Series 686B Smart Vibration Switch Reliable Electronic Vibration Switch Protection At the Low Price of a Mechanical Switch!!!! Highlights n A IMI S n en Indus sors Exclu try sive! Fully USB programmable Solid state relay for reliable operation Monitors vibration velocity for consistent results Photo courtesy of Midwest Towers, Inc. 2-wire operation uses existing switch wires Remote Reset AnywhereTM for safety and convenience Exclusive MAVTTM sets alarm threshold automatically Eliminates false trips with programmable delays Hazardous area approvals The All New Electronic Smart Vibration Switch from IMI Sensors is highly versatile, fully user programmable via USB, low cost, and a drop-in replacement for most popular mechanical vibration switches. The Smart Vibration Switch includes an embedded piezoelectric accelerometer for accurate measurement, monitors vibration velocity for more consistent results, and provides the reliability not found in mechanical switches. It’s also a significantly lower cost alternative for many electronic vibration switch applications requiring single relay operation. Cooling tower fans & gearboxes Motors & pumps Series 686B (US Patent Pending) Get Smart and replace your troublesome mechanical vibration switches with the economical, electronic Smart Vibration Switch today!

Replaces Mechanical and Electronic Vibration Switches Model 686B01 Smart Vibration Switch with 2-pin MIL Connector Model 686B11 Smart Vibration Switch with Integral Cable Models EP686B7X & EX686B7X Smart Vibration Switch with Explosion Proof Condulet Enclosure Comparison of Mechanical Vibration Switches to the IMI Sensors Smart Vibration Switch Model 686B7X Smart Vibration Switch with Terminal Block Connector The Versatile Smart Vibration Switch The New Series 686B Smart Vibration Switch is now fully USB programmable and more costeffective than ever. With two-wire operation, universal power,...

Fully USB Programmable from any PC The Smart Vibration Switch is fully user programmable using eitherthe Model 600A15 orBOOMB USB Switch Programmer Kit (optional). See the "Specifications and Ordering Information" on page 5 for details. These kits can be used in conjunction with any PC to read or reprogram the settings of the Smart Vibration Switch. The user can enable/disable and set the following switch parameters. Alarm threshold level & hysteresis Power-on, startup, & operating delays Normally open or normally closed Residual vibration leve Tod*yu \V*d»ldary, April 0-1, 1009 DPEHA1I0NAL DELAY...

Specifications and Ordering Information Model 686B01 Series 686B Smart Vibration Switch Specifications Performance Alarm Threshold Level Frequency Range (±3 dB) Alarm Threshold Hysteresis Residual Vibration Level (Reference) Residual Vibration Level (Level) 0.25 to 5.0 in/sec pk 4.5 to 90.0 mm/sec rms 180 to 60k cpm 3 to 1000 Hz 3, 6, or 10% Dependent or Independent of alarm threshold 1 to 40% of alarm threshold level MAVTTM Transverse Sensitivity Power On Delay Startup Delay (Active) Startup Delay (Time) Startup Delay (x Alarm Threshold) Operational (alarm) Delay AC/DC POLARITY INDEPENDENT Relay...

Specifications and Ordering Information EX Models - For Hazardous Locations EX Models - For Hazardous Locations CSA: Class I, Div. 2, Groups A,B,C, D Ex nL IIC T3 AEx nA IIC T3 INMETRO: Ex ic IIC T3 Gc -54 ºC ≤ Ta ≤ +85 ºC CSA: Class I, Div. 2, Groups A,B,C, D Ex nA IIC T3 AEx nA IIC T3 INMETRO: Ex ic IIC T3 Gc -54 ºC ≤ Ta ≤ +85 ºC ATEX/IECEx: Ex d IIC T3 Gb -20 ºC ≤ Ta ≤ +85 ºC Voltage Rating Current Rating Mounting Thread Electrical Connection Cable Length Cable Type 10 to 30 VDC 10 to 30 VDC 100 mA 100 mA 1/4-28 UNF-2B (Female) 1/4-28 UNF-2B (Female) Molded Integral Cable Integral Armord Cable...

Typical Smart Vibration Switch Installation Basic Installation Installation for Use with an External Relay This is a typical installation for use with a pilot/indicator light (or other load) where the current is ≤500 mA. No reset switch is required since the Smart Vibration Switch is set to NL (Non-Latching). This is a typical installation for use with an external SPDT or DPDT relay (see page 8 for relay selections). This configuration is used when the load requires >500 mA or when using a DPDT relay to switch two circuits using a single Smart Vibration Switch. The switching can be normally open,...

Ordering Guide Switch Model Number Template Cable Length Hazardous Approvals Explosion Proof Condulet Enclosure Metric Installation (Not With EP or EX with Terminal Block) Metric EX Approved (Not With Terminal Block Connection No Prefix Option (Specify only if Electrical Connection is 1 or 6) Leave blank for default length of 10’ (3m) Enter integral cable length, e.g., for 150 ft enter 150; for 8 meters enter 008 Electrical Connection Cable Termination or Connector (others available) 2-Pin Mil-C-5015 Integral Cable (Model 052) Integral Armored Cable (Model 047) Terminal Block Program Configuration...

Machine Protection Products Protect Your Valuable Machinery with Exclusive Products From IMI Model 649A01 Reciprocating Machinery Protector Model 682A05 Bearing Fault Detector The RMP is a 4-20 mA transmitter that protects reciprocating compressors 24/7 against serious faults that can cause catastrophic failures quickly. Using patented techniques, it out performs traditional Impact Transmitters. The BFD is a vibration transmitter that provides early warning of typical rolling element bearing faults such as cracked races, spalling, brinelling, looseness, and loss of lubrication; even in slow speed...