4.80 H
46Pages

4.80 H Automotive-Lift date 12/2002 Manual date: 17.12.2002 Retailer address / phone Nußbaum Hebetechnik GmbH & Co.KG//Korker Straße 24//D-77694 Kehl-Bodersweier//Tel: +49(0)7853/8990 Fax: +49(0)7853/8787//E-mail: info@nussbaum-lifts.de//http://www.nussbaum-lifts.de

Operating Instruction and Documentation 4.80 H

Operating Instruction and Documentation 4.80 H Foreword Nußbaum lifting systems are the result of over 25 years experience in the automotive lifting industry. The high quality and the superior concept ensure reliability, a long lift lifetime and above all and economic business solution. To avoid unnecessary damage, injury or even death, read the operating instructions with care and observe the contents. Nußbaum lifts is not responsible for incidents involving the use of Nußbaum lifting systems for applications other than those for which they were designed. Nußbaum Hebetechnik GmbH & Co. KG...

Operating Instruction and Documentation 4.80 H The lift must only be operated : For its appropriate use In faultless condition concerning technical security. Organisational Requirements The instructions for use are to be kept at the place of operation being easily accessible at any time. In addition to the instructions for use, rules pertaining to other regulations i.e. accident prevention and environmental rules are to be observed and adhered to. The owner of the Nußbaum lifting system must ensure that operators and persons working with or around the lift occasionally conduct “refresher”...

Operating Instruction and Documentation 4.80 H After completely filling out this sheet including signatures, copy and return the original to the manufacturer. The copy must remain in the manual.. The initial safety check was carried out and the lift was started. The installation was carried out by the operating authority/competent (please delete as applicable). The initial safety check was carried out by a competent person before the initial operation. The operating authority confirms the correct installation of the automotive lift, the competent person confirms the correct initial...

Operating Instruction and Documentation 4.80 H the safety was checked and the lift was started. The persons below were introduced after the installation of the automotive lift. The introduction was carried out by either the erector from the lift-manufacturer or from a franchised dealer (competent person).

Operating Instruction and Documentation 4.80 H 1.General Information The document “Operating Instructions and Documentation” contains important information about installation, operation and maintenance of the automotive lift. • Conformation of installation of the automotive lift is recorded on the ”Record of Installation” form and must be signed and returned to the manufacturer. • Conformation of once of, regular and out of the ordinary service checks is recorded in the respective check forms. The forms are used to document the checks. They should not be removed from the manual. All Changes...

Operating Instruction and Documentation 4.80 H 2.Master document of the automotive lift 2.1 Lift–manufacturer Otto Nußbaum Hebetechnik GmbH & Co. KG Korker Straße 24 D-77694 Kehl-Bodersweier 2.2 Application The automotive lift 4.80 H is a lifting mechanism for lifting motor vehicles with a laden weight of up to 8000 kg . The max. load distribution is 2:1 either in or against the drive-on direction. The automotive lift has been designed for servicing vehicles only. It has not been designed to carry people. Carrying people either directly on the lift or in vehicles that are on the lift is...

Operating Instruction and Documentation 4.80 H

Operating Instruction and Documentation 4.80 H 3. Technical Information 3.1 Technical ratings Capacity : Load distribution max. 2:1 in or against the drive on direction Lifting time: Lowering time Lifting height: approx. 45 sec. with load approx. 12 sec. with load max. 1800 mm Line voltage Power rating Motor speed: Pump capacity Hydraulic pressure Pressure control valve 3 kW (Nr. 990303) 2800 rotation/min 4,3 cm3/rotation approx. 240 bar approx. 260 bar Sound level 3~/N+PE, 400V, 50 Hz fuse T16A (time-lag fuse) observe your state regulations 3.2 Safety device 1. Safety ratchet Safety device...

Operating Instruction and Documentation 4.80 H

Operating Instruction and Documentation 4.80 H 3.4 Foundation diagram drawing

Operating Instruction and Documentation 4.80 H

Operating Instruction and Documentation 4.80 H 4.Safety regulations When using automotive lifts the safety regulation EN1493/Aug.98 (CEN/TC98 „ Automotive lifts”) must be observe adhered to. Especially the following regulations are very important: • The laden weight of the lifted vehicle must not exceed 8000 kg for the automotive lift. Load distribution max. 2:1 in or against the drive on direction. • The automotive lift must be in its lowest position (fully collapsed), before the vehicle can be driving on to the lift. Only then can the vehicle be lifted. • While working with the lift the...

Operating Instruction and Documentation 4.80 H • Check all the danger points of the lift and ensure that there are no objects or people in the working area around the lift or on the lift. • Switch on the main switch. • Raise the vehicle Press the button „Lifting“. • Raise the vehicle to the required working height. Press the button “lifting“ . • Observe the complete process. 5.2 Lowering the vehicle • Check all danger points of the lift and be sure that there are no objects or people in the working area (danger area) around the lift or on the lift.. • Press the button at the lever....

Operating Instruction and Documentation 4.80 H 5.3 Lower the lift into the safety ratchets • Press the button „lowering“ and the pull the lever slowly. The lowering process begins directly. • Press the button „lifting“ to raise the lift out of the ratchets. 5.4 Adjusting the platform • It is possible to adjust the rail of the different wheelbase. That is necessary to reach the different wheelbases of the vehicles. One platform is only movable without load. The measure 850-1150 mm between the platform can reached. • Remove the load and raise the lift on approx.1000 mm height. The platform is...