Catalogs >
Panasonic Electric Works Corporation of America >
PAN1780‑AT

PAN1780‑AT
37Pages

Catalog excerpts

PAN1780‑AT Bluetooth® Low Energy Module with AT Command Set Wireless Connectivity

Overview The PAN1780‑AT is a Bluetooth 5 Low Energy (LE) module based on the Nordic nRF52840 single-chip controller with integrated BlueRadios nBlue™ Bluetooth AT.s LE Command Set. Bluetooth • LE 2 Mbps high speed PHY, LE long range Coded PHY Features • Surface mount type dimensions: LE advertising extensions (advertising on 40 channels total) Channel selection algorithm #2 LE secure connections Over-the-air update of AT Command Set Nordic nRF52840 featuring ARM Cortex -M4F with 64 MHz Bluetooth 5 LE including LE 2M and LE Coded PHY Embedded 1 MB flash memory and 256 kB internal RAM...

Open the catalog to page 2

PAN1780‑AT Bluetooth Module By purchase of any of the products described in this document the customer accepts the document's validity and declares their agreement and understanding of its contents and recommendations. Panasonic Industrial Devices Europe GmbH (Panasonic) reserves the right to make changes as required at any time without notification. Please consult the most recently issued Product Specification before initiating or completing a design. © Panasonic Industrial Devices Europe GmbH 2020. This specification sheet is copyrighted. Reproduction of this document is permissible only...

Open the catalog to page 3

PAN1780‑AT Bluetooth Module Disclaimer The customer acknowledges that samples may deviate from the Product Specification and may bear defects due to their status of development and the lack of qualification mentioned above. Panasonic rejects any liability or product warranty for Engineering Samples. In particular, Panasonic disclaims liability for damages caused by:  The use of the Engineering Sample other than for evaluation purposes, particularly the installation or integration in another product to be sold by the customer, Deviation or lapse in function of the Engineering Sample,...

Open the catalog to page 4

1 About This Document 1 About This Document 1.1 Purpose and Audience This Product Specification provides details on the functional, operational, and electrical characteristics of the Panasonic PAN1780‑AT module. It is intended for hardware design, application, and Original Equipment Manufacturers (OEM) engineers. The product is referred to as “the PAN1780‑AT” or “the module” within this document. Revision History Revision First version Description Note Indicates important information for the proper use of the product. Non-observance can lead to errors. Attention Indicates important notes...

Open the catalog to page 6

2 Overview The PAN1780‑AT is a Bluetooth 5 Low Energy module based on the Nordic nRF52840 single-chip controller with integrated BlueRadios nBlue Bluetooth AT.s LE Command Set. Bluetooth 5 features additionally a higher symbol rate of 2 Mbps using the high-speed LE 2M PHY or a significantly longer range using the LE Coded PHY at 500 kb/s or 125 kb/s. The new channel selection algorithm (CSA#2) improves the performance in high interference environments. Furthermore, the new LE advertising extensions allow for much larger amounts of data to be broadcasted in connectionless scenarios. An...

Open the catalog to page 7

Block Diagram

Open the catalog to page 8

Digital BI/Analog Input Digital BI/Analog Input Digital BI/Analog Input Digital BI/Analog Input PIOs 2, 5, 7, 8, 16 (RTS) and 17 (Tx) default to outputs. PIOs 3, 4, 6, 14, 15 (CTS) and 18 (Rx) default to inputs with 3, 4, 6 and 14 pulled low. All other inputs default to the disconnected state. Pin functions, directions and pull characteristics may be changed via AT commands.

Open the catalog to page 9

 PAN1780‑AT Bluetooth Module No. Pin Name Leave open Digital BI/Analog Input Digital BI/Analog Input Digital BI/Analog Input Leave open GPIO or Trace IF Clock BRSP TOGGLE UART_RX and UART_CTS are digital inputs and need to be kept from floating. Therefore UART_RX should be pulled high and UART_CTS should be pulled low if not connected to another UART.

Open the catalog to page 10

 PAN1780‑AT Bluetooth Module No. Pin Name Supply Voltage Digital BI/Analog Input Serial Wire Debug IF Clock Normally leave unconnected FACTORY, RESET, RECONNECT, DISCONNECT SLEEP TOGGLE GPIO GPIO GPIO Supply Voltage Supply Voltage Reset Signal Low Active

Open the catalog to page 11

 PAN1780‑AT Bluetooth Module No. Pin Name Serial Wire Debug IF Data Full-speed USB 2.0 device controller UART (2 or 4 wire with CTS/RTS, 9 600 up to 921 600 baud) 8 channel 12 bit ADC Temperature sensor 46 PIOs Integrated 32 kHz crystal Bluetooth Features • • Bluetooth LE 5 Supports Bluetooth LE 5 high speed and long range modes

Open the catalog to page 12

Dimensions All dimensions are in millimeters.

Open the catalog to page 13

Footprint All dimensions are in millimeters. The outer dimensions have a tolerance of 0.3 mm.

Open the catalog to page 14

Packaging The module is a mass production status product and will be delivered in the package described below. Tape Dimensions Direction of unreeling (for customer) trailer (empty) 1 x circumference / hub (min 160mm) component packed area standard 1500pcs leader (empty) minimum 10 pitch Top cover tape more than 1 x circumference plus 100mm to avoid fixing of tape end on sealed modules. Empty spaces in the component packed area shall be less than two per reel and those spaces shall not be consecutive. The top cover tape shall not be found on reel holes and it shall not stick out from the reel.

Open the catalog to page 15

Component Direction Pin 1 Marking (Top Side) Direction of unreeling (for customer) Reel Dimension

Open the catalog to page 16

Package Label Example: Customer order number, if applicable Order number Date code Hardware/software version Total Package

Open the catalog to page 17

Case Marking Example: 1 Brand name 2 Hardware/software version 3 Order number 4 Lot code 5 Status: ES or empty for MP 6 2D barcode, for internal usage only 7 Marking for Pin 1 8 Bluetooth logo

Open the catalog to page 18

4 Specification All specifications are over temperature and process, unless indicated otherwise. Default Test Conditions Temperature: Humidity: Supply Voltage: Absolute Maximum Ratings The maximum ratings may not be exceeded under any circumstances, not even momentarily or individually, as permanent damage to the module may result. Normal Supply Voltage High Supply Voltage Storage Temperature Moisture Sensitivity Level

Open the catalog to page 19

PAN1780‑AT 37Pages

Catalog excerpts

All Panasonic Electric Works Corporation of America catalogs and technical brochures

PAN1780‑AT
37Pages