LUXEON Rebel Red-Orange & Amber Introduction Automotive grade LUXEON Rebel LEDs are designed and tested to meet and exceed expectations for reliability, performance and lifetime in all vehicle applications. LUXEON Rebel Red-Orange and Amber LEDs are particularly advantageous for both efficient light guide coupling and automotive tail applications, and for high brightness automotive Rear Fog applications. Philips Lumileds automotive color binning structure meets both SAE and ECE color specifications. LUXEON Rebel Automotive is AEC-Q101 qualified. PPAP documentation is available upon request. • Delivers industry leading flux • Fewer LEDs per function • Turn Lamps • Longest history in high power exterior lighting applications • Low thermal resistance • Low forward voltage • Electrically isolated thermal pad • Stop/Tail Lamps • Side Marker Lamps • Proven reliability • Lower heat sink costs, higher lighting efficacy • Higher lighting efficacy • Reduces thermal management engineering costs LUXEON Rebel Reds DS59 ©2014 Philips Lumileds Lighting Company.

Table of Contents General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Part Number Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 LED Lifetime Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Environmental...

General Information Part Number Nomenclature LUXEON Rebel is tested and binned at 350mA. The part number designation is explained as follows: LXMA-ABCD-EFGH Where: A — designates radiation pattern (value P for Lambertian) B — designates color variant (L for amber, H for red-orange) C — designates color variant (0 for automotive amber and red-orange) D — designates technology (1 for automotive amber and red-orange standard flux direct color; 2 for red-orange high flux direct color) E — reserved for future product offerings FGH — minimum luminous flux (lm) performance Products tested and binned...

Flux Characteristics Flux Characteristics for LUXEON Rebel, Junction Temperature, Tj = 25°C [4] Table 1. Typical Performance at Maximum Current Performance at Binning Current Minimum Luminous Flux (lm) FV [1] [3] Typical Luminous Flux (lm) FV [2] [3] Note for Table 1: 1. Minimum luminous flux performance guaranteed within published operating conditions. Philips Lumileds maintains a tolerance of ± 6.5% on flux measurements. 2. Typical luminous flux or radiometric power performance when device is operated within published operating conditions. 3. LUXEON Rebel products with even higher luminous...

Electrical Characteristics Electrical Characteristics at 350mA for LUXEON Rebel, 1 Philips Lumileds maintains a tolerance of ±0 06V on forward voltage measurements 3 Does not include wall plug efficiency 4 Dynamic resistance is the inverse of the slope in the linear forward voltage model for LEDs See Forward Voltage vs Forward Current curves Typical Electrical Characteristics at 700mA for LUXEON Rebel, Part Number Typical Forwa^d Volta^e Vf 1 Philips Lumileds maintains a tolerance of ±0 06V on forward voltage measurements LUXEON Rebel Reds Datasheet DS59 20140904 ©2014 Philips Lumileds Lighting...

Absolute Maximum Ratings Table 5a. Parameter Peak Pulsed Forward Current (mA) Average Forward Current (mA) LED Junction Temperature [1] [3] [4] Operating Case Temperature Storage Temperature Soldering Temperature Allowable Reflow Cycles Autoclave Conditions 121°C at 2 ATM 100% Relative Humidity for 96 Hours Maximum Notes for Table 5a: 1. Proper current derating must be observed to maintain junction temperature below the maximum. 2. LUXEON Rebel LEDs are not designed to be driven in reverse bias. 3. LUXEON Rebel Automotive LEDs driven at maximum LED junction temperature will have limited lifetime....

Reflow Soldering Characteristics Temperature Profile for Table 7. Table 7. Profile Feature Lead Free Assembly Average Ramp-Up Rate (Tsmax to Tp) Preheat Temperature Min (Tsmin) Preheat Temperature Max (Tsmax) Preheat Time (tsmin to tsmax) Time Maintained Above Temperature TL (tL) Peak / Classification Temperature (TP) Time Within 5°C of Actual Peak Temperature (tP) Ramp - Down Rate Time 25°C to Peak Temperature Note for Table 7: • All temperatures refer to the application Printed Circuit Board (PCB), measured on the surface adjacent to the package body. LUXEON Rebel Reds Datasheet DS59 20140904...

Mechanical Dimensions Figure 1. Package outline drawing. Notes for Figure 1: 1. Do not handle the device by the lens—care must be taken to avoid damage to the lens or the interior of the device that can be damaged by excessive force to the lens. 2. Drawings not to scale. 3. All dimensions are in millimeters. 4. The Thermal Pad is electrically isolated from the Anode and Cathode contact pads. LUXEON Rebel Reds Datasheet DS59 20140904 ©2014 Philips Lumileds Lighting Company.

Figure 2. Solder pad layout. 1. The Thermal Pad is electrically isolated from the Anode and Cathode contact pads Wavelength Characteristics Red-Orange and Amber AllnGap at Test Current Thermal Pad Temperature = 25°C Figure 3. Relative intensity vs. wavelength. LUXEON Rebel Reds Datasheet DS59 20140904 ©2014 Philips Lumileds Lighting Company

Typical Light Output Characteristics over Temperature Red-Orange and Amber AlInGap at 350mA Current 2.000 Relative Luminous Flux Thermal Pad Themperature (°C) Figure 4. Relative light output vs. thermal pad temperature for red-orange and amber AlInGaP at Test Current (Monopulse Measurement). LUXEON Rebel Reds Datasheet DS59 20140904 ©2014 Philips Lumileds Lighting Company.