LUXEON F PC Amber Industry-leading solutions for turn applications LUXEON F PC Amber and LUXEON F Plus PC Amber automotive LEDs deliver design flexibility and advanced functionality. These products, with their miniaturized form factor are designed to support daytime running lights, side marker and turn signal applications. The Lumileds automotive binning structure meets both SAE and ECE color specifications and is hot binned at 85°C, consistent with actual automotive operational environments. LUXEON F PC Amber and LUXEON F Plus PC Amber provide industry-leading solutions for your front and rear turn applications. All LUXEON F LEDs are AEC-Q101 qualified. Primary ApplicationS Higher drive current capability for increased flux performance Daytime Running Lights Low thermal resistance for better hot lumen performance Side Marker Standard packaging for low cost and ease of manufacturability Hot binned at 85°C mono pulse (MP) to match closer to operating conditions –– Front Turn –– Rear Turn DS109 LUXEON F PC Amber Product Datasheet ©2016 Lumileds Holding B.V. All rights r

Table of Contents General Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Product Test Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Part Number Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Environmental Compliance . . . . . . . . . . . . . ....

General Product Information Product Test Conditions LUXEON F PC Amber LEDs are tested and binned using a 20ms monopulse (MP) at 350mA drive current for LUXEON F PC Amber and 1000mA for LUXEON F Plus PC Amber, case temperature, Tc, of 85ºC. Tj = LED junction temperature Tc = Tsolder = Case Temperature Tsensor = Temperature at thermos sensor location (not solder location) Figure 1: Example of case temperature location on sample board for LUXEON F. Part Number Nomenclature Part numbers for LUXEON F PC Amber and LUXEON F Plus PC Amber follow the convention below: L F M H – A B C – E F G H Where:...

Performance Characteristics Product Selection Guide Table 1. Product selection for LUXEON F PC Amber and LUXEON F Plus PC Amber at 20ms MP specified test current, TC=85°C. 1. Spectral width at Vi of the peak intensity. 2. Total angle at which 90% of total luminous flux is captured. 3. Viewing angle is the off axis angle from the LED centerline where the luminous intensity is Vi of the peak value. 3>S109 LUXEON F PC Amber Product Datasheet 20160315 ©2016 Lumileds Holding B.V. All rights reserved.

Electrical and Thermal Characteristics Table 3. Electrical and thermal characteristics for LUXEON F PC Amber and LUXEON F Plus PC Amber at MP specified test current, TC=85°C. Part Number Typical Thermal Resistance — Junction to CASE (°C/W) Temperature Coefficient of Forward Voltage [3] (mV/°C) ΔVf / ΔTj Notes for Table 3: 1. Lumileds maintains a tolerance of ±0.06V on forward voltage measurements. 2. Dynamic resistance is the inverse of the slope in linear forward voltage model for LEDs. 3. Measured between Tc=80°C and Tc=90°C at binning current. 4. Rθ j-c electr: Electrical thermal resistance...

Characteristic Curves Spectral Power Distribution Characteristics Figure 2: Typical normalized power vs. wavelength for LUXEON F PC Amber and LUXEON F Plus PC Amber at test current, TC=85°C. Light Output Characteristics Figure 3a: Typical normalized light output vs. case temperature for LUXEON F PC Amber at 20ms MP, 350mA. DS109 LUXEON F PC Amber Product Datasheet 20160315 ©2016 Lumileds Holding B.V. All rights reserved.

Figure 3b: Typical normalized light output vs. case temperature for LUXEON F Plus PC Amber at 20ms MP, 1000mA. Figure 4a: Typical normalized light output vs. forward current for LUXEON F PC Amber. DS109 LUXEON F PC Amber Product Datasheet 20160315 ©2016 Lumileds Holding B.V. All rights reserved.

Figure 5: Typical forward current vs. forward voltage for LUXEON F PC Amber and LUXEON F Plus PC Amber at 20ms MP at specified test temperature. DS109 LUXEON F PC Amber Product Datasheet 20160315 ©2016 Lumileds Holding B.V. All rights reserved.

Figure 6: Typical forward voltage shift vs. case temperature for LUXEON F PC Amber and LUXEON F Plus PC Amber at 20ms MP, specified test current. Color Shift Characteristics Figure 7a. Typical color shift in CIE 1931 x, y coordinates for LUXEON F PC Amber at 20ms MP, 350mA. DS109 LUXEON F PC Amber Product Datasheet 20160315 ©2016 Lumileds Holding B.V. All rights reserved.

Figure 7b. Typical color shift in CIE1931 x,y coordinates for LUXEON F Plus PC Amber at 20ms MP, 1000mA. Radiation Pattern Characteristics Angle [degrees] Figure 8: Typical radiation pattern for LUXEON F PC Amber and LUXEON F Plus PC Amber at 20ms MP specified test current, TC=85°C. DS109 LUXEON F PC Amber Product Datasheet 20160315 ©2016 Lumileds Holding B.V. All rights reserved.

Operating Limits Characteristics Figure 9: Maximum forward current vs. case temperature for LUXEON F PC Amber and LUXEON F Plus PC Amber. Permissible Pulse Handling Characteristics Figure 10a: Permissible pulse handling capability for LUXEON F PC Amber. DS109 LUXEON F PC Amber Product Datasheet 20160315 ©2016 Lumileds Holding B.V. All rights reserved.

Figure 10b: Permissible pulse handling capability for LUXEON F Plus PC Amber. DS109 LUXEON F PC Amber Product Datasheet 20160315 ©2016 Lumileds Holding B.V. All rights reserved.

Product Bin and Labeling Definitions Designing with LUXEON F PC Amber and LUXEON F Plus PC Amber Flux bins supportable for car programs depend on product color and program start- and end-of-production date. Flux roadmaps by year and product color are maintained and available from the sales representative. Please contact your local sales representative to request the flux bin range with best supportability for program timing. Decoding Product Bin Labeling In the manufacturing of semiconductor products, there are variations in performance around the average values given in the technical datasheets....