video corpo cad

SCV series
10Pages

{{requestButtons}}

Catalog excerpts

SCV series - 1

IDEAL FOR NON-ROTATING VERTICAL OR LIGHT DUTY HORIZONTAL APPLICATIONS Rodlok® can be added to securely hold a static tool plate in place at any point of travel desired optional cushions and port controls available ideal for applications where rod drift due to system leakage, air-line rupture, or electric power loss is unacceptable optional stroke adjustment collars with shock pads are available on both extend and retract IMPROVED PHD’s Series CV Cylinder powers this unit for extra long life with a wide range of control and switch accessories anodized aluminum alloy body is supplied with counterbored holes for easy mounting of tooling and fixturing extra long self-lubricating bronze bushings anodized aluminum tool plate has modular mounting patterns to allow the attachment of other sizes of Series SCV Slides for 2-axis movement precision ground hardened guide shafts provide smooth, precise linear motion Major Benefits Industry Uses Oversize guide rods Simple design Ideal for non-rotating applications Easy tooling mounting to tool plate 8 bore sizes Units are powered by PHD’s rugged Series CV Cylinder, now with improved seal & bearing support Material handling/conveyors Snack foods Assembly machine builders General assembly

Open the catalog to page 1
SCV series - 2

Available in 1" [25 mm] increments. Minimum travel required for all Series SCV Slides is 1" [25 mm]. Consult PHD for other stroke lengths. TOOL PLATE EXTENSION Additional distance between tool plate and bearing body in 1" [25 mm] increments. Leave blank if additional extension is not required. SLIDE OPTIONS AE - Travel adjustment and shock pads on extension** AR - Travel adjustment and shock pads on retraction** Z1 - Corrosion resistant; guide shafts are hard chrome plated stainless steel or specially coated hardened steel, and appropriate coating on ferrous parts. CYLINDER C - CV Series...

Open the catalog to page 2
SCV series - 3

ENGINEERING DATA: SERIES SCV SLIDES GUIDE SHAFT DIAMETER in mm 0.394 10 SERIES SCV SPECIFICATIONS 35 psi min to 150 psi max [2.4 bar min to 10 bar max] air OPERATING PRESSURE -20¡ to +180¡F [-29¡ to +82¡C] OPERATING TEMPERATURE See table below TRAVEL TOLERANCE ±0.001 in [±.025 mm] of original position REPEATABILITY 80 in/sec [2 m/sec] max., zero load at 87 psi [6.9 bar] VELOCITY Factory lubricated for rated life LUBRICATION Field repairable MAINTENANCE BORE TYPICAL EFFECTIVE CYLINDER ROD BASE WEIGHT DIAMETER DYNAMIC LOAD AREA DIAMETER SLIDE in mm in mm DIRECTION in2 mm2 lb kg lb N 0.315 8...

Open the catalog to page 3
SCV series - 4

DIMENSIONS: SERIES SCV SLIDES K MIN A 2X THRU ¯ & C’BORE FOR DD SHCS TOOL PLATE EXTENSION 4X Y THREAD THRU FROM THIS SIDE C’BORE FROM OPPOSITE SIDE FOR P SHCS M NOTES: 1) FOR OPTION DIMENSIONS AND DETAILS, SEE OPTION PAGES 2) ALL DIMENSIONS ARE CENTERED ON CENTERLINE OF UNIT UNLESS OTHERWISE SPECIFIED 3) UNIT TRAVEL = STROKE + TOOL PLATE EXTENSION. THE TOTAL UNIT TRAVEL SHOULD NOT EXCEED THE MAXIMUM RECOMMENDED TRAVEL. 4) *PORTS MAY APPEAR ON EITHER SIDE OF THE SLIDE CENTERLINE BASED ON OPTION COMBINATIONS. 5) **ALL UNITS, EXCEPT PORT WITH PORT CONTROL ON SAME SIDE, COMPLY WITH DIN 3852...

Open the catalog to page 4
SCV series - 5

OPTIONS: SERIES SCV SLIDES AE TRAVEL ADJUSTMENT AND SHOCK PADS ON EXTENSION TRAVEL ADJUSTMENT AND SHOCK PADS ON RETRACTION Two travel adjustment stop collars with polyurethane shock pads are used for adjustment of slide retraction. The travel adjustment stop collars allow precise adjustment while the shock pads eliminate metal to metal contact, thereby reducing noise levels. Two travel adjustment stop collars with polyurethane shock pads are used for adjustment of slide extension. The travel adjustment stop collars allow precise adjustment while the shock pads eliminate metal to metal...

Open the catalog to page 5
SCV series - 6

OPTIONS: SERIES SCV SLIDES DB CUSHION CONTROL IN BOTH DIRECTIONS CUSHION CONTROL ON EXTEND ONLY Unit shown is -DB17, cushion in location 1 (standard) on extend end and cushion in location 7 on retract end. (Ports are shown in locations 3 & 5.) CUSHION CONTROL ON RETRACT ONLY (standard location 5) PHD cushions are designed for smooth deceleration at the ends of cylinder stroke. When the cushion is activated, the remaining volume in the cylinder must exhaust past an adjustable needle valve which controls the amount of deceleration. The effective cushion length for each bore size is shown in...

Open the catalog to page 6
SCV series - 7

OPTIONS: SERIES SCV SLIDES RODLOK KITS RODLOK SLIDE & RODLOK PHD’s Rodlok is ideal for locking the tool plate while in a static/stationary position. When the pressure is removed from the port of the Rodlok, the mechanism will grip the piston rod of the cylinder and prevent it from moving. The loads are held indefinitely without power. Rodlok performance is application and environment sensitive (Cleanliness of rod or Rodlok will also affect performance). THE RODLOK IS NOT DESIGNED TO BE USED AS A PERSONNEL SAFETY DEVICE. COMPLETE RODLOK* IMPERIAL PORT ADAPTOR 63461-07-1 63459-07-1 63460-07-1...

Open the catalog to page 7
SCV series - 8

OPTIONS: SERIES SCV SLIDES PORT CONTROLS® ON EXTEND ONLY (standard location 1) PORT CONTROLS® ON BOTH ENDS PORT CONTROLS® ON RETRACT ONLY (standard location 5) PHD’s Port Control® is a built-in flow control for regulating the speed of the slide through its entire stroke. The Port Control operates on the “meter-out” principle and features an adjustable needle in a cartridge with a check seal. The self-locking needle has micrometer threads and is adjustable under pressure. The needle determines the orifice size which controls the exhaust flow rate of the actuator. The check seal expands while...

Open the catalog to page 8
SCV series - 9

OPTIONS: SERIES SCV SLIDES UB ALTERNATE PORT LOCATION With this option, alternate port locations can be specified, providing increased flexibility and customer convenience. See option code below to specify port locations. Extend Location (Head) (1, 3) This option equips the cylinder with a magnetic band on the piston for use with PHD Reed and Solid State Switches listed below. These switches mount easily to the cylinder using “T” slots in the body. See the Switch section for complete switch information. MAGNET FOR PHD REED AND SOLID STATE SWITCHES Unit shown is -UB17, port in location 1 on...

Open the catalog to page 9

All PHD catalogs and technical brochures

  1. Series 8600

    6 Pages

  2. Series GRM

    96 Pages

  3. RCC series

    6 Pages

  4. GRW series

    8 Pages

  5. GRS series

    10 Pages

  6. PA series

    8 Pages

  7. BCZ series

    12 Pages

  8. PB & PC series

    16 Pages

  9. 1750 series

    3 Pages

  10. 190/191 series

    10 Pages

  11. CRS series

    14 Pages

  12. BCS series

    16 Pages

  13. Main Catalog

    644 Pages

Archived catalogs

  1. CLAMPS

    156 Pages