LOGO.pro - Product Information
12Pages

LOGO.pro PRODUCT INFORMATION

LOGO.pro Optimised working with one-sided anchor technology LOGO.pro‘s one-sided anchor technology means that the tie points can be operated by just one person. This not only makes optimised working with low manpower requirements possible, but also facilitates working in confined spaces. One-sided anchor technology makes the formwork anchors easy to operate by just one person. Innovative addition to the LOGO range This new wall formwork consists of a profiled, high-strength flat steel frame and it provides the same robustness and reliability as the familiar LOGO.3 wall formwork. As usual...

Conventional anchoring guide bushings LOGO.pro can be used variably with regard to anchor technology. Anchoring is done conventionally with guide bushings on both sides of the formwork. Standard material can be used for both anchor variants, no cost-intensive, conical anchors.. Delivery condition with guide bushings in all panels: The tie rod (DW15 or DW20) with tube and plate with ball and-socket-joint on both sides can be used immediately in the conventional way. One-sided anchoring guide bushing clamping unit Conversion of the outer formwork with clamping unit: The tie rod with tube,...

Parts list (Elements) Outside corner post 50 x 50 x 340 cm 179.506.0500 205.40 kg Inside corner post 25 x 25 x 340 cm 179.505.0250 80.60 kg Panel 75 x 340 cm Art.-No. 179.501.0750 Weight 151.00 kg Large-size panel 240 x 340 cm Art.-No. 179.501.2400 Weight 453.20 kg

Part list (Elements) Outside corner post 50 x 50 x 270 cm 176.506.0500 166.00 kg Inside corner post 25 x 25 x 270 cm 176.505.0250 63.00 kg Panel 75 x 270 cm Art.-No. 176.501.0750 Weight 130.00 kg Large-size panel 240 x 270 cm Art.-No. 176.501.2400 Weight 364.00 kg

Part list (Accessories) Art.-No. PRO clamping unit DW20 mount. PRO clamping unit DW15 mount. PRO guide bushing mount. (hole for DW15 / DW20)

For single-sided anchoring, the tie rod together with the tube, the guide bushing and plate with ball-andsocket joint are turned into the clamping unit of the outer formwork. Unscrew the tie rod with the plate with ball-andsocket joint during dismantling. Perfect concrete surface Formwork offsets are possible due to the rotatable support of the locking nut in the clamping unit. Have you already seen it? We present both anchoring systems for the new LOGO.pro formwork system in our new application video. Changing between these systems is a very simple operation. D ( 1:1 )

One-sided anchoring with PASCHAL - it‘s that easy Simple operation thanks to interchange technology PASCHAL has developed a new wall formwork that can be easily converted from two-sided to one-sided anchoring thanks to a smart changing system. No further special parts are required. With the new LOGO.pro wall formwork, the medium-sized formwork manufacturer PASCHAL is completing its formwork range at the top end. The technical data correspond as far as possible to LOGO.3 - with one decisive difference: Depending on requirements, LOGO.pro can be anchored not only from both sides but also...

No special parts required Unlike other manufacturers, PASCHAL does not rely on conical tie rods and complicated fitting methods. Instead, LOGO. pro uses conventional DYWIDAG tie rods. Accordingly, the PVC-tubes or fibreconcrete tubes can be freely selected as cladding tubes up to 50 mm diameter. Compared to one-sided anchored formwork systems using conical anchors, the use of cost-effective standard components not only leads to simpler and thus faster work sequences, but also avoids potential problems that can arise in terms of material storage or loss of special parts. Thus LOGO.pro offers...

Conversion to one-sided handling For one-sided operation of the formwork anchors, the guide bushings in the outer formwork can be replaced by clamping units in just a few steps. 1. Remove the guide bushing (outer formwork) Turn the guide bushing by 80° with the assembly tool Turn the ring bolt by 90° T12.001.05.pdf Extract the guide bushing with the assembly tool T12.003.02.pdf T12.001.07.pdf 2. Mount the clamping unit Insert the clamping unit T12.001.08.pdf Turn the ring bolt by 90° Turn the clamping unit by 80° with the assembly too 3. Remove the guide bushing (inner formwork) Turn the...

4. Feed the tie rod Feed the tie rod, tube, guide bushing and plate with ball-and-socket joint through the inner formwork 5. Turn the tie rod Turn the tie rod by hand or with the tie rod spanner 6 cm deep into the clamping unit of the outer formwork 6. Lock the guide bushing in the panel of the inner formwork Turn the ring bolt by 90° Turn the guide bushing by 80° with the assembly tool 7. Tighten the plate with ball-and-socket joint Tighten firmly the plate with balland-socket joint

PASCHAL-Werk G. Maier GmbH · Kreuzbühlstraße 5 · 77790 Steinach · Germany Phone +49 7832 71-0 · Fax +49 7832 71-209 · service@paschal.com · pascha