Catalogs >
Panasonic Electric Works Europe >
Addressable 2 voltage outputs unit 3364

Addressable 2 voltage outputs unit 3364
2Pages

Catalog excerpts

Addressable 2 voltage outputs unit 3364 - 1

Panasonic Electric Works Fire & Security Technology Europe AB Jungmansgatan 12, SE-211 19 Malmö, Sweden Tel: +46 (0)40 697 70 00 • Fax: +46 (0)40 697 70 99 info-fste@eu.pewg.panasonic.com • www.panasonic-fire-security.com Fire alarm systems Addressable 2 voltage outputs unit 3364 • Two programmable supervised voltage outputs • A special fire door closing voltage output General The Addressable 2 voltage outputs unit 3364 (AOU) is intended to be surface mounted. A plastic protection cover (with 10 cable inlets) is supplied. 3364 can be mounted in a waterproof box (3362). The unit is connected to a COM loop and require external 24 V DC power supply (3366). Inputs / Outputs / Connectors All connections are done on screw terminals. - COM loop (in) - COM loop (out) - 24 V DC power supply input - /Mains OK input (3366 output) - Two programmable and supervised 24 V DC outputs VO0 & VO1, intended for alarm devices. End-of-line capacitor to be mounted in the last device alt. capacitors in up to five devices. For each capacitor is also a series diode required, see the opposite side of this page. - One special 24 V DC output VO2, intended for fire door closing. VO2 is not only controlled by a control expression, it will also be powerless approx. 30 sec. after: - the /Mains OK input goes high (=3366 output /Mains OK goes high=no mains) - the COM loop communication is interrupted (=no comm. with the c.i.e.) Settings The COM loop address is set with an Address setting tool 3314. The unit has an address label where the address is to be written. 3314 is also used to set the mode: NORMAL mode: This mode can be used in system EBL512 with S/W version > 2.3 and in system EBL128. 2330 mode: This mode is used in system EBL512 with S/W version < 2.2.x and in system EBL1000. The unit shall be programmed in Win512 and PLAN1000 respectively as "SU4 Addressable 4 voltage outputs unit 2262 / 2263". The unit will in Win512 via "Check all loop units" be identified as an "SU4 Addressable 4 voltage outputs unit 2262 / 2263". (Two 3364 units connected to one power supply 3366 are intended to succeed the current 2262 unit with four voltage outputs.) 2312 mode: Not used for 3364. Waterproof box 3362 When required, the 3364 unit can be mounted in a waterproof box 3362 (IP 66/67). Product applications The 3364 unit is intended for indoor use and in dry premises (if not the waterproof box is used). It can be DIN rail mounted with help of a DIN rail interface kit 3363.

Open the catalog to page 1

Addressable 2 voltage outputs unit 3364 - 2

All technical features and data are subject to changes without notice, resulting from continuous development and improvement. Product Leaflet Date of issue Revision / Date of revision MEW00516 2006-10-13 5 / 2008-09-24 Type numbers 3364 Addressable 2 voltage outputs unit (incl. plastic protection cover and two 470nF capacitors). 3362 Waterproof box (IP 66/67) (incl. four compression glands). 3363 DIN rail interface kit for symmetric 35 mm DIN rail (plate, clamp & screws). 3366 External power supply. (230 V AC / 24 V DC, 2.2 alt. 0.85 A) Mounting holes c/c 60 mm D=3mm D1 D1 AD M C D2 VO0 &...

Open the catalog to page 2