*mydirectindustry

LUXEON Rebel ES

Product catalog summary

Introduction
The LUXEON Rebel ES is a high flux LED designed for outdoor and industrial lighting applications. It is tested and binned at 700mA, providing flexibility for high lumen or energy-efficient designs. The product is recognized for its quality, reliability, and performance.

Features and Benefits
- Offers high lm/$ for cost-effective applications.
- Provides a broad emitter portfolio for various applications.
- Includes diverse CCT and CRI combinations.
- Supports an extensive ecosystem for easy design-in and quick ROI.
- LM-80 test report is available.

Product Nomenclature
The series includes LEDs for illumination applications, with part numbers based on radiation pattern, color, color variant, and test current.

Average Lumen Maintenance Characteristics
Projected to maintain 70% lumen output (L70) at 50,000 hours with a forward current of 1000mA, assuming a junction temperature at or below 135°C.

Environmental Compliance
Complies with RoHS and REACH directives, avoiding hazardous substances like lead and mercury.

Product Selection Guide
Performance measured at a thermal pad temperature of 25°C, with various CCTs and CRIs, and typical luminous flux values for different forward currents.

Optical Characteristics
At 700mA, the typical total included angle is 160°, and the viewing angle is 120° for all emitters.

Electrical Characteristics
Forward voltage is typically 2.90V at 700mA, with a thermal resistance of 6°C/W. The temperature coefficient of forward voltage ranges from -2.0 to -4.0 mV/°C.

Absolute Maximum Ratings
- DC Forward Current: 1000mA
- Peak Pulsed Forward Current: 1200mA
- ESD Sensitivity: < 8000V HBM
- LED Junction Temperature: 150°C

Conclusion
The LUXEON Rebel ES series offers a robust solution for high-performance lighting applications, ensuring compliance with environmental standards and providing reliable performance metrics.

Specifications
- Operating and Storage Temperature: -40°C to 135°C
- Soldering Temperature: 260°C (JEDEC 020c)
- Allowable Reflow Cycles: 3
- Reverse Voltage: Not designed for reverse bias

Procedures and Guidelines
- Current derating is necessary to maintain junction temperature below maximum.
- Ripple with frequencies ≥ 100 Hz and amplitude ≤ 200mA is acceptable if average current does not exceed 1000mA.
- Pulsed operation with peak drive current of 1200mA is acceptable if pulse on-time is ≤ 5 ms per cycle and duty cycle is ≤ 50%.

Reflow Soldering Characteristics
- Average Ramp-Up Rate: 3°C/second max
- Preheat Temperature: 150°C to 200°C
- Preheat Time: 60 - 180 seconds
- Temperature (T_L): 217°C
- Time Above T_L: 60 - 150 seconds
- Peak Temperature: 260°C
- Time Within 5°C of Peak: 20 - 40 seconds
- Ramp-Down Rate: 6°C/second max
- Time 25°C to Peak: 8 minutes max

Mechanical Dimensions
- Handle with care to avoid damage to the lens.
- Thermal pad is electrically isolated from contact pads.

Solder Pad Design
- Recommended layout achieves thermal resistance of 7K/W.

Color Spectrum and Light Output
- Various emitters tested at 25°C show different spectral distributions.
- Relative luminous flux and efficacy vary with temperature and forward current.

Product Binning and Labeling
- Emitters are binned for luminous flux, color, and forward voltage.
- Bins are labeled with a four-digit alphanumeric code.
- Flux bins range from 120 lm to 320 lm.

Bin Structures
- 4100K Neutral White and 5650K Cool White emitters are binned by x,y coordinates with specific CCT ranges.

Specifications
LUXEON Rebel ES emitters are tested and binned by x, y color coordinates. The document provides detailed bin structures for various emitters, covering a CCT range from 2580K to 7040K, with specific x, y coordinates listed for each bin.

Procedures
Emitters are tested at 700mA, with forward voltage (Vf) bins outlined with minimum and maximum values. Availability of specific bins may vary by production run and product performance.

Norms and Standards
Lumileds maintains a tester tolerance of ± 0.005 on x, y color coordinates, emphasizing the ANSI 1/4th quadrant color bin structure for accurate color representation.

Recommendations
Users are advised to consider variability in product availability across different bins and refer to the most accurate information provided by Lumileds.

Key Data from Tables
Tables provide detailed x, y coordinates for various color bins and list forward voltage bins with specific voltage ranges.

About Lumileds
Lumileds is a leader in light engine innovation, focusing on quality and reliability across automotive, consumer, and illumination markets, with a century-long commitment to pioneering breakthrough products.

Catalog excerpts

General Illumination LUXEON Rebel ES High value and easy design-in LUXEON Rebel ES is a high flux, high gives you the flexibility you need to design luminaires and lamps for outdoor and industrial lighting applications and bring them to market. Tested and binned at 700mA, confidently design LUXEON Rebel ES into high lumen applications or create more energy efficient devices using the same emitter. Luminaire manufacturers and designers count on LUXEON Rebel ES for quality, reliability and in-device performance. Primary Applications High lm/$ for cost competitive applications Broad portfolio of emitters for indoor and outdoor applications CCT and CRI combinations to support a wide range of applications Specialty Lighting Extensive applications ecosystem for easy design-in and quick ROI LM-80 test report available DS061 LUXEON Rebel ES Product Datasheet ©2015 Lumileds Holding B.V. All rights reserved.

Open the catalog to page 1

Table of Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Product Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

Open the catalog to page 2

General Information Product Nomenclature LUXEON Rebel ES is tested and binned at 700mA, with current pulse duration of 20 ms. All characteristic charts where the thermal pad is kept at constant temperature (25°C typically) are measured with current pulse duration of 20 ms. Under these conditions, junction temperature and thermal pad temperature are the same. The LUXEON Rebel ES family of emitters contain a series of LEDs designed for Illumination applications. The part number designation for the LXML series is explained as follows: LXML-ABCD Where: A — designates radiation pattern (value P for...

Open the catalog to page 3

Average Lumen Maintenance Characteristics Lumen maintenance for solid state lighting devices (LEDs) is typically defined in terms of the percentage of initial light output remaining after a specified period of time. Lumileds projects that LUXEON Rebel ES products will deliver, on average, 70% lumen maintenance (L70) at 50,000 hours of operation at a forward current of 1000mA. This projection is based on constant current operation with junction temperature maintained at or below 135°C. This performance is based on independent test data, Lumileds historical data from tests run on similar material...

Open the catalog to page 4

Product Selection Guide for LUXEON Rebel ES 1 Typical luminous flux performance within published operating conditions Lumileds maintains a tolerance of ± 6 5% on luminous flux measurments DS061 LUXEON Rebel ES Product Datasheet 20140728 ©2015 Lumileds Holding B.V. All rights reserved.

Open the catalog to page 5

Optical Characteristics for LUXEON Rebel ES at Test Current[1] 1 Test current is 700mA for all LXML-PWx2, LXWx-PWxxand LXH7-PWxx emitters 2 Total angle at which 90% of total luminous flux is captured 3 Viewing angle is the off axis angle from lamp centerline where the luminous intensity is 1/2 of the peak value DS061 LUXEON Rebel ES Product Datasheet 20140728 ©2015 Lumileds Holding B.V. All rights reserved.

Open the catalog to page 6

Electrical Characteristics at 700mA for LUXEON Rebel ES Thermal Pad Temperature = 25°C Table 4. Forward Voltage Vf [1] (V) Typ. Temperature Coefficient of Forward Voltage [2] (mV/°C) DVf / DTJ Typical Thermal Resistance Junction to Thermal Pad (°C/W) Ru J-C Part Number Nominal CCT/Color Notes for Table 4: 1. Lumileds maintains a tolerance of ±0.06V on forward voltage measurements. 2. Measured between 25°C = TJ = 110°C at If = 700mA. Typical Electrical Characteristics at 350mA, 700mA and 1000mA for LUXEON Rebel ES Thermal Pad Temperature = 25°C Table 5. Nominal CCT/Color Part Number Typical Forward...

Open the catalog to page 7

Absolute Maximum Ratings Table 6. Parameter Peak Pulsed Forward Current (mA) < 8000V Human Body Model (HBM) Class 3A JESD22-A114-E Operating Case Temperature at 700mA Storage Temperature Soldering Temperature Allowable Reflow Cycles LUXEON Rebel ES LEDs are not designed to be driven in reverse bias Notes for Table 6: 1. Proper current derating must be observed to maintain junction temperature below the maximum. For additional information on thermal measurement guidelines please refer to Application Brief AB33. 2. Residual periodic variations due to power conversion from alternating current (AC)...

Open the catalog to page 8

Reflow Soldering Characteristics Temperature profile for Table 8. Table 8. Profile Feature Lead Free Assembly Average Ramp-Up Rate (Tsmax to Tp) Preheat Temperature Min (Tsmin) Preheat Temperature Max (Tsmax) Preheat Time (tsmin to tsmax) Time Maintained Above Temperature (TL) Peak / Classification Temperature (TP) Time Within 5°C of Actual Peak Temperature (tP) Ramp - Down Rate Time 25°C to Peak Temperature Notes for Table 8: 1. All temperatures refer to the application Printed Circuit Board (PCB), measured on the surface adjacent to the package body. 2. For additional information on thermal...

Open the catalog to page 9

Mechanical Dimensions Figure 1. Package outline drawing. 1. Do not handle the device by the lens—care must be taken to avoid damage to the lens or the interior of the device that can be damaged by excessive force to the lens 4. The thermal pad is electrically isolated from the anode and cathode contact pads DS061 LUXEON Rebel ES Product Datasheet 20140728 ©2015 Lurnileds Holding B.V. All rights reserved.

Open the catalog to page 10

Figure 2. Pad configuration. Note for Figure 2: 1. The Thermal Pad is electrically isolated from the Anode and Cathode contact pads. Figure 3. Solder pad layout. Notes for Figure 3: 1. The photograph shows the recommended LUXEON Rebel ES layout on Printed Circuit Board (PCB). This design easily achieves a thermal resistance of 7K/W. 2. Application Brief AB32 provides extensive details for this layout. Printed Circuit Board layout files (.dwg) are available at www.lumileds.com. DS061 LUXEON Rebel ES Product Datasheet 20140728 ©2015 Lumileds Holding B.V. All rights reserved.

Open the catalog to page 11

LUXEON Rebel ES

LUXEON Rebel ES

Catalog excerpts

All Philips Lumileds Lighting Company catalogs and technical brochures

Archived catalogs