Bands Technologies • 5 GHz: supports • WiFi • High TX output power of 23 dBm per path, 26 dBm total • IEEE 802.11ac compliant, supporting legacy 802.11a and 802.11n operating modes • 2x2 MU-MIMO with up to 867 Mbps data rate • Standard mini-PCI Express 1.1 interface • Standard mini-card form factor 30 mm x 50.95 mm

Industrial IoT Radio Module 2x2, 802.11ac Wave 2 The PCTEL RM-WIFI-AC-2X2-HP 802.11ac Wave 2 is a device built in a standard mini-card form factor and a standard mini-PCIe interface featuring true enterprise-class specifications with high TX output power and support for all 802.11ac channel definitions including 80 MHz channels. Low power consumption and a small form factor make this radio module ideal for integration into a wide variety of platforms.

^PCTEL Industrial loT Radio Module 2x2, 802.11ac Wave 2 PCTEL® RM-WIFI-AC-2x2-HP Integration Guide 2x2, 802.11ac Wave 2 Industrial IoT Radio Module Feature Benefit • 23 dBm per path with 2 RF paths (2 antennas). Note: The maximum power is set per specific channel and limited per specific regulations of each approved countries. See PCTEL for additional information.

Industrial IoT Radio Module 2x2, 802.11ac Wave 2 Transmit Power and Receive Sensitivity Data Rate / MCS Spatial Streams

^PCTEL Industrial loT Radio Module 2x2, 802.11ac Wave 2 In addition, two antenna cables are required. Important Note: For use as a client device, (not DFS master), the integrator can choose or specify a different antenna of like type and equal or lesser gain as an antenna appearing in the above table and still maintain compliance. Reference FCC Part 15.204(c) (4) for further information on this topic. Important Note: For use in a host system that is a DFS master, the minimum, net antenna gain allowed is 1.1 dBi, including all other cable loss. Any antenna/cable combination whose gain is lower...

Industrial IoT Radio Module 2x2, 802.11ac Wave 2 6.1.2. FCC Declaration of Conformity Statement These paragraphs must be included in any end-user documentation. This device complies with Part 15 rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. T his device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable...

^PCTELIndustrial loT Radio Module 2x2, 802.11ac Wave 2 3. Note that per FCC Part 15 rules pertaining to unlicensed transmitters, the host device must be equipped with a unique antenna connector. Compliance with 47 CFR 15.203 does not permit the use of standard connectors such as N, BNC, SMA, TNC, etc. 4. The modular transmitter has been tested to the following FCC rules: 5. The RM-WIFI-AC-2X2-HP-US radio module has been certified with the antennas listed in the table above. For use as a client device (DFS non-master), the integrator can choose or specify a different antenna of like type and equal...

^PCTEL Industrial loT Radio Module 2x2, 802.11ac Wave 2 The radio transmitter (IC: 26854-RMWIFIAC2X2) was approved by Innovation, Science and Economic Development (ISED) Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Le present emetteur radio (IC: 26854-RMWIFIAC2X2) a ete approuve par Innovation, Sciences et Developpement economique Canada pour fonctionner avec les types d'antenne...

Industrial IoT Radio Module 2x2, 802.11ac Wave 2 6.2.3. ISED Canada Radiation Exposure Statement These paragraphs must be included in any end-user documentation. This transmitter/receiver has been evaluated for RF exposure for humans in reference to ANSI C 95.1 (American National Standards Institute) limits. This evaluation was based on RSS-102 Rev 5. To maintain compliance, the minimum separation distance for RM-WIFI-AC-2X2-HP-CA is 7.87 inches (20 cm) from users or general bystanders. Further RF exposure reduction can be achieved if the product/antennas are kept as far as possible from the...

Industrial IoT Radio Module 2x2, 802.11ac Wave 2 9. The integrator or host manufacturer must not provide information to the end user regarding the installation or removal of this modular transmitter from the host device in the user’s manual of the end-product. 10. Any end-user manual shall include all required regulatory information/warnings as shown in this manual. 11. Even though the PCTEL RM-WIFI-AC-2X2-HP-CA radio module has been ISED certified, the host product (i.e., the integrated product of radio module + host device) needs to be evaluated for continued compliance in that specific configuration....

Industrial IoT Radio Module 2x2, 802.11ac Wave 2 11. Même si le module radio RM-WIFI-AC-2X2-HP-CA de PCTEL a été certifié ISDE, le produit hôte (à voire le produit intégré du module radio + le dispositif hôte) doit être évalué pour une conformité continue dans cette configuration spécifique. Veuillez contacter PCTEL pour obtenir les outils nécessaires à une telle évaluation. 12. Si l’une de ces conditions ne peut pas être remplie (par exemple en utilisant un type d’antenne unique), la certification ISDE ne sera plus considérée comme valide, et le numéro IC ne pourra pas être utilisé sur le produit...

^PCTEL Industrial loT Radio Module 2x2, 802.11ac Wave 2 This radio transmitter has been approved under RED 2014/53/EU to operate the antenna types listed below with the maximum gain indicated. The usage of different antennas in the final host device may need a new assessment of host conformity to RED 2014/53/EU. Table 3. Approved Antennas In addition, two antenna cables are required. 6.3.3. European Union and UK Radiation Exposure Statement This radio transmitter has been evaluated for RF exposure for humans in reference to ICNIRP (International Commission on NonIonizing Radiation Protection)...