STRIASOL HD 59 NF

Product catalog summary

Definition: STRIASOL HD 59 NF is a two-component, odorless, water-dilutable, semi-gloss epoxy paint.

Intended Uses: This paint is suitable for floors and walls in technical areas, agro-food production sites, parking lots, and other locations where solvent-based paints are unsuitable.

Properties: The paint is permeable to water vapor, antidust, and offers good mechanical and chemical resistance. It can be applied to concrete, galvanized steel, and previously painted surfaces. For anti-slip surfaces, additives or fillers are recommended.

Technical Data: The paint has a semi-gloss finish, with a mixing ratio of 76.50/23.50 by weight and 77/23 by volume. It has a specific gravity of 1.60 g/cm³ and a solids volume of 62%. The pot life is 1.5 hours at 20°C, and the theoretical coverage is 6.0 m²/kg.

Instructions: Surface preparation varies by material, with specific primers recommended for galvanized steel and concrete. The product should be stored at 20°C for 24 hours before application. Mixing involves combining the base and hardener, followed by dilution with water.

Application Conditions: The ambient temperature should be between 10°C and 30°C, with humidity not exceeding 80%. The substrate temperature must be above 10°C and 3°C above the dew point.

Drying/Overcoating Time: Drying times vary with temperature, with light traffic possible after 2-6 days and normal traffic after 4-14 days. Overcoating times range from 12 hours to 12 days.

Cleaning: Initial cleaning should occur after complete polymerization, typically 7 days at 20°C. Proper maintenance is essential for long-lasting performance.

Reports: The product has been tested for fire reaction, water permeability, and resistance to abrasion, shock, and chemicals.

Regulatory Specifications: Classified under AFNOR NFT 36 005, the product complies with VOC regulations, containing a maximum of 20 g/l.

Health and Safety: The flash point for both components is over 100°C. Refer to the safety data sheet for precautions.

Packaging: Available in kits of 5 kg and 20 kg, with specific weights for the base and hardener components.

Catalog excerpts

PEINTURES REVETEMENTS Page 1/3 Maestria [V PEINTURES & SYSTEMES DEFINITION Two-component epoxy paint, odorless, water-diluable, semi-gloss. INTENDED USES STRIASOL HD 59 NF is intended for the floors and walls of: - technical local, - agro-food production sites, - parking lots, It's use particularly recommended where solvent-based paints can not be used. -is permeable to water vapor, and antidust -has good mechanical properties and chemical resistance (consult our technical department) as well as a good resistance to abrasion. - galvanized steel or steel previously prepared and printed using a suitable primer layer, - old paintings (in any case: imperatively consult our technical services). Note: the properties of the film, apart from its appearance, are not affected by actinic radiation To obtain an antislippery surface or a nonskid surface it is necessary to use an additive or to sprinkle fillers on the surface , consult our Technical Department. TECHNICAL DATAS Dry film finish Colour(s) Number of components Mixing ratio by weight Mixing ratio by volume Specific gravity Solids weight Solids volume Induction time at 20°C Pot life of mixing Temperature of product for application Theoritical coverage Practical spreading rate Semi glossy According to colour cards SOL, RAL/AFNOR 2 5 minutes, before use 1h30 at 20°C 45 minutes at 30°C between 15 and 30 °C 6,0 m2/ kg soit 170 g / m2 Depends on the surface, the ambient conditions and the application equipment Water (12 a 15%) Pour toute autre information, visitez notre site internet : www.maestria.fr Contact : [email protected]

Open the catalog to page 1

PEINTURES REVETEMENTS Page 2/3 INSTRUCTIONSSurface preparation Galvanised Steel : After sweep blasting, apply a coat of EPODUX PRIMER 61-134 v01 depending on the painting schedule and the recommendations set forth in our technical data sheet. Concrete : in compliance with recommendations set forth in DTU 59-3 or DTU 54-1 concerning the preparation and quality of flooring before painting operations : dry surface, clean, polluant free, showing sufficient roughness to enable the coating adherence. Steel : After grease removal/cleaning operations, abrasive blast cleaning to Sa 2 1/2 (according to...

Open the catalog to page 2

PEINTURES REVETEMENTS Page 3/3 Store at 20°C, 24 hours before Ambient temperature Ambient humidity Substrate humidity Substrate temperature : Minimum : 10°C / Maximum : 30°C 80% maximum 4% maximum Must be greater than 10°C and 3°C above dew point in order to prevent condensation DRYING / OVERCOATING TIME PEINTURES & SYSTEMES Laboratoire Recherche & Developpement - Usine - Administration Z.I. -1, rue Denis Papin - 09100 PAMIERS - Tel. 05 61 67 97 40 - Fax : 05 61 67 05 47 Contact: [email protected] Site internet: www.maestria.fr La presente fiche descriptive a pour but d'informer notre clientele...

Open the catalog to page 3

STRIASOL HD 59 NF

STRIASOL HD 59 NF

Catalog excerpts

All PEINTURES MAESTRIA catalogs and technical brochures