Permatex® Plastic Bond
2Pages

Toll Free: 87 PERMATEX (877-376-2839) 10 Columbus Blvd., Hartford, Connecticut 06106 6875 Parkland Boulevard, Solon Ohio 44139 PRODUCT DESCRIPTION Permatex Fuel Tank Repair is a two part, hand kneadable, putty type epoxy stick used for repairing metal gas tanks and containers. Contrasting colored materials are mixed together to form a uniform color to indicate thorough mixing. The resulting cured adhesive can be drilled, sanded, threaded or filed and it is resistant to fuels and most solvents after full cure. Note: Permatex Fuel Tank Repair is not intended for repairing Polyethylene and Propylene tanks or for structural bonding. PRODUCT BENEFITS Easy To Use: No heating required Applies and shapes like putty Technical Data Sheet Permatex Fuel Tank Repair AAM Revised 03/14 Cleanup must be completed before curing is complete. Use acetone or mineral spirits for cleanup. Clean hands with Permatex Fast Orange hand cleaner. PROPERTIES OF UNCURED MATERIAL Chemical Type Appearance Odor Specific Gravity (mixed) Flash Point, TCC, F Mix Ratio Typical Value Epoxy and Amine resins Brown outside, Grey inside Slight amine 1.5 g/ml >200 1:1 TYPICAL CURING PERFORMANCE Permatex Fuel Tank Repair sets up in 1 hour, can be machined in 5 hours, and fully cures in 24 hours. Fast and Reliable: Holds in 1 hour Can be machined within 5 hours Full cure in 24 hours Withstands moderate temperatures No shrinkage Resistant to most solvents, including ethanol TYPICAL ENVIRONMENTAL RESISTANCE Typical Values Temperature Resistance Safe To Use: Non-flammable No VOC’s GENERAL INFORMATION This product is not recommended for use in pure oxygen and/or oxygen rich systems and should not be selected as an adhesive for chlorine or other strong oxidizing materials. DIRECTIONS FOR USE 1. Before starting, make sure your work area is protected from accidental spills. Surfaces must be clean, dry and free of grease, oil, and excess debris. 2. Roughen smooth surfaces to be repaired with sandpaper. 3. Before handling the epoxy stick, place impermeable gloves on hands. Cut off required amount of epoxy and knead with fingers to a uniform color. This should take no longer than two minutes. 4. Apply to the surface to be repaired. Force into cracks or holes to be filled. Excess material can be removed, before it is cured, with a tool wetted with clean water. Also, for a smooth surface, hand rub with water or a damp cloth before the epoxy hardens. 5. On wet or damp surfaces, work material into area forcefully and hold in place until adhesion begins. Do not hold in place with hands, as heat is given off during cure. 6. After 1 hour, the epoxy will harden. 7. After 5 hours, the material can be machined. For Cleanup Continuous, F Maximum Intermittent, F Maximum Chemical / Solvent Resistance The product retains effective properties when in contact with water, oil, fuels, and solvents. For safe handling information on this product, consult the Material Safety Data Sheet, (MSDS). ORDERING INFORMATION Part Number 84334 Container Size 1 oz. Permatex Fuel Tank Repair Stick, w/vial, carded STORAGE Products shall be ideally stored in a cool, dry location in unopened containers at a temperature between 8C and 28C (46F and 82F) unless otherwise labeled. Optimal storage is at the lower half of this temperature range. To prevent contamination of unused product, do not return any material to its original container. NOTE The data contained herein are furnished for information only and are believed to be reliable. We cannot assume responsibility for the results obtained by others over whose NOT FOR PRODUCT SPECIFICATIONS. THE TECHNICAL DATA CONTAINED HEREIN ARE INTENDED AS REFERENCE ONLY. PLEASE CONTACT PERMATEX, INC., TECHNICAL SERVICE DEPARTMENT FOR ASSISTANCE AND RECOMMENDATIONS FOR YOUR SPECIFIC APPLICATION. PERMATEX, INC., HARTFORD SQUARE NORTH, 10 COLUMBUS BOULEVARD, HARTFORD, CT 06106 PHONE – (1-87PERMATEX)

Technical Data Sheet Permatex Fuel Tank Repair methods we have no control. Permatex, Inc. specifically disclaims all warranties expressed or implied, including warranties of merchantability or fitness for a particular purpose, arising from sale or use of Permatex, inc. products and disclaims any liability for consequential or incidental damages of any kind, including lost profits. This product may be covered by one or more United States or foreign patents or patent applications. Permatex and Fast Orange are trademarks of Permatex, Inc. © 2014 All rights reserved