LUXEON Rebel, Red-Orange & Amber High flux solution for signaling applications Automotive grade LUXEON Rebel LEDs are designed and tested to meet and exceed expectations for reliability, performance and lifetime in all vehicle applications. LUXEON Rebel Red-Orange and Amber LEDs are particularly advantageous for both efficient light guide coupling and automotive tail applications, and for high brightness automotive applications. Lumileds automotive color binning structure meets both SAE and ECE color specifications. LUXEON Rebel meets both SAE and ECE color specifications and provides finer granularity than existing systems. Primary Applications High flux output provides flexibility in styling and optical design Low forward voltage results in higher efficacy and lower solution costs Side Marker Electrically isolated thermal pad to reduce thermal management engineering costs AEC-Q101C qualified and PPAP documentation available DS59 LUXEON Rebel Red-Orange & Amber Product Datasheet ©2015 Lumileds Holding B.V. All rights reserved.

Table of Contents General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Part Number Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 LED Lifetime Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Environmental...

Part Number Nomenclature LUXEON Rebel is tested and binned at 350mA. The part number designation is explained as follows: L X M A - A B C D - E F G H Where: A — designates radiation pattern (value P for Lambertian) B — designates color variant (L for amber, H for red-orange) C — designates color variant (0 for automotive amber and red-orange) D — designates technology (1 for automotive amber and red-orange standard flux direct color; 2 for red-orange high flux direct color) E — reserved for future product offerings FGH — minimum luminous flux (lm) performance Products tested and binned at 350mA...

1. LUXEON Rebel is tested and binned at 350mA. 2. Dominant wavelength is derived from the CIE 1931 Chromaticity diagram and represents the perceived color. Lumileds maintains a tolerance of ±0.5 nm for dominant wavelength measurements. 3. Spectral width at 1/2 of the peak intensity. 4. Total angle at which 90% of total luminous flux is captured. 5. Viewing angle is the off axis angle from lamp centerline where the luminous intensity is 1/2 of the peak value. 6. Junction temperature is estimated based on instant measurement at thermal pad temperature of 25°C. DS59 LUXEON Rebel Red-Orange & Amber...

Electrical Characteristics at 350mA for LUXEON Rebel, Junction Temperature, Tj = 25°C Part Number Typical Dynamic Resistance [4] (Q) Rn Typical Temperature Coefficient of Forward Voltage [2] (mV/°C) AVf/ DTj Typical Thermal Resistance Junction to Thermal Pad (°C/W) [3] R0 ,_r 1. Lumileds maintains a tolerance of ±0.06V on forward voltage measurements. 3. Does not include wall plug efficiency. 4. Dynamic resistance is the inverse of the slope in the linear forward voltage model for LEDs. See Forward Voltage vs. Forward Current curves. Typical Electrical Characteristics at 700mA for LUXEON Rebel,...

Red-Orange/Amber DC Forward Current (mA) Peak Pulsed Forward Current (mA) Average Forward Current (mA) ESD Sensitivity [5] LED Junction Temperature [1] [3] [4] Operating Case Temperature [4] Storage Temperature Soldering Temperature Allowable Reflow Cycles Autoclave Conditions -40°C - 135°C JEDEC 020c 260°C 3 121°C at 2 ATM 100% Relative Humidity for 96 Hours Maximum See Note 2 1. Proper current derating must be observed to maintain junction temperature below the maximum. 2. LUXEON Rebel LEDs are not designed to be driven in reverse bias. 3. LUXEON Rebel Automotive LEDs driven at maximum LED...

Reflow Soldering Characteristics Temperature Profile for Table 7. Table 7. Profile Feature Lead Free Assembly Average Ramp-Up Rate (Tsmax to Tp) Preheat Temperature Min (Tsmin) Preheat Temperature Max (Tsmax) Preheat Time (tsmin to tsmax) Time Maintained Above Temperature TL (tL) Peak / Classification Temperature (TP) Time Within 5°C of Actual Peak Temperature (tP) Ramp - Down Rate Time 25°C to Peak Temperature Note for Table 7: • All temperatures refer to the application Printed Circuit Board (PCB), measured on the surface adjacent to the package body. DS59 LUXEON Rebel Red-Orange & Amber Product...

Mechanical Dimensions Figure 1. Package outline drawing. Notes for Figure 1: 1. Do not handle the device by the lens—care must be taken to avoid damage to the lens or the interior of the device that can be damaged by excessive force to the lens. 2. Drawings not to scale. 3. All dimensions are in millimeters. 4. The Thermal Pad is electrically isolated from the Anode and Cathode contact pads. DS59 LUXEON Rebel Red-Orange & Amber Product Datasheet 20140904 ©2015 Lumileds Holding B.V. All rights reserved.

Figure 2. Solder pad layout. Note for Figure 2: 1. The Thermal Pad is electrically isolated from the Anode and Cathode contact pads. Wavelength Characteristics Red-Orange and Amber AlInGap at Test Current Thermal Pad Temperature = 25°C Relative Spectral Power Distribution Wavelength (nm) Figure 3. Relative intensity vs. wavelength. DS59 LUXEON Rebel Red-Orange & Amber Product Datasheet 20140904 ©2015 Lumileds Holding B.V. All rights reserved.

Typical Light Output Characteristics over Temperature Red-Orange and Amber AlInGap at 350mA Current 2.000 Relative Luminous Flux Thermal Pad Themperature (°C) Figure 4. Relative light output vs. thermal pad temperature for red-orange and amber AlInGaP at Test Current (Monopulse Measurement). DS59 LUXEON Rebel Red-Orange & Amber Product Datasheet 20140904 ©2015 Lumileds Holding B.V. All rights reserved.