Catalogs >
PENN Engineering >
Index 118

Index 118
8Pages

Catalog excerpts

PEM® brand fasteners utilize self-clinching, broaching, flaring, surface mount, bonding or weld technology to provide strong, reusable, and permanent threads and mounting points in thin sheet metal, P.C. board or other rigid materials. INDEX QUICK PRODUCT LOCATOR

Open the catalog to page 1

PEM® FASTENER IDENTIFICATION MARKS To help you identify genuine PEM® brand fasteners, most are marked by one of our trademarks or identifiers. Genuine PEM fasteners can only be purchased from one of our authorized worldwide distributors. For a complete listing of these distributors, check our web site: www.pemnet.com. Trademark PEM® Dimple CFHA, CFHC, CHA, CHC, FH, FH4, FHA, FHL, FHLS, FHP, FHS, FHX, HF109, HFG8, HFE, HFH, HFHB, HFHS, HFLH, HSCB, KFH, KSSB, MPP, PF10, PF30, PF31, PF32, PF50, PF51, PF52, PF60, PF61, PF62, PF11, PF11M, PF11MF, PF11MW, PF11PM, PF12, PF12M, PF12MF, PF12MW,...

Open the catalog to page 2

Self-clinching fasteners are pressed into sheet metal panels as this as .016” / 0.4 mm. Flare Mounted fasteners can be installed into almost any rigid type of panel. Broaching fasteners are pressed into P.C. board or other plastic materials as thin as .060” / 1.53 mm. VariMount® bonding fasteners are assemblies comprised of a standard PEM fastener mounted permanently into base plates. Surface Mounted fasteners on tape and reel are soldered to a PC board in the same way as other surface mount components. Weld nuts are designed specially to be welded into place. (Products are listed...

Open the catalog to page 3

Bulletin FH Studs are for installation into thin, harder, high-strength materials. SC Bulletin PF Heat sink mounting system. HSCB (screw), HSR (nut) and HSL (spring). HSCB PEM C.A.P.S.® Bulletin PF Colored Access Panel Screws with plastic cap. Key features include Phillips drive and MAThread® anti-cross threading feature. SC FM PF10 Flush-mounted panel screw components. N10 (nut), PR10 (retainer) and PS10 (screw). KF2, KFS2 Bulletin K Nuts, internally threaded, for mounting on P.C. boards. Bulletin K Flare-mounted standoffs for mounting on P.C. boards with greater pullout performance....

Open the catalog to page 4

PFC2, PFS2 Bulletin PF Spring-loaded panel fastener assembly for tool or hand operation. Bulletin PF Panel fastener assembly with Phillips recess for tool only operation. Bulletin PF & SS Panel fastener assembly for installation into stainless steel sheets with Phillips recess for tool only operation. Bulletin PF Low-cost panel fastener assembly with universal slot/Phillips recess for tool or hand operation. Bulletins K & PF Panel fastener assembly for mounting on P.C. boards. Bulletin LN PEMHEX® self-locking nuts with a nylon hexagonal element to provide a reusable prevailing torque thread...

Open the catalog to page 5

Bulletin K Surface mount panel fastener retainer that is used with Type PSHP screw. Bulletin K Surface mount R’ANGLE® fasteners provide strong re-usable threads at right angle to PC board. SMTSO, SMTSOB Bulletin K Surface mount spacers and nuts are available threaded and unthreaded. Bulletin K Surface mount standoffs that eliminate the need for attaching screws. Bulletin MPF microPEM® TackSert® pins designed to hold a top panel to a bottom panel by broaching into the bottom panel. B SO, SO4, SOA, SOS Bulletin SO Thru-hole threaded and unthreaded standoffs installed with their heads flush...

Open the catalog to page 6

SELF-CLINCHING FASTENER INSTALLATION DOS AND DON’TS “Dos” Do provide mounting hole of specified size for each fastener. Do install fastener into punch side of sheet. Do make certain that shank (or pilot) is within hole before applying installation force. Do apply squeezing force between parallel surfaces. Do apply sufficient force to totally embed clinching ring around entire circumference and to bring shoulder squarely in contact with sheet. For some fasteners, installation will be complete when the head is flush with the panel surface. “Don’ts” Don’t attempt to install a 300 series...

Open the catalog to page 7

PennEngineering offers a wide range of technical support assistance. Let us put our expertise to work for you. We can provide: Training ► On customer site group or individual training by a technical representative and/or PEM® factory personnel ► Tutorial materials on website Global Network of Engineering Representatives to: ► Provide local company liaison ► Provide application review/product selection ► Provide technical materials ► Provide on-site product training and new product updates ► Assist with quotations ► The representative nearest you can be found on our website. rep/distributor...

Open the catalog to page 8