aerospace climate control electromechanical ltration uid & gas handling hydraulics pneumatics process control sealing & shielding Pneumatic ISO Cylinders Series P1D-B According to ISO 15552 PDE2659TCUK June 2012

PDE2659TCUK P1D-B Pneumatic ISO Cylinders Anodised body extrusion. Polyurethane seals Magnetic pistons as standard. Surface treated steel end cover nuts. Adjustable cushioning. One piston rod nut according to ISO 68715 is included as standard. Stainless steel piston rod as standard. Hard chromed steel available as an option. Metal piston rod bearing Body extrusion with grooves for ”drop-in” sensors. All P1D-B cylinders for normal temperature have initial greasing of a transparent, non-toxic grease, approved by the food industry, which is entirely free from PTFE and silicone. Standard cylinders...

PDE2659TCUK P1D-B Pneumatic ISO Cylinders General technical data Product type Bore size Stroke length Versions P1D-B...MS Cushioning Position sensing Installation Mounting position Standard cylinder according to ISO 15552 32 - 125 mm 5-2800 mm Double acting Adjustable air cushioning Proximity sensor P1D cylinder and piston rod mountings Any Operating and environmental data Operating medium For best possible service life and trouble-free operation dry, filtered compressed air to ISO 8573-1:2010 quality class 3.4.3 should be used. This specifies a dew point of +3oC for indoor operation (a lower...

PDE2659TCUK P1D-B Pneumatic ISO Cylinders Cushioning characteristics The load is the sum of internal and external friction, plus any gravitational forces. At high relative load (pressure drop exceeding 1 bar), we recommend that for any given speed, the mass should be reduced by a factor of 2.5, or for a given mass, the speed should be reduced by a factor of 1.5. This is in relation to the maximum performance given in the diagram The diagram below is used for dimensioning of cylinders related to the cushioning capacity. The maximum cushioning capacity shown in the diagram assumes the following:...

PDE2659TCUK P1D-B Pneumatic ISO Cylinders Guide for selecting suitable tubing The selection of the correct size of tubing is often based on experience, with no great thought to optimizing energy efficiency and cylinder velocity. This is usually acceptable, but making a rough calculation can result in worthwhile economic gains. The following is the basic principle: The following prerequisites apply: 1. The primary line to the working valve could be over sized (this does not cause any extra air consumption and consequently does not create any extra costs in operation). 2. The tubes between the...

PDE2659TCUK P1D-B Pneumatic ISO Cylinders Example 1 : Which tube diameter should be used? Valve series with respective flows in Nl/minute A 50 mm bore cylinder is to be operated at 0.5 m/s. The tube length between the valve and cylinder is 2 m. In the diagram we follow the line from 50 mm bore to 0.5 m/s and get an “equivalent throttling bore“ of approximately 4 mm. We continue out to the right in the chart and intersect the line for a 2 m tube between the curves for 4 mm (6/4 tube) and 6 mm(8/6 tube). This means that a 6/4 tube throttles the velocity somewhat, while an 8/6 tube is a little too...

PDE2659TCUK P1D-B Pneumatic ISO Cylinders Order Key Code Order Key Code 15 digit order code 1 2 3 4 5 6 7 8 9 20 digit order code 10 11 12 13 14 15 P 1 D B 0 3 2 M S – 0 1 0 0 – 16 17 18 19 20 N D N N N Stroke (mm) e.g. 0100 = 100 mm Cylinder version B Basic Optional stroke lengths up to 2800 mm. Standard strokes see table page 9 Scraper Function Piston rod material Seals M Standard Double acting S Stainless steel Standard -20OC to +80OC C Cylinder bore mm Chrome plated steel Standard -20OC to +80OC 032 040 050 063 Cylinder mountings 080 90O 0O 90O = shaft square to, 0O shaft in line with ports5)...

PDE2659TCUK P1D-B Pneumatic ISO Cylinders Mountings Centre trunnion MT4 Intended for articulated mounting of cylinder. The trunnion is factory-fitted in the centre of the cylinder or at an optional location specified by the XV-measure - Combined with pivot bracket for MT4. Material: Trunnion: Zinc plated steel Trunnion with optional location The central trunnion for the P1D-B is ordered with letter G in position 17 and desired XV-measure (3-digit measure in mm) in positions 18-20. e.g. P1D-B100MS-0500NG300 Material: nodular graphite cast iron, passivated steel Cyl. bore Ø mm Weight kg Order code...

PDE2659TCUK P1D-B Pneumatic ISO Cylinders Sensors New drop-in sensors The P1D sensors can easily be installed from the side in the sensor groove, at any position along the piston stroke. The sensors are completely recessed and thus mechanically protected. Choose between electronic or reed sensors and several cable lengths and 8 mm and M12 con­ ectors. n The same standard sensors are used for all P1D versions. Electronic sensors Reed sensors The new electronic sensors are ”Solid State”, i.e. they have no moving parts at all. They are provided with short-circuit protection and transient protection...

PDE2659TCUK P1D-B Pneumatic ISO Cylinders Sensors Electronic sensors M8 M12 Signal +V DC Reed sensors – V DC – V DC M8 Signal M12 Signal –(+) V AC/ +(–) V AC/ + V DC DC DC –(+) V AC/ DC Signal +(–) V AC/ DC Brown Brown Black Black Blue Blue P8S-GCFPX Brown Blue P8S-GRFLX / P8S-GRFLX2 Brown Blue Dimensions Sensor Installation Sensors Insert sensor LED 20 Turn sensor Tighten screw Torque 0,20 ±0,05Nm Parker Hannifin Corporation Pneumatic Division - Europe

PDE2659TCUK P1D-B Pneumatic ISO Cylinders Sensors Ordering data Output/function Cable/connector Weight kg Order code Electronic sensors , 10-30 V DC PNP type, normally open PNP type, normally open PNP type, normally open PNP type, normally open 0,27 m PUR-cable and 8 mm snap-in male connector 0,27 m PUR-cable and M12 screw male connector 3 m PVC-cable without connector 10 m PVC-cable without connector 0,007 0,015 0,030 0,110 P8S-GPSHX P8S-GPMHX P8S-GPFLX P8S-GPFTX Reed sensors , 10-30 V AC/DC Normally open Normally open Normally open Normally open Normally closed 0,27 m PUR-cable and 8 mm snap-in...