SS 416
24Pages

Catalog excerpts

FASTENERS FOR USE IN STAINLESS STEEL SHEETS

FASTENERS FOR USE IN STAINLESS STEEL SHEETS One of the very basics of self-clinching is that the fastener must always be harder than the host sheet to ensure proper and permanent installation. This is particularly challenging when installing fasteners into stainless steel sheets. Therefore we have developed this line of specially hardened stainless steel fasteners for installation into stainless steel. Refer to “Dos and Don’ts” on page 24 for further information. Fasteners made from precipitation hardened grade stainless including A286 stainless are particularly useful in applications such...

Open the catalog to page 2

FASTENERS FOR USE IN STAINLESS STEEL SHEETS TYPE SP™ PEM 300® SELF-CLINCHING NUTS • After installation, reverse side of sheet remains flush and smooth. • For use in stainless steel sheets HRB 90 / HB 192 or less. • Corrosion resistance similar to 300 series stainless steel. PART NUMBER DESIGNATION Thread Code Shank Code Clinching profile may vary. Thread Code Thread Size Hole Size In Sheet +.003 -.000 Min. Dist. HoleC/L To Edge (1) Hole Size In Sheet +0.08 Min. Dist. HoleC/L To Edge (1) Thread Code Thread Size x Pitch (1) To minimize sheet distortion and maximize product performance, use a...

Open the catalog to page 3

FASTENERS FOR USE IN STAINLESS STEEL SHEETS TYPE SMPP™ SELF-CLINCHING NUTS • • • • Installs into stainless steel sheets as thin as .025”/0.64mm. Corrosion resistance similar to 300 series stainless steel. Reduced outer dimensions and thinner sheet capabilities compared to Type SP thread sizes. Recommended for use in stainless steel sheets HRB 90 / HB 192 or less. NEW PART NUMBER DESIGNATION SMPP – 440 Type and Material Thread Code Clinching profile may vary. Type A Fastener Material Thread (Shank) Min. Sheet Hardened Stainless Steel Code Max. Thickness Hole Size In Sheet C E T +.003 –.000...

Open the catalog to page 4

FASTENERS FOR USE IN STAINLESS STEEL SHEETS TYPE A4™/LA4™ FLOATING SELF-CLINCHING FASTENERS • Speeds assembly by compensating for mating hole misalignment. • Permanent installation into stainless steel sheets as thin as .038”/0.97mm and greater. • Provides high torque-out and pushout resistance in stainless panels. • Type LA4 thread locking torque performance is equivalent to applicable NASM25027 specifications.(1) • For use in stainless steel sheets HRB 88 / HB 183 or less. SELF-LOCKING Threaded Top Elliptically Formed Clinching profile may vary. Clinching profile may vary. Float –...

Open the catalog to page 5

FASTENERS FOR USE IN STAINLESS STEEL SHEETS TYPE F4™ PEMSERT® SELF-CLINCHING FLUSH FASTENERS • Can be installed into sheets as thin as .060”/1.53mm. • Ideal for flush applications where a stainless steel sheet requires load-bearing threads. • Can be installed before bending and forming to provide strong threads while still remaining flat with no protrusions on either surface. • For use in stainless steel sheets HRB 88 / HB 183 or less. Profile for H PART NUMBER DESIGNATION F4 – 440 – 1 Thread Code Shank Code Clinching profile may vary. Thread Size Profile for -2, -3, -4, & -5 shank codes. A...

Open the catalog to page 6

FASTENERS FOR USE IN STAINLESS STEEL SHEETS TYPE SO4™ THRU-HOLE THREADED STANDOFFS • Ideal for stacking or spacing. • Installed with head flush with one surface of the mounting sheet. • For use in stainless steel sheets HRB 88 / HB 183 or less. GENERAL DIMENSIONAL DATA All dimensions are in inches. Location of PEM single “groove” trademark may vary. Thread Code UNIFIED Hole Size In Sheet +.003 -.000 Min. Dist. Hole C/ To Edge (1) Clinching profile may vary. Thread Code Thread Code METRIC PART NUMBER DESIGNATION Varies according to length. See length charts below. Length Code Hole Size In...

Open the catalog to page 7

FASTENERS FOR USE IN STAINLESS STEEL SHEETS TYPE BSO4™ BLIND THREADED STANDOFFS • Ideal for stacking or spacing. • Installed with closed end head flush with one surface of the mounting sheet. • For use in stainless steel sheets HRB 88 / HB 183 or less. GENERAL DIMENSIONAL DATA All dimensions are in inches. Location of PEM single “groove” trademark may vary. Thread Code Hole Size In Sheet +.003 -.000 Min. Dist. Hole C/ To Edge (1) Thread Code Hole Size In Sheet +0.08 Min. Dist. Hole C/ To Edge (1) PART NUMBER DESIGNATION BSO4 – 440 – 8 Thread Code Varies according to length. See length...

Open the catalog to page 8

FASTENERS FOR USE IN STAINLESS STEEL SHEETS TYPE TSO4™ STANDOFFS FOR INSTALLATION INTO ULTRA-THIN STAINLESS STEEL SHEETS Location of PEM single “groove” trademark may vary. • For installation into ultra-thin stainless steel sheets as thin as .025”/0.63mm. • Threads on barrel end eliminate the need for long screws. • For use in stainless steel sheets HRB 88 / HB 183 or less. GENERAL DIMENSIONAL DATA All dimensions are in inches. Thread Code Hole Size In Sheet +.003 -.000 L Clinching profile may vary. Min. Dist. Hole C/ To Edge Thread Code Hole Size In Sheet +0.08 Min. Dist. Hole C/ To Edge...

Open the catalog to page 9

FASTENERS FOR USE IN STAINLESS STEEL SHEETS TYPE FH4™/FHP™ FLUSH-HEAD STUDS • Permanent installation into stainless steel sheets as thin as .040”/1mm. • Type FHP offers highest corrosion resistance and ideal for medical, food service, and marine applications. • For use in stainless steel sheets HRB 92 / HB 202 or less. Look for the PEM “Dimple” trademark. Thread Code Length Code Clinching profile may vary. unthreaded length All dimensions are in inches. Thread Size Thread Type Code Length Code “L” ±.015 (Length code in 16ths of an inch) .250 Hole Size in Sheet +.003 -.000 Max. Hole in...

Open the catalog to page 10

FASTENERS FOR USE IN STAINLESS STEEL SHEETS TYPE SGPC™ SWAGING COLLAR STUDS • nstalls into sheets as thin as .024”/0.6mm. I • Can be used to attach dissimilar materials. • Can accommodate multiple panels as long as the total thickness does not exceed the maximum sheet thickness.(1) • Can be installed into most panel materials, including stainless steel. • Allows for close centerline-to-edge distance. L Look for the PEM “Dimple” trademark. PART NUMBER DESIGNATION SGPC – 632 – 8 H Thread Code Length Code S unthreaded length All dimensions are in inches. Thread Size Type ength Code “L” ±.015 L...

Open the catalog to page 11