FE PHOENIX CONTACT

Safe relay outputs The safety module has four safety relays, which can be used as follows: – For 2-channel assignment: two 2-channel relay outputs – For 1-channel assignment: four 1-channel relay outputs In 2-channel operation, the outputs have a fixed assignment to one another: – OUT0_CH1 to OUT0_CH2 – OUT1_CH1 to OUT1_CH2 Relay contact Terminal point Connector Basic illustration of the relay outputs Relay output 0, channel 1 Relay output 0, channel 2 Relay output 1, channel 1 Relay output 1, channel 2 WARNING: Loss of safety function / device defect Parallel connection of the safe relay outputs...