SnapLED Xtreme Homogeneity and reliability SnapLED Xtreme, the newest addition to the SnapLED family, creates an effective homogeneous styling through its innovative and unique ovalbatwing lens that provides even illumination over a wide rectangle. SnapLED Xtreme is a proven LED that enables homogenous appearance with a minimum number of LEDs and reduced secondary optic requirements. SnapLED Xtreme is available in the following colors: –– Super Red 635nm –– Red Orange 615nm PRIMARY APPLICATIONS Unique Batwing lens to reduce LED count and secondary optic to enable homogeneous appearance Low thermal resistance for better hot lumen performance Higher drive current capability for increased flux performance Highest maximum junction temperature for increased robustness of LED DS125 SnapLED Xtreme Product Datasheet ©2015 Lumileds Holding B.V. All rights

Table of Contents General Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Product Test Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Part Number Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Environmental Compliance . . . . . . . . . . . . . ....

General Product Information Product Test Conditions SnapLED Xtreme LEDs are tested and binned with 20ms monopulse (MP) at 300mA drive current, junction temperature, Tj, of 25ºC. Part Number Nomenclature Part numbers for SnapLED Xtreme follow the convention below: A 1 S X – B C C C D E 3 F G H J 0 0 Where: B – designates color (O=Red Orange, S=Super Red) C C C – designates minimum dominant wavelength (612=612nm, 632=632nm) D – designates the lens type (B=Batwing) – designates the binning condition (1=single binning 300mA) – designates minimum flux bin (See Product Bins and Labeling section) –...

Performance Characteristics Product Selection Guide Table 1. Product selection for SnapLED Xtreme at 20ms MP, 300mA, Tj=25°C. COLOR TYPICAL DOMINANT WAVELENGTH [1,2] (nm) PART NUMBER Notes for Table 1: 1. Dominant wavelength is derived from the CIE 1931 Chromaticity diagram and represents perceived color. 2. Lumileds maintains a tolerance of ±1nm for dominant wavelength measurements. Optical Characteristics Table 2. Typical optical characteristics for SnapLED Xtreme at 20ms MP, 300mA, Tj=25°C. PART NUMBER PEAK HORIZONTAL ANGLE 2θ PEAK VERTICAL ANGLE [1] 2θ Notes for Table 2: 1. The typical off...

Absolute Ratings Table 4. Absolute ratings for SnapLED Xtreme. Minimum DC Forward Current 10mA Maximum DC Forward Current 350mA Operating Case Temperature at Test Current111 -40°C to 110°C Operating Case Temperature at Maximum Current111 -40°C to 110°C Soldering Temperature Not applicable for clinching Allowable Reflow Cycles Not applicable for clinching Minimum ESD performance ra 8kV HBM (Class 3B), 1 kV CDM (Class III) 1. Proper current derating must be observed to maintain junction temperature below the maximum, so that the LED is maintained below the maximum rated operating case temperature....

Characteristic Curves Spectral Power Distribution Characteristics Figure 2: Typical normalized light output vs. junction temperature for SnapLED Xtreme at 300mA, 20ms MP. DS125 SnapLED Xtreme Product Datasheet 20151201 ©2015 Lumileds Holding B.V. All rights reserved.

Figure 3: Typical normalized light output vs. forward current for SnapLED Xtreme at T> 25°C. Forward Current Characteristics Figure 4a: Typical forward current vs. forward voltage for SnapLED Xtreme at Tj= 25°C. DS125 SnapLED Xtreme Product Datasheet 20151201 ©2015 Lumileds Holding B.V. All rights reserved.

Figure 4b: Typical forward voltage vs. junction temperature for SnapLED Xtreme at 300mA, 20ms MP. Radiation Pattern Characteristics Angle [degrees] Figure 5: Typical radiation pattern for SnapLED Xtreme at 300mA, 20ms MP. DS125 SnapLED Xtreme Product Datasheet 20151201 ©2015 Lumileds Holding B.V. All rights reserved.

Operating Limits Characteristics Figure 6: Maximum forward current vs. case temperature for SnapLED Xtreme. Thermal Resistance Figure 7: Approximate total thermal resistance vs. clinch frame area per anode. DS125 SnapLED Xtreme Product Datasheet 20151201 ©2015 Lumileds Holding B.V. All rights reserved.

Product Bin and Labeling Definitions Designing with SnapLED Xtreme Flux bins supportable for car programs depend on product color and program start- and end-of-production date. Flux roadmaps by year and product color are maintained and available from the sales representative. Please contact local sales representative to request the flux bin range with best supportability for program timing. Decoding Product Bin Labeling In the manufacturing of semiconductor products, there are variations in performance around the average values given in the technical datasheets. For this reason, Lumileds bins...

Color Codes Table 6. Color code definitions for SnapLED Xtreme at 20ms MP, 300mA, Tj=25°C. 1. Lumileds maintains a tolerance of ±0.06V on forward voltage measurements. DS125 SnapLED Xtreme Product Datasheet 20151201 ©2015 Lumileds Holding B.V. All rights reserved.

Mechanical Dimensions Figure 8: Mechanical dimensions for SnapLED Xtreme. Notes for Figure 8: 1. Drawings are not to scale. 2. All dimensions are in millimeters. 3. Cathode lead is indicated with a “C” and anode lead is indicated with an “A” (image is for illustration purposes only). 4. Clinch joint locations shown in dashed lines on top view of the emitter (11.5mm spacing). DS125 SnapLED Xtreme Product Datasheet 20151201 ©2015 Lumileds Holding B.V. All rights reserved