Group: Matsushita Electric Corporation
Catalog excerpts
2019 ProductsCatalog Hybrid Conductive Polymer Hybrid Aluminum Electrolytic Capacitors
Open the catalog to page 1Panasonic Notices / Items to be observed ■ Applicable laws and regulations •This product complies with the RoHS Directive (Restriction of the use of certain hazardous substances in electrical and electronic equipment (DIRECTIVE 2011/65/EU). • No Ozone Depleting Chemicals(ODC's), controlled under the Montreal Protocol Agreement, are used in producing this product. We do not use PBBs or PBDEs as brominated flame retardants. • Export procedure which followed export related regulations, such as foreign exchange and a foreign trade method, on the occasion of export of this product. • These...
Open the catalog to page 2Conductive Polymer Hybrid Aluminum Electrolytic Capacitors 1.1 Operating temperature and frequency Electrical characteristics of the capacitor are likely to change due to variation in temperature and/or frequency. Circuit designers should take these changes into consideration. (1) Effects ofoperating temperature on electrical parameters At higher temperatures : leakage current and capacitance increase while equivalent series resistance (ESR) decreases. At lower temperatures : leakage current and capacitance decrease while equivalent series resistance (ESR) increases. (2) Effects of...
Open the catalog to page 31.4 Using two or more capacitors in parallel The circuit resistance can closely approximate the series resistance of the capacitor, causing an imbalance of ripple current loads within the capacitors. Careful wiring methods can minimize the possible application of an excessive ripple current to a capacitor. Moreover, please do not use it in series. (1) Double-sided circuit boards Avoid wiring pattern runs, which pass between the mounted capacitor and the circuit board. (2) Clearance for case mounted pressure relief (S ^10 mm) Capacitors with case mounted pressure relief require sufficient...
Open the catalog to page 4(1) Observe temperature and time soldering specifications or do not exceed temperature of 350 °C for 3 seconds or less. (2) If a soldered capacitor must be removed and reinserted, avoid excessive stress on the capacitor leads. (3) Avoid physical contacts between the tip of the soldering iron and capacitors to prevent or capacitor failure. (1) Avoid moving the capacitor after soldering to prevent excessive stress on the lead wires where they enter the seal. The capacitor may break from element portion due to a torque at outer rim, causing a large stress to terminals. (2) Do not use the...
Open the catalog to page 53. Precautions for using capacitors 3.1 Environmental conditions Capacitors should not be stored or used in the following environments. (1) Exposure to temperatures above the upper category or below the lower category temperature of the capacitor. (2) Direct contact with water, salt water, or oil. (3) High humidity conditions where water could condense on the capacitor. (4) Exposure to toxic gases such as hydrogen sulfide, sulfuric acid, nitric acid, chlorine, chlorine compound, bromine, bromine compound or ammonia. (5) Exposure to ozone, radiation, or ultraviolet rays. (6) Vibration and...
Open the catalog to page 6Conductive Polymer Hybrid Aluminum Electrolytic Capacitors High voltage Long life -►
Open the catalog to page 7Panasonic Conductive Polymer Hybrid Aluminum Electrolytic Capacitors
Open the catalog to page 8Conductive Polymer Hybrid Aluminum Electrolytic Capacitors * Panasonic have several series available for pure Tin terminal ZVEI reflow based on J-STD-020D (JEDEC). Specifications for radial lead type • Flow soldering condition < RoHS compliant >
Open the catalog to page 9Conductive Polymer Hybrid Aluminum Electrolytic Capacitors Land / Pad pattern The circuit board land/pad pattern size for chip capacitors is specified in the following table. The land pitch influences installation strength and consider it. When size "A" is wide, back fillet can be made, decreasing fitting strength. *Take mounting conditions, solderability and fitting strength into consideration when selecting parts for your company's design.
Open the catalog to page 10Conductive Polymer Hybrid Aluminum Electrolytic Capacitors • Reel dimensions (not to scale) • Dimensions of outer carton box
Open the catalog to page 11Panasonic Conductive Polymer Hybrid Aluminum Electrolytic Capacitors Explanation of part numbers O Part number system • Surface mount type ZC 101 X Product classification 3 figures Voltage code 1 to 2 figures Capacitance Size code code 3 figures 0 to 1 figure Special code 0 to 1 figure Taping code 1 figure 1 • Radial lead type Product classification 4 figures Voltage code 2 figures Capacitance code 3 figures Series Code
Open the catalog to page 12Panasonic Conductive Polymer Hybrid Aluminum Electrolytic Capacitors Panasonic Conductive Polymer Hybrid Aluminum Electrolytic Capacitors Surface Mount Type ZA series V type High temperature lead-free reflowFeatures > Endurance : 10000 h at 105 °C > Low ESR and high ripple current (70 % over, Lower ESR than current V-FP) > High voltage (to 80 V.DC) > Equivalent to conductive polymer type aluminum electrolytic capacitor (There are little characteristics change by temperature and frequency) > Vibration-proof product is available upon request. New lineup of p6.3 product. (p6.3, p8, p10) >...
Open the catalog to page 13Panasonic Conductive Polymer Hybrid Aluminum Electrolytic Capacitors Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately.
Open the catalog to page 14Conductive Polymer Hybrid Aluminum Electrolytic Capacitors Surface Mount Type ZC series V type High temperature lead-free reflow Endurance: 4000 h at 125 ℃ (High temperature / Long life) Low ESR and high ripple current (85 % over, Lower ESR than current V-TP) High-withstand voltage ( to 80 V.DC), Low LC (0.01 CV or 3 μA) Equivalent to conductive polymer type aluminum electrolytic capacitor (There are little characteristics change by temperature and frequency) ● Vibration-proof product is available upon request. New lineup of φ6.3 product. (φ6.3, φ8, φ10) ● AEC-Q200 compliant ● RoHS...
Open the catalog to page 15All Panasonic Industrial catalogs and technical brochures
-
Conductive Polymer Capacitors
146 Pages
-
LAPRISS series
8 Pages
-
Gouging power source
1 Pages
-
350VR1 series
6 Pages
-
GZ4 series
2 Pages
-
LA-1800
2 Pages
-
Aluminum Electrolytic Capacitors
87 Pages
-
Device Product Catalog 2018
17 Pages
-
Film Capacitors
100 Pages
-
Automotive Devices Catalogue
10 Pages
-
Device Product Catalog 2017
17 Pages
-
Positioners & Peripherals
6 Pages
-
TA/TB Series
5 Pages
-
TA-WG Series
6 Pages
-
TSP
1 Pages
-
200BL2
1 Pages
-
TR6
1 Pages
-
TIG STAR WX4
1 Pages
-
300BZ3
1 Pages
-
300BP4
1 Pages
-
KR2series/600KH2
6 Pages
-
600RF2/FR1 series
6 Pages
-
500CL5/180SL7
6 Pages
-
400GT3
6 Pages
-
350GZ4/GR3series
6 Pages
-
350GE2
6 Pages
-
350GB2
6 Pages
Archived catalogs
-
MIG Welding Machines
4 Pages
-
CO2/MAG Welding Machines
4 Pages