Catalogs >
PENN Engineering >
Self-Clinching Cable Tie Mounts

Self-Clinching Cable Tie Mounts
6Pages

Catalog excerpts

SELF-CLINCHING TY-D® CABLE TIE-MOUNTS AND HOOKS BULLETIN TD 410

Reverse side of Type TD installed in sheet. TD-2 PennEngineering • www.pemnet.com PEM® TY-D® self-clinching tie-mounts and hooks provide secure attachment points for mounting wires to electronic chassis or enclosures. All TY-D hardware installs quickly and permanently without screws and eliminates the use of adhesives that typically fail over time and temperature cycling. Type TD™ mounts allow users to easily slide ties through the hardware’s “eye” for fast cable mounting. Type TDO™ hooks* enable users to attach, remove, and return tie-bundled wires to their mounting points when components...

Open the catalog to page 2

METRIC U N I F I E D Length Hole Size Height Min. Hole Min. Hole Type Profile Length L Sheet In Sheet A B C D E G Edge To Edge To (1) Code ±.003 Thickness +.002 -.001 ±.003 ±.006 ±.006 ±.006 ±.006 ±.006 Sheet Edge Sheet Edge K M TD 40 4 .121 .040 - .050 .250 x .125 .246 .055 .065 .160 .308 .150 .040 .147 TD 60 6 .184 .040 - .070 .312 x .187 .308 .075 .065 .205 .370 .180 .040 .196 TD 175 12 .371 .040 - .125 .500 x .375 .496 .130 .095 .360 .562 .285 .040 .262 Length Hole Size Height Min. Hole Min. Hole Type Profile Length L Sheet In Sheet A B C D E G Edge To Edge To (1) Code ±0.08 Thickness...

Open the catalog to page 3

METRIC U N I F I E D I L H E B D A G ØC K M Hole In Sheet J F 40 50 120 Profile Shown Actual Size. Type TDO opening orientation mark. Length Hole Size Height Min. Hole Min. Hole Type Profile Length L Sheet In Sheet A B ØC D E F G H I J Edge To Edge To (1) Code ±0.08 Thickness +0.05 –0.03 ±0.08 ±0.15 ±0.15 ±0.15 ±0.15 ±0.13 Nom. ± 0.25 ± 0.25 Nom. Sheet Edge Sheet Edge K M TDO 40 8 6.25 1.02 - 3.94 6.35 x 9.53 9.42 5.41 6.22 3.3 11 7.24 11.96 3.05 3.3 2.11 1.02 3.73 TDO 50 8 6.25 1.02 - 3.94 6.35 x 11.13 11.02 5.79 6.86 3.3 12.6 7.62 13.13 3.05 3.3 2.59 1.02 4.98 TDO 120 8 6.25 1.02 - 3.94...

Open the catalog to page 4

METRIC U N I F I E D METRIC U N I F I E D Test Sheet Material Cold-rolled Steel 5052-H34 Aluminum Part Number Cable Tie Screw Installation Pushout Pull Thru Hanging Load Installation Pushout Pull Thru Hanging Load (lbs.) (lbs.) (lbs.) (lbs.) (lbs.) (lbs.) (lbs.) (lbs.) Size TDO-40-8 #8 3000 105 70 145 2000 105 70 130 TDO-50-8 #10 3000 150 90 145 2000 130 90 130 TDO-120-8 1/4 3000 200 110 145 2000 145 110 130 Test Sheet Material Cold-rolled Steel 5052-H34 Aluminum Part Number Cable Tie Screw Installation Pushout Pull Thru Hanging Load Installation Pushout Pull Thru Hanging Load (kN) (N) (N)...

Open the catalog to page 5

METRIC U N I F I E D 1. Punch a properly sized rectangular mounting hole in the sheet. Do not perform any secondary operations such as deburring. 2. Place the fastener through the mounting hole and into the anvil. 3. With the punch and anvil surfaces parallel, apply a squeezing force until the bottom of the fastener becomes flush with the sheet. W ANVIL PUNCH G +.010” +0.25mm Min. L +.005” +0.13mm Min. flat length all sides NOTE: The punch must be large enough to cover the entire base of the fastener to ensure proper installation. Part W Anvil Part Punch Part Number ±.001 Number Number...

Open the catalog to page 6