*mydirectindustry

Catalogs
Panasonic Industrial, Robot & Welding
Aluminum Electrolytic Capacitors (Radial Lead Type)

Aluminum Electrolytic Capacitors (Radial Lead Type)

Product catalog summary

Overview: This document is a technical catalog for Panasonic's Aluminum Electrolytic Capacitors, specifically the radial lead type, as of May 2017. It includes specifications, application guidelines, and handling techniques for these capacitors.

Compliance and Regulations: The capacitors comply with the RoHS Directive and do not use ozone-depleting chemicals or certain brominated flame retardants. Export procedures must adhere to relevant regulations.

Applications and Limitations: These capacitors are intended for use in general electronic circuits such as audio/visual equipment and computers. They are not suitable for high-reliability applications where failure could harm human life or property without additional safety measures.

Design and Usage Guidelines:

Ensure compatibility with your product before use.
Do not exceed specified voltage, temperature, or ripple current limits.
Install failsafe systems in critical applications to prevent unsafe conditions.

Operating Conditions:

Temperature and frequency affect electrical characteristics; higher temperatures increase leakage current and capacitance.
Expected life doubles with each 10°C reduction in operating temperature.
Avoid reverse voltage, overvoltage, and excessive ripple current.

Installation and Handling:

Ensure correct polarity and spacing during installation.
Avoid excessive stress on leads and ensure proper soldering techniques.
Do not reuse capacitors from used equipment.

Cleaning and Maintenance:

Use suitable cleaning solvents and avoid halogenated solvents unless specified.
Thoroughly rinse and dry circuit boards after cleaning.

Cleaning and Solvent Guidelines: Avoid using certain solvents like 1,1,1-trichloroethane and acetone due to potential damage. Ensure thorough drying after cleaning to remove residual solvents.

Mounting Adhesives and Coating Agents: Avoid materials with halogenated solvents and chloroprene-based polymers. Ensure thorough drying to prevent residual solvents from being trapped.

Fumigation: Ensure no halogen remains after fumigation of wooden boxes to prevent electrical corrosion of capacitors.

Environmental Conditions: Capacitors should not be exposed to extreme temperatures, direct contact with water, high humidity, toxic gases, ozone, radiation, or excessive vibration and shock.

Electrical Precautions: Avoid touching capacitor terminals to prevent electric shock. Prevent short circuits with conductive materials.

Emergency Procedures: If pressure relief operates, turn off equipment and avoid contact with escaping electrolyte gas. Flush eyes with water if contact occurs.

Long Term Storage: Store capacitors at room temperature and humidity, avoiding direct sunlight. Expiration dates vary by series.

Capacitor Disposal: Dispose of capacitors by incineration after crushing or as solid waste, following local laws.

Capacitor Specifications: Various series of capacitors are listed with their temperature ratings and lifespan. Specifications include dimensions, voltage, capacitance, and endurance.

Diagrams and Dimensions: Detailed diagrams and dimensions for radial lead type capacitors are provided, including lead spacing and packaging specifications.

Specifications:

Category Temperature Range: -40°C to +105°C
Rated Voltage Range: 6.3 V.DC to 63 V.DC
Capacitance Range: 27 µF to 10000 µF
Capacitance Tolerance: ±20% (120 Hz/+20°C)
Leakage Current: I < 0.01 CV (µA) after 2 minutes
Dissipation Factor (tan δ): Varies with voltage, e.g., 0.22 for 6.3 V.DC

Endurance: Capacitors are tested with DC voltage and ripple current at +105°C±2°C. Duration varies by size, e.g., 5000 hours for 05×11/06.3×11.2, up to 10000 hours for larger sizes.

Shelf Life: After 1000 hours at +105°C±2°C without voltage, capacitors meet endurance limits after stabilization at +20°C.

Frequency Correction Factor for Ripple Current: Varies by capacitance and frequency, e.g., 0.45 at 60 Hz for 27 to 33 µF.

Additional Notes: Design and specifications are subject to change without notice. Contact the factory for current technical specifications before purchase or use. RoHS compliant and manufactured in Malaysia.

Procedures and Recommendations: The document advises users to request taped products by specifying the letter "B" or "H" for lead wire pitch. It also recommends referring to the "Taping dimensions" page for further details. Users are reminded to contact the manufacturer immediately if any safety concerns arise.

Norms and Standards: The capacitors are RoHS compliant, indicating adherence to environmental and safety standards. The document specifies the category temperature range from -25 °C to +105 °C and provides frequency correction factors for ripple current.

Key Features: The capacitors are designed for high ripple current at high frequencies, with endurance ranging from 8000 to 10000 hours. They include low-profile products with a height of 20 mm.

Data Summary: The document includes extensive tables listing part numbers, packaging quantities, and specific electrical characteristics for each capacitor type. It highlights the importance of ensuring that the sum of DC and ripple peak voltage does not exceed the rated working voltage during endurance testing.

Catalog excerpts

Aluminum Electrolytic Capacitors (Radial Lead Type)-1

2017 Products Catalog Aluminum Electrolytic Capacitors Radial lead type

Open the catalog to page 1

Aluminum Electrolytic Capacitors (Radial Lead Type)-2

——— Notices ——— ■ Applicable Laws and Regulations ● This product complies with the RoHS Directive (Restriction of the use of certain Hazardous substances in electrical and electronic equipment (DIRECTIVE 2011/65/EU). ● No Ozone Depleting Chemicals(ODC's), controlled under the Montreal Protocol Agreement, are used in producing this product. ● We do not use PBBs or PBDEs as brominated flame retardants. ● Export procedure which followed export related regulations, such as foreign exchange and a foreign trade method, on the occasion of export of this product. ■ Limited applications ● This capacitor...

Open the catalog to page 2

Aluminum Electrolytic Capacitors (Radial Lead Type)-3

Aluminum Electrolytic Capacitors (Radial Lead Type) Application Guidelines (Radial Lead Type) 1. Circuit design 1.1 Operating Temperature and Frequency Electrical characteristics of the capacitor are likely to change due to variation in temperature and/or frequency. Circuit designers should take these changes into consideration. (1) Effects of operating temperature on electrical parameters (a) At higher temperatures, leakage current and capacitance increase while equivalent series resistance (ESR) decreases. (b) At lower temperatures, leakage current and capacitance decrease while equivalent...

Open the catalog to page 3

Aluminum Electrolytic Capacitors (Radial Lead Type)-4

Aluminum Electrolytic Capacitors (Radial Lead Type) 1.4 Using Two or More Capacitors in Series or Parallel (1) Capacitors Connected in Parallel The circuit resistance can closely approximate the series resistance of the capacitor, causing an imbalance of ripple current loads within the capacitors. Careful wiring methods can minimize the possible application of an excessive ripple current to a capacitor. (2) Capacitors Connected in Series Differences in normal DC leakage current among capacitors can cause voltage imbalances. The use of voltage divider shunt resistors with consideration to leakage...

Open the catalog to page 4

Aluminum Electrolytic Capacitors (Radial Lead Type)-5

Aluminum Electrolytic Capacitors (Radial Lead Type) 2.2 Capacitor Insertion (1) (2) (3) (4) Verify the correct capacitance and rated voltage of the capacitor. Verify the correct polarity of the capacitor before insertion. Verify the correct hole spacing and land pattern size before insertion to avoid stress on the terminals. Ensure that the lead clinching operation done by auto insertion equipments does not stress the capacitor leads where they enter the seal of the capacitor. Do not immerse the capacitor body into the solder bath as excessive internal pressure could result. Apply proper soldering...

Open the catalog to page 5

Aluminum Electrolytic Capacitors (Radial Lead Type)-6

aluminum oxide film deteriorates as a to restore the oxide film. 2.9 Fumigation In exporting electronic appliances with aluminum electrolytic capacitors, in some cases fumigation treatment using such halogen compound as methyl bromide is conducted for wooden boxes. If such boxes are not dried well, the halogen left in the box is dispersed while transported and enters in the capacitors inside. This possibly causes electrical corrosion of the capacitors. Therefore, after performing fumigation and drying make sure that no halogen is left. Don’t perform fumigation treatment to the whole electronic...

Open the catalog to page 6

Aluminum Electrolytic Capacitors (Radial Lead Type)-7

■ Radial lead type Long Life • High ripple series KS/KA series Bi-polar 85 °C 1000 h ■ Surface mount type NE^|TCU series High temperature • Long life Htp series TK series TG series Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 02 j

Open the catalog to page 7

Aluminum Electrolytic Capacitors (Radial Lead Type)-8

Lead taping radial lead type • Dimensions Lead space (F) Case size (mm) 0DxL Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 06 Mar. 2016

Open the catalog to page 8

Aluminum Electrolytic Capacitors (Radial Lead Type)-9

Aluminum Electrolytic Capacitors (Radial Lead Type) (Lead space: 5 mm / 0D×L : 05×11, 06.3×11.2, 15) Sufﬁx code Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this

Open the catalog to page 9

Aluminum Electrolytic Capacitors (Radial Lead Type)-10

Aluminum Electrolytic Capacitors (Radial Lead Type) Figure H 1.3 > Packaging Specifications Dimensions of outer carton box b Packaging Quantity Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 0

Open the catalog to page 10

Aluminum Electrolytic Capacitors (Radial Lead Type)-11

Aluminum Electrolytic Capacitors (Radial Lead Type) Lead Forming Type (Snap-in) Lead formed Aluminium Electrolytic Capacitor for self mounting, for rationalization and upgrade of soldering process. 0D ✽ Direction of bending shape is not speciﬁed Series KA/KS Dimensions Unit : mm Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediat

Open the catalog to page 11

Aluminum Electrolytic Capacitors (Radial Lead Type)-12

Radial Lead Type Series : FC Type : A Features • Endurance : 105 °C 1000 h to 5000 h • Low impedance • RoHS compliant Specifications Category temperature range Rated voltage range Capacitance range Capacitance tolerance Leakage current I < 0.01 CV or 3 (jA) After 2 minutes (Whichever is greater) For capacitance value > 1000 jF add 0.02 per every 1000 jF Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 09...

Open the catalog to page 12

Aluminum Electrolytic Capacitors (Radial Lead Type)-13

Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 09 oct. 2016

Open the catalog to page 13

All Panasonic Industrial, Robot & Welding catalogs and technical brochures

Archived catalogs

*Prices are pre-tax. They exclude delivery charges and customs duties and do not include additional charges for installation or activation options. Prices are indicative only and may vary by country, with changes to the cost of raw materials and exchange rates.

Brand list