Adaptors, Transition Plates & Stanchions
46Pages

ADAPTORS, TRANSITION PLATES, AND STANCHIONS FOR EASE OF CONNECTING PHD PRODUCTS TOGETHER, PROVIDING THE MOST VERSATILE SOLUTION IN THE INDUSTRY. need new unit from engineering TRANSITION PLATES ADAPTORS, TRANSITION

GUIDELINES FOR MODULAR AUTOMATION Adaptors, Transition Plates, and Stanchions For Modular Automation • REDUCES ENGINEERING TIME • SIMPLIFIES DESIGN • COST-EFFECTIVE • ELIMINATES FABRICATION Simplify the design of your automation solutions using PHD’s wide range of adaptors, transition plates, and stanchions. The use of standard hardware makes it easy to combine axes of motion. The hardware provides an efficient means of assembling individual actuators into a complete automation device. An unlimited number of combinations can be achieved to satisfy your specific motion requirements. A...

GUIDELINES FOR MODULAR AUTOMATION PHD components and capacities are shown in the following sections: HOW TO USE THIS SECTION This section covers available hardware for the creation of PHD Modular Automation Devices. Each hardware subsection contains a grid layout showing the most common combinations of PHD actuators together with the proper Adaptor, Transition Plate, or Stanchion, and hardware to facilitate interconnection. The proper sizing of PHD actuators is derived from the individual product catalog sections. Follow the sequence below when selecting mechanical components for a parts...

ADAPTOR/ACTUATOR COMBINATIONS SECONDARY UNIT MINIATURE GRIPPERS LARGER GRIPPERS SEE REFERENCED PAGES FOR PROPER ADAPTOR SIZE AND KIT NUMBER SECTION 4 MINIATURE ROTARY ACTUATORS LARGER ROTARY ACTUATORS MULTI-MOTION ACTUATORS ADAPTORS, TRANSITION

ADAPTOR/ACTUATOR COMBINATIONS SECONDARY UNIT MINIATURE ROTARY ACTUATORS LARGER ROTARY ACTUATORS MULTI-MOTION ACTUATORS PHD Adaptors also provide an easy means of attaching tooling, fixturing, and arms for the creation of pick and place devices. They provide a bolt pattern on the end of various PHD Actuator shafts making it easy to mount other PHD products and customer-provided tooling. ADAPTORS, TRANSITION

HUB ADAPTORS: IMPERIAL UNITS HUB ADAPTORS ALLOW COMBINING ACTUATORS TO A ROUND OUTPUT SHAFT ORDERING DATA HUB SIZE SHAFT DIA. SIZE NO. SHAFT DIA. SIZE NO. 1/2 = 10811 1-1/8 = 10814 3/4 = 10812 1-3/4 = 10815 7/8 = 10813 To order specify: Hub Size, Hole Pattern Orientation, and Hole Pattern Number. HOLE PATTERN Select proper 4 digit number from matrix on 10-7 & 10-8. NOTES: 1) Hub Adaptor must be used with -PK Rod End on series 1-8000 Multi-Motion Actuators, -H option on Non-Rotating Rod Cylinders, and -K Shaft on Series 1-8000 Rotary Actuators. 2) Hub adaptor kit includes all hardware to...

MATRIX: HUB ADAPTORS-IMPERIAL UNITS PRIMARY UNIT PHD UNIT MOUNTING HOLE PATTERN LOCATION 10811 10812 1-1/8" BORE 10815 10814 1-3/8" BORE NON-ROTATING NON-ROTATING 5-6000 ROTARY 7-8000 ROTARY 10813 ROD CYLINDER ROD CYLINDER & MULTI& MULTI1-2000 ROTARY 3-4000 MULTI- 3-4000 ROTARY MOTION MOTION ACTUATORS & MULTIACTUATORS ACTUATORS MOTION MOTION ACTUATOR ACTUATOR (SURFACE PERPENDICULAR TO TOOL PLATE POS. #3) ADAPTORS, TRANSITION BLANK HUB ADAPTOR FOR CUSTOMER TOOLING NOTE: For shaded areas or units not listed, see page 10-9 to see if required mounting pattern is available. If not, consult PHD....

MATRIX: HUB ADAPTORS-IMPERIAL UNITS PRIMARY UNIT PHD UNIT MOUNTING HOLE PATTERN LOCATION 10811 10812 1-1/8" BORE 10814 10815 1-3/8" BORE NON-ROTATING NON-ROTATING 5-6000 ROTARY 7-8000 ROTARY 10813 ROD CYLINDER ROD CYLINDER & MULTI& MULTI3-4000 ROTARY 1-2000 ROTARY 3-4000 MULTIMOTION MOTION ACTUATORS & MULTIACTUATORS ACTUATORS MOTION MOTION ACTUATOR ACTUATOR SHAFT DIAMETER FRONT & BACK ROTARY ACTUATORS FRONT & BACK BLANK HUB ADAPTOR FOR CUSTOMER TOOLING TOP & BOTTOM (PERP. TO SHAFT POS. #1 & #3) ADAPTORS, TRANSITION NOTES: 1) For shaded areas or units not listed, see page 10-9 to see if...

C 2X THREADED HOLE FOR J SET SCREW G 4X L THRU DIA & C’SINK FOR K FLAT HEAD CAP SCREW F NOTES: 1) EACH HUB ADAPTOR KIT CONTAINS ALL HARDWARE REQUIRED TO MOUNT COMPONENTS TOGETHER 2) ALL MOUNTING PATTERNS ARE CENTERED ON CENTERLINE AND SHAFT EXCEPT WHERE NOTED 3) 2 HOLE PATTERNS ON HORIZONTAL CENTERLINE OF HUB 4) SEE CHART BELOW FOR AVAILABLE PATTERNS FOR EACH HUB SIZE. IF DESIRED PATTERN IS NOT IN CHARTS, CONSULT PHD FOR AVAILABILITY MOUNTING HOLE PATTERN DIMENSIONS LETTER DIMENSIONS M ØL — — 2.750 .406 THRU 1.750 .344 THRU 2.125 3/8-16 UNC THRU 3.375 3/8-16 UNC THRU 1.750 5/16-18 UNC x...

ORDERING DATA: MINIATURE ADAPTORS FOR USE WITH PHD MINIATURE GRIPPERS, MINIATURE MULTI-MOTION ACTUATORS, SERIES 018050 & 018075 ROTARY ACTUATORS, AND SMALL SLIDES. To order, choose the proper Adaptor Kit from the matrix on page 10-11 to 10-13. The shaft that the Adaptor is to be mounted on must be a Plain Rod End or Standard Keyed Shaft. Adaptor Kit includes all hardware to mount the adaptor and component to the shaft. NOTE: Miniature Adaptors are designed for mounting to the bottom surface of the component. For mounting in other orientations or surfaces, consult PHD. Miniature Adaptors...

ADAPTORS, TRANSITION SAx108 BOTTOM SBx108 BOTTOM SAx110 BOTTOM SBx110 BOTTOM (IMPERIAL SHAFTS TO IMPERIAL UNITS) 19002 BOTTOM & SIDE 19x6x BOTTOM & SIDE 19012 BOTTOM & SIDE 19x7x BOTTOM & SIDE 19022 BOTTOM 19x8x BOTTOM 19022 SIDE 19x8x SIDE 19032 BOTTOM 19x9x BOTTOM 19032 SIDE 19x9x SIDE 53308-04 8400 BOTTOM & SIDE 8410 BOTTOM & SIDE SHAFT DIAMETER NOTES: FOR SHADED AREAS OR FOR UNITS NOT LISTED, CONSULT PHD FOR AVAILABILITY. SLIDES ROTARIES MATRIX: MINIATURE ADAPTORS-IMPERIAL SHAFT & IMPERIAL UNIT

ADAPTORS, TRANSITION NOTE: FOR SHADED AREAS OR FOR UNITS NOT LISTED, CONSULT PHD FOR AVAILABILITY. 8402 BOTTOM 8422 BOTTOM 19002 BOTTOM & SIDE 19x6x BOTTOM & SIDE 19012 BOTTOM & SIDE 19x7x BOTTOM & SIDE 19022 BOTTOM 19x8x BOTTOM 19022 SIDE 19x8x SIDE 19032 BOTTOM 19x9x BOTTOM 19032 SIDE 19x9x SIDE SHAFT DIAMETER PRIMARY UNIT (IMPERIAL SHAFTS TO METRIC UNIT) MATRIX: MINIATURE ADAPTORS-IMPERIAL SHAFT & METRIC UNIT