PAN1762 Bluetooth Low Energy Module Design Guide Rev. 1.0 Wireless Modules

By purchase of any of the products described in this document the customer accepts the document's validity and declares their agreement and understanding of its contents and recommendations. Panasonic Industrial Devices Europe GmbH (Panasonic) reserves the right to make changes as required at any time without notification. Please consult the most recently issued Design Guide before initiating or completing a design. © Panasonic Industrial Devices Europe GmbH 2018. This specification sheet is copyrighted. Reproduction of this document is permissible only if reproduction is without alteration and...

Parasonic PAN1762 Bluetooth Module Design Guide Rev. 1.0 Page 3

Parasonic PAN1762 Bluetooth Module 1 About This Document This Design Guide applies to the Bluetooth development platform PAN1762 USB stick. The intention is to enable our customers to easily integrate our module PAN1762 in their product. This guide describes the hardware and gives useful hints. Design Guide Rev. 1.0 Page 4

PAN1762 Bluetooth Module 1 About This Document Related Documents [1] PAN1762 Software Guide Please refer to the Panasonic website for more information as well as related documents  5.2.2 Product Information.

PAN1762 Bluetooth Module 2 Overview 2 Overview The PAN1762 USB stick is a development platform for the PAN1762 Bluetooth low energy module to implement Bluetooth functionality into various electronic devices. This guide describes the hardware. Please refer to the Panasonic website for related documents  5.2.2 Product Information. Further information on the variants and versions  5.1 Ordering Information. FTDI UART

Parasonic PAN1762 Bluetooth Module Design Guide Rev. 1.0 Page 7

Parasonic PAN1762 Bluetooth Module Design Guide Rev. 1.0 Page 8

Parasonic PAN1762 Bluetooth Module Minimal configuration • VCC • GND • UART Rx, Tx, no flow control 2.3 UART Interface • Default baud rate: 115 200 • Data format: 8, Stop: 1, Parity: none, LSB first • Rx, Tx, no flow control Design Guide Rev. 1.0 Page 9

PAN1762 Bluetooth Module 3 Reference Design DHSDM DFSDM DHSDP DFSDP VBG PAN1762 USB-Stick Reference Design PLLFILT RBIAS USBDP USBDM SWDIO SWDCLK SLPXOIN RESET Jumper for Standalone mode or Host mode OSCI OSCO Jumper for both modes PAN1762 USB-Stick Reference Design USBDP_UP USBDM_UP Document Number: Date: 20.07.2018 10:35

PAN1762 Bluetooth Module 3 Reference Design Placement Recommendations Antenna Keep-Out Area Do not place any ground plane under the red marked restricted antenna area in any layer! This would be affecting the performance of the chip antenna in a critical manner. The following conditions must be met:  Keep this product away from heat. Heat is the major cause of decreasing the life of these products. Keep this product away from other high frequency circuits. To download the design files go to the download area on the product website  5.2.2 Product Information.

Parasonic PAN1762 Bluetooth Module .If possible place the module in the center of mother PCB. Keep-Out Area Use a ground plane in the area surrounding the module module wherever possible. Dimensions are in mm. Design Guide Rev. 1.0 Page 12

PAN1762 Bluetooth Module 3 Reference Design Building Blocks JTAG SWD for programming and debugging USB HUB IO breakout area IOs are switchable to GND or VDD to control e. g. host mode or standalone IOs can be connected to external e. g. sensor boards FTDI USB to UART conversion for host mode

PAN1762 Bluetooth Module 3 Reference Design Configuration Settings There are two different modes available. To use either host mode or standalone mode, GPIO1 and GPIO2 need to be configured as shown in the picture. After each different configuration the reset button needs to be pressed. The 3 V jumper can be removed for current measurements.

PAN1762 Bluetooth Module 4 Life Support Policy 4 Life Support Policy This Panasonic Industrial Devices Europe GmbH product is not designed for use in life support appliances, devices, or systems where malfunction can reasonably be expected to result in a significant personal injury to the user, or as a critical component in any life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. Panasonic customers using or selling these products for use in such applications do so...

Parasonic PAN1762 Bluetooth Module Design Guide Rev. 1.0 Page 16

PAN1762 Bluetooth Module 5 Appendix Contact Details Contact Us Please contact your local Panasonic Sales office for details on additional product options and services: For Panasonic Sales assistance in the EU, visit https://eu.industrial.panasonic.com/about-us/contact-us Email: [email protected] For Panasonic Sales assistance in North America, visit the Panasonic website “Sales & Support” to find assistance near you at https://na.industrial.panasonic.com/distributors Please visit the Panasonic Wireless Technical Forum to submit a question at https://forum.na.industrial.panasonic.com Product...