aerospace climate control electromechanical ltration uid & gas handling hydraulics pneumatics process control sealing & shielding Pneumatic Rotary Actuators & Airmotors Catalogue PDE2613TCUK May 2012

PDE2613TCUK Pneumatic Rotary Actuators & Airmotors 6 Parker Hannifin Corporation Pneumatic Division - Europe

PDE2613TCUK Stainless Steel Air Motors - P1V-S Pneumatic Rotary Actuators & Airmotors A Stainless Steel Air Motors P1V-S Series 7 Parker Hannifin Corporation Pneumatic Division - Europe

PDE2613TCUK Stainless Steel Air Motors - P1V-S Pneumatic Rotary Actuators & Airmotors A Lubrication-free vanes for intermittent operation as standard. Fluor rubber O-ring Planetary gear Compressed air connection Outlet Fluor rubber seal Polished stainless housing Hardened stainless output shaft Stainless steel air motors, P1V-S Series P1V-S is a range of air motors with all external components made of stainless steel, which means that they can be used in food grade applications, and in all other applications where there is a risk of corrosion. The range contains seven different sizes, with powers...

PDE2613TCUK Stainless Steel Air Motors - P1V-S Pneumatic Rotary Actuators & Airmotors Principles of motor operation Torque, power and air consumption graphs The performance characteristics of each motor are shown in M [%] Q [%], P [%] Inlet Outlet Inlet, left Residual outlet Inlet, right n [%] Outlet The curve is for 6 bar P = power Q = air consumption M = torque n = speed Outlet 1 2 3 4 Rotor cylinder Rotor Vanes End piece with bearing Possible working range of motor. Optimum working range of motor. Higher speeds = more vane wear Lower speeds with high torque = more gearbox wear There are a...

PDE2613TCUK Stainless Steel Air Motors - P1V-S Pneumatic Rotary Actuators & Airmotors Correction diagram A power will not be obtained. Correction factor Supply throttling, nonreversible motor. Outlet throttling. Supply throttling, reversible motor. Torque curve change caused by throttling. P = power M = torque Pressure regulation at motor inlet. Q = air consumption n = speed All catalogue data and curves are specified at a supply pressure of 6 bar (in the inlet port). This diagram shows the effect of pressure on speed, torque, power and air consumption. Start off on the curve at the pressure...

PDE2613TCUK Stainless Steel Air Motors - P1V-S Pneumatic Rotary Actuators & Airmotors Air supply The table can be used as follows: The air supplying the motor must be filtered and regulated. 3 2 1 Shut-off, filtering, pressure regulation and control valve If you are using only one motor with each air treatment unit and valve, simply follow the table. If you are using more than one motor with the same air treatment unit: read the table values for selecting the air treatment unit and add them together, and select a suitable air treatment unit from the table showing air flows per treatment unit....

PDE2613TCUK Stainless Steel Air Motors - P1V-S Pneumatic Rotary Actuators & Airmotors Air motors A P1V-S002 P1V-S008 P1V-S012 P1V-S020 P1V-S030 P1V-S060 Air flow required, Nl/s Air motor 1,7 3,8 5,0 6,3 8,0 14,5 27 Air flow required, Nl/min 102 230 300 380 480 870 1620 4 4 6 10 10 12 19 Min. internal diameter of pipe, mm P1V-S120 Choice of air treatment unit: recommended min. air flow in litres/minute at 7,5 bar air supply and 0,8 bar pressure drop 110 255 330 420 530 960 1780 Choice of valve: recommended min. air flow in Qn in litres/minute (Qn is the flow through the valve at 6 bar supply pressure...

PDE2613TCUK Stainless Steel Air Motors - P1V-S Pneumatic Rotary Actuators & Airmotors Silencing Outlet silencer Compressed air quality Central silencer The noise from an air motor consists of both mechanical noise and a pulsating noise from the air flowing out of the ­ utlet. The installation of o the motor has a considerable effect on mechanical noise. It should be installed so that no mechanical resonance effects occur. The ­ utlet air o creates a noise level which can amount to 108 dB(A) if the air is allowed to exhaust freely into the atmosphere. To reduce noise levels, various types of outlet...

PDE2613TCUK Stainless Steel Air Motors - P1V-S Pneumatic Rotary Actuators & Airmotors Service interval CE marking The air motors are supplied as “Components for installation” – the installer is responsible for ensuring that the motors are installed safely in the overall system. Parker Pneumatic guarantees that its products are safe, and as a supplier of pneumatic equipment we ensure that the equipment is designed and manufactured in accordance with the applicable EU directive. Most of our products are classed as components as defined by various directives, and although we guarantee that the components...

PDE2613TCUK Stainless Steel Air Motors - P1V-S Pneumatic Rotary Actuators & Airmotors Choice of air motor Torque at maximum power [Nm] A Speed at maximum power [rpm] The motor to be used should be selected by starting with the torque needed at a specific shaft speed. In other words, to choose the right motor, you have to know the required speed and ­orque. Since maximum power is reached at half the t motor’s free ­ peed, the motor should be chosen so that the s oprating point is as close as possible to the maximum power of the motor. The design principle of the motor means that higher torque...

PDE2613TCUK Stainless Steel Air Motors - P1V-S Pneumatic Rotary Actuators & Airmotors Technical data Working pressure Working temperature Ambient temperature Medium Max 7 bar (max 6 bar in explosive atmospheres) -30 °C to +100 °C -20 °C to +40 °C in explosive atmospheres 40 µm filtered, oil mist or dry unlubricated compressed air Table and diagram data All values are typical values, with a tolerance of ±10% Option Other variants on request Material specification Planetary gearbox for: P1V-S060A0010 /30 /48 P1V-S120A0012 /32 Stainless steel, X46Cr13 Planetary gearbox for last planet stage incl....