OSPP-Classic
37Pages

OSPP-Classic ORIGA SYSTEM PLUS P-A4P027GB 05/2018

Contents Linear Drives The right to introduce technical modifications is reserved ORIGA SYSTEM PLUS Rodless Pneumatic Cylinder OSPP-Classic Basic Cylinder Characteristics Loads, Forces and Moments Mid-Section Permissible Support OSPP-C Dimensions, Stroke and Dead Length A Air Connection on the End-face Both Air Connections at One End Integrated 3/2 Way Valves VOE Order Instructions – Basic Cylinder Recirculating Ball Bearing Guide KF Loads, Forces and Moments Dimensions Series OSPP-C KF16 to KF50 Mid-Section Permissible Support OSPP-C KF Variable Stop Type VS16 to VS50 Shock Absorber...

Rodless Pneumatic Cylinder OSPP-Classic ø 16-80 mm Pressures quoted as gauge pressure Rodless cylinder Double-acting, with cushioning, position sensing capability Ambient temperature range Tmin Tmax Other temperature ranges on request Filtered, unlubricated compressed air (other media on request) Permanent grease lubrication (additional oil mist lubrication not required) Option: special slow speed grease Special Versions: • Stainless steel screws • Slow speed lubrication • Viton® seals • Air connection on the end-face • Both air connections on one end • Integrated Valves VOE Weight (mass)...

Loads, Forces and Moments Choice of cylinder is decided by: • Permissible loads, forces and moments • Performance of the pneumatic end cushions. The main factors here are the mass to be cushioned and the piston speed at start of cushioning (unless external cushioning is used, e. g. hydraulic shock absorbers). M = F ·l Bending moments are calculated from the centre of the linear actuator. The adjacent table shows the maximum values for light, shock-free operation, which must not be exceeded even in dynamic operation. max. Moments Theoretical Effective max. Load Cushion Action Force FA Action...

Permissible Support Spacings: OSPP16-C to 32-C Distance k Permissible Support Spacings: OSPP40-C to 80-C Mid-Section Supports To avoid excessive bending and oscillation of the cylinder, mid-section supports are required dependent on specified stroke lengths and applied loads. The diagrams show the maximum possible support spacings depending on the load. Bending up to max. 0.5 mm is permissible between supports. The midsection supports are clamped on to the dovetail profile of the cylinder tube. They are also able to take the axial forces. For types and dimensions see page 23. Parker...

Cylinder Stroke and Dead Length A Dimensions of Basic Cylinder OSPP16-C to 80-C A • Free choice of stroke length up to 6000 mm in 1 mm steps. • Longer strokes on request. Tandem Cylinder Two pistons are fitted: dimension "Z" is optional. (Please note minimum distance "Zmin"). • Free choice of stroke length up to 6000 mm in 1 mm steps. • Longer strokes on request. • Stroke length to order is stroke + dimension "Z". End Cap/Air Connection can be rotated 4 x 90° Series OSPP16-C to 80-C BY Please note: To avoid multiple actuation of magnetic switches, the second piston is not equipped with...

Cushion adjustment screw In some situations it is necessary or desirable to fit a special end cap with the air connection on the end-face instead of the standard end cap with the air connection on the side. The special end cap can also be rotated 4 x 90° to locate the cushion adjustment screw as desired. Supplied in pairs. Cushion adjustment screw Dimension Table [mm] Series Parker Hannifin Corporation Pneumatic Division - Europe

Series OSPP16-C Cushion adjustment screw A special end cap with both air connections on one side is available for situations where shortage of space, simplicity of installation or the nature of the process make it desirable. Air supply to the other end is via internal air passages (OSPP25-C to 80-C) or via a hollow aluminium profile fitted externally (OSPP16-C). In this case the end caps cannot be rotated. Cushion adjustment screw * Versions of air connection positions 1=>1 or 2=>2, the unused connection must be closed! Cushion adjustment screw The right to introduce technical modifications...

Integrated 3/2 Way Valves VOE Series OSPP25-C, 32-C, 40-C, and 50-C For optimal control of the OSP-P cylinder, 3/2 way valves integrated into the cylinder's end caps can be used as a compact and complete solution. They allow for easy positioning of the cylinder, smooth operation at the lowest speeds and fast response, making them ideally suited for the direct control of production and automation processes. • Complete compact solution • Various connection possibilities: Free choice of air connection with rotating end caps with VOE valves, • Air connection can be rotated 4 x 90°, • Solenoid...

Integrated exhaust throttle valve Possible positions of the exhaust throttle valve Dimension Table [mm] Series Possible positions of the exhaust throttle valve The right to introduce technical modifications is reserved Integrated exhaust throttle valve V17 Dimension Table [mm] Series Parker Hannifin Corporation Pneumatic Division - Europ

Order Instructions – Basic Cylinder 1-4 Stroke Length Version / Piston Classic Tandem L+R 270° = same side as outerband L 270° = same side as outerband R 0° = in front left standard right end face right standard left end face L 270° = same side as outerband R 0° = underneath Cover / Cable Channel Accessories - please order separately ! Description Mid-Section Support L 180° = at the back R 270° = same side as outerband Adaptor Profile T-Slot Profile Magnetic Switches Cable Channel Cable channel Cable channel two-sided without cover rail 270° same side as outerband 270° same side as...

Recirculating Ball Bearing Guide KF Versions for Pneumatic Linear Drive: Series OSPP-C KF ORIGA SYSTEM PLUS Loads, Forces and Moments Series KF16 to KF50 For Linear Drives Series OSPP-C CLASSIC Features: • Anodized aluminium guide carriage, the mounting dimensions correspond to FESTO Type: DGPL-KF • Polished and hardened steel guide rail • For high loads in all directions • High precision • Integrated wiper system • Integrated grease nipples • Any length of stroke up to 3700 mm • Maximum speed KF16. KF40: v = 3 m/s KF25. KF32, KF50: v = 5 m/s Technical Data The table shows the maximum...