Toll Free: 87 PERMATEX (877-376-2839) 10 Columbus Blvd., Hartford, Connecticut 06106 6875 Parkland Boulevard, Solon Ohio 44139 Technical Data Sheet Permatex Ultra Synthetic® Gasket Maker AAM Revised 03/15 PRODUCT DESCRIPTION Permatex Ultra Synthetic Gasket Maker is designed to provide resistance to synthetic oils. It is a single component, room temperature, vulcanizing, gasketing compound designed to provide reliable “formed-in-place” gaskets for mechanical assemblies. Permatex Ultra Synthetic Gasket Maker cures on exposure to moisture in the air to form a tough, flexible, silicone rubber gasket which resists aging, weathering, and thermal cycling without hardening, shrinking or cracking. PRODUCT BENEFITS Resistance to synthetic oils Sensor safe, non-corrosive Good adhesion and flexibility Replaces most cut gaskets Can be used as a gasket maker or dressing Non-flammable, Non-toxic Valve covers Timing gear covers Intake manifold end seals DIRECTIONS FOR USE For assembly as a form-in-place gasket 1. Remove all previous material from mating surfaces. ® Permatex RTV Silicone Dissolver is recommended for removing cured silicones on most materials. It is not recommended for use on plastics or painted surfaces. 2. For best results, clean and dry all surfaces with a ® residue-free solvent, such as Permatex Brake and Parts Cleaner 3. Cut nozzle to desired bead size, 1/16” to 1/4” in diameter. A 1/8” bead is usually sufficient for most applications. 4. Remove cap, puncture tube or cartridge seal and attach extension nozzle. 5. Apply a continuous and even bead of silicone to one surface, first tracing the internal areas of the gasket configuration, then all surrounding bolt holes as shown: Assemble parts immediately while silicone is still wet. Finger tighten flange only until material begins to seep out the sides of the flange. Let dry for one hour and then secure or tighten to recommended torque specs. For best results, allow to cure overnight. Re-torque will not be necessary after the product has cured. Allow 24 hours for product to fully cure before filling with fluids or returning to service. For assembly as a gasket dressing 1. Repeat steps 1 through 4 as in previous section. 2. Apply a thin film of silicone to one surface to be sealed. 3. Place the pre-cut gasket onto silicone film. 4. Apply a second thin film to pre-cut gasket surface. 5. Remove any excess and assemble parts immediately. Note: Product is not recommended for use as a cylinder head gasket or head gasket sealant. Storage of Unused Product 1. Create a “Silicone Plug” by allowing excess material to extend beyond the extension nozzle sealing and protecting the remaining product from moisture. For reuse, simply remove the cured product from the tip. For Cleanup 1. Remove uncured product from parts and hand-tools with ® ® ® Permatex Fast Orange Wipes or Fast Orange Hand Cleaners. If skinned over, break film with a dry cloth to remove as much as possible. Remove the remaining ® material with Permatex RTV Silicone Dissolver. ® 2. Clean hands with a dry cloth or Permatex Fast Orange Hand Cleaner. NOT FOR PRODUCT SPECIFICATIONS. THE TECHNICAL DATA CONTAINED HEREIN ARE INTENDED AS REFERENCE ONLY. PLEASE CONTACT PERMATEX, INC., TECHNICAL SERVICE DEPARTMENT FOR ASSISTANCE AND RECOMMENDATIONS FOR YOUR SPECIFIC APPLICATION. PERMATEX, INC., HARTFORD SQUARE NORTH, 10 COLUMBUS BOULEVARD, HARTFORD, CT 06106 PHONE – (1-87PERMATEX)

Technical Data Sheet Ultra Synthetic Gasket Maker PROPERTIES OF UNCURED MATERIAL Chemical Type Appearance Odor Specific Gravity, g/ml Viscosity Extrusion rate @ 25C, (grams/min) Flash Point C (F) Typical Value Oxime silicone Dark Black Low Odor 1.42 Thixotropic paste 500 >93 (>200) incidental damages of any kind, including lost profits. This product may be covered by one or more United States or foreign patents or patent applications. TYPICAL CURING PERFORMANCE Permatex Ultra Synthetic Gasket Maker cures on exposure to moisture in the air. The product dries tack free in two hours and fully cures...