General Illumination LUXEON Rebel PLUS The original high-power LED LUXEON Rebel PLUS is designed with the highest possible efficacy and light output from an industry standard 4530 package witha 2.5mm2 dome. With hot testing and color binning, every LUXEON Rebel PLUS is tested and specified at real world operating conditions — 85°C. Our exceptional color control enables design simplicity for luminaire manufacturers and ensures that they can be confident in color consistency from LED to LED. The superior quality of light, light output, and real world efficacy enable leading performance and efficient solution development in a wide variety of outdoor and industry lighting segments. Primary Applications 3- & 5-step MacAdam ellipse: Freedom from Binning for superior quality of light Ability to deliver high Lm/$ for Indoor applications Low typical Vf ~ 2.8V Small optical source size Full range of CCTS in 80CRI minimum LM-80 test report available DS107 LUXEON Rebel PLUS Product Datasheet ©2015 Lumileds Holding B.V. All rights reserved.

Table of Contents General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Part Number Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Lumen Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Environmental...

General Information Part Number Nomenclature LUXEON Rebel PLUS emitters are tested and binned “hot” under conditions comparable to those found in “realworld” lighting products. The test conditions for LUXEON Rebel PLUS are 350mA D.C. with junction temperature at 85°C. The part number designation for the LUXEON Rebel PLUS emitters is explained as follows: LX18-P1XX-Y Where: 8 — designates minimum CRI performance (value 8 = 80 minimum) P — designates radiation pattern (value P for Lambertian) 1 — 80 CRI min designation XX — esignates nominal ANSI CCT (value 27 = 2700K, 30 = 3000K, 35 = 3500K, 40...

Product Selection & Optical Characteristics Product Selection Guide for LUXEON Rebel PLUS Emitters 1 Test current is 350mA D C for all LX18-P1xx emitters 2 Total angle at which 90% of total luminous flux is captured 3 Viewing angle is the off axis angle from lamp centerline where the luminous intensity is 1/2 of the peak value DS107 LUXEON Rebel PLUS Product Datasheet 20140930 ©2015 Lumileds Holding B.V. All rights reserved.

Electrical Characteristics Electrical Characteristics at 350mA for LUXEON Rebel PLUS, DS107 LUXEON Rebel PLUS Product Datasheet 20140930 ©2015 Lumileds Holding B.V. All rights reserved.

Reflow Soldering Characteristics Figure 1. Temperature Profile for Table 6. Table 6. Profile Feature Lead Free Assembly Average Ramp-Up Rate ( Tsmax to Tp ) Preheat Temperature Min ( Tsmin ) Preheat Temperature Max ( Tsmax ) Preheat Time (tsmin to tsmax ) Time Maintained Above Temperature TL Peak / Classification Temperature ( TP ) Time Within 5°C of Actual Peak Temperature (tP) Ramp-Down Rate Time 25°C to Peak Temperature Note for Table 6: 1. All temperatures refer to the application Printed Circuit Board (PCB), measured on the surface adjacent to the package body. DS107 LUXEON Rebel PLUS Product...

Mechanical Dimensions Figure 2. Package outline drawing. Notes for Figure 2: 1. Do not handle the device by the lens, as the lens or the interior of the device can be damaged by excessive force to the lens. 2. Drawings not to scale. All dimensions are in millimeters. 3. The thermal pad is electrically isolated from the anode and cathode contact pads. DS107 LUXEON Rebel PLUS Product Datasheet 20140930 ©2015 Lumileds Holding B.V. All rights reserved.

Figure 3. Pad configuration. Note for Figure 3: 1. The Thermal Pad is electrically isolated from the Anode and Cathode contact pads. Figure 4. Solder pad layout. Notes for Figure 4: 1. The photograph shows the recommended LUXEON Rebel PLUS layout on Printed Circuit Board (PCB). This design easily achieves a thermal resistance of 7K/W. 2. Application Brief AB32 provides extensive details for this layout. Printed Circuit Board layout files (.dwg) are available at www.lumileds.com. DS107 LUXEON Rebel PLUS Product Datasheet 20140930 ©2015 Lumileds Holding B.V. All rights reserved.

Typical Light Output Characteristics over Temperature All LUXEON Rebel PLUS Emitters at Test Current, 350mA 1.15 Normalized Flux, [-] Figure 5. Relative light output vs. junction temperature. DS107 LUXEON Rebel PLUS Product Datasheet 20140930 ©2015 Lumileds Holding B.V. All rights reserved.

Typical Forward Current Characteristics All LUXEON Rebel PLUS Emitters, Junction Temperature = 85°C 700 Figure 6. Forward current vs. forward voltage. Typical Relative Luminous Flux vs. Forward Current for All LUXEON Rebel PLUS Emitters, Junction Temperature = 85°C 1.8 Normalized Flux, [-] Figure 7. Typical relative luminous flux vs. forward current, junction temperature = 85°C. DS107 LUXEON Rebel PLUS Product Datasheet 20140930 ©2015 Lumileds Holding B.V. All rights reserved.

Typical Radiation Patterns Relative Spectral Distribution for LUXEON Rebel PLUS Emitters 1 Relative Power, [-] Figure 8. Cartesian plot of typical luminous intensity. Normalized Flux [%] Figure 9. Typical polar radiation pattern. DS107 LUXEON Rebel PLUS Product Datasheet 20140930 ©2015 Lumileds Holding B.V. All rights reserved.

Emitter Pocket Tape Packaging EMETT EOCEETS WITE TAEE Figure 10. Emitter pocket tape packaging. DS107 LUXEON Rebel PLUS Product Datasheet 20140930 ©2015 Lumileds Holding B.V. AN rights reserved.

Emitter Reel Packaging Figure 11. Emitter reel packaging. DS107 LUXEON Rebel PLUS Product Datasheet 20140930 ©2015 Lumileds Holding B.V. All rights reserved.