ADO MICRO
16Pages

Small diameter carbide drills with oil holes

Excellent surface smoothness 4 Large size range

Oil Hole Large flow volume enables superior chip evacuation Double Margin Supports straightness of drill direction IchAda Coating Provides excellent surface smoothness Extended Flute Removed End of Margin Cutting Data Drilling | Solid carbide Greater coolant flow volume achieved by the hollow shank design to enable smooth chip evacuation Tool

Drilling | Solid carbide | 2xD ■ First choice in quality and performance ■ 2 flute carbide drill with internal coolant, IchAda coating ■ Up to 2xD ■ 17 sizes

Drilling | Solid carbide | 5xD ■ First choice in quality and performance ■ 2 flute carbide drill with internal coolant, IchAda coating ■ Up to 5xD ■ 17 sizes

Drilling | Solid carbide | 12xD X thinning ■ First choice in quality and performance ■ 2 flute carbide drill with internal coolant, IchAda coating ■ Up to 12xD, long type ■ 11 sizes

ADO-MICRO 20D NEW Drilling | Solid carbide | 20xD First choice in quality and performance 2 flute carbide drill with internal coolant, IchAda coating Up to 20xD, long type 11 sizes

Drilling | Solid carbide |30xD ■ First choice in quality and performance ■ 2 flute carbide drill with internal coolant, IchAda coating ■ Up to 30xD, long type ■ 11 sizes

CUTTING DATA Stable Performance Stable performance even in deep-hole applications The double margin enhances the straightness stability of drill to enable stable drilling performance > Also reduces the rifle marks on the inner surface of hole ADO-MICRO (Double Margin) Conventional (Single Margin) Work Material: SUS304 Depth of Hole: 40mm High Efficiency Approximately 9 times the drilling efficiency by non-step drilling Non-step drilling is possible even for deep holes, enabling high efficiency processing Drilling Time (sec/hole) Non-step drilling Step drilling (0,5mm step) Cutting Speed...

CUTTING DATA Long tool life achieved by stable drilling Benefit of unique flute geometry Number of holes Tool Work Material Cutting Speed 38mm (Blind) with pilot hole Corner shipping Extensive chipping on thinning Water-Soluble (Internal) Coolant Pressure Large coolant flow volume to enable stable drilling Benefit of enlarged oil holes Number of holes Cutting Speed Water-Soluble (Internal) Coolant Pressure Vertical machining center (HSK-A63) Cutting Data Work Material Breakage, twined chips 131 Holes Vertical machining center (HSK-A40) Drilling | Solid carbide Still Running Chisel is worn...

Cutting edge condition in special steel drilling application Tool Cutting edge wear condition after drilling 900 holes Cutting Data Drilling | Solid carbide

CUTTING CONDITIONS Drilling | Solid | Cutting conditions This cutting condition chart is based on the usage of water-soluble coolant and internal oil supply. Please use quality water-soluble coolant with a dilution factor of approximately 20 times. Please use a precision filter (approximation of 3pm to 5pm) to prevent the oil holes from clogging. Although the recommended coolant pressure is 3 MPa or more, please adjust accordingly if the level of flow volume is unsatisfactory due to the type and concentration of cutting oil used. For accurate mounting, acceptable deflection of the body...

ADO-MICRO 12D/20D/30D Recommended drilling method for deep-holes ①ADO-MICRO 2D Make a pilot hole with the ADO-MICRO 2D. ②Insert the long drill into a pilot hole with a low revolution of 500 to 1,000 min-1 (n). ADO-MICRO 2D (140°) The ADO-MICRO 2D (140° point angle) is the recommended pilot hole drills of the ADO-MICRO 12D/20D/30D. ADO-MICRO 12D20D30D DC DC[+0.010] ③ Increase the revolution to the designated speed and start drilling. ★ When work ing on a cur ved sur f ace, use the FX-ZDS (end mill for counterboring) or the ADF (carbide flat drill) to counterbore a flat surface before...

Branch office of OSG SCANDINAVIA Abrahams Grand 8 295 35 Bromolla Sweden Tel: +46 40 41 22 55 osg@osg-scandinavia.com OSG SCANDINAVIA (For Scandinavian countries) Langebjergvaenget 16 4000 Roskilde Denmark Tel: +45 4 6 75 65 55 osg@osg-scandinavia.com OSG NETHERLANDS Bedrijfsweg 5 3481 MG Harmelen The Netherlands Tel: +31 348 44 2764 Fax: +31 348 44 2144 info@osg-nl.com Shelton house, 5 Bentalls Pipps Hill Ind Est, Basildon Essex SS14 3BY United Kingdom Tel: +44 1268 567660 Fax: +44 1268 567661 sales@osg-uk.com .© OSG IBERICA Bekolarra 4 E - 01010 Vitoria-Gasteiz Spain Via Cirenaica n. 52...

CZECH REPUBLIC, SLOVAKIA, HUNGARY OSG Europe Logistics S.A. Slovakia, organizačná zložka Račianska 22/A, Bratislava 831 02 Slovakia Tel.: +421 24 32 91 295 info@osgeurope.com OSG RUSSIA Butlerova street, 17B, office 5069 117342 Moscow Russia Tel: +7 (495) 150 41 54 info@osg-russia.com ROMSAN INTERNATIONAL CO. SRL Reprezentant Exclusiv OSG 25C, Bucuresti-Magurele Street 051431 Bucuresti România Tel: +40 21 322 07 47 Fax: +40 21 321 56 00 romsan.int@romsan.ro Vischer & Bolli AG Machining and Workholding Im Schossacher 17 CH-8600 Dübendorf Schweiz Tel.: +41 44 802 15 15 Fax: +41 44 802 15 95...

OSG EUROPE LOGISTICS Avenue Lavoisier 1 B-1300 Z.I. Wavre - Nord - Belgium Tel: +32 10 23 05 07 Fax: +32 10 23 05 51 info@osgeurope.com OSG POLAND Sp. z.o.o. Spotdzielcza 57 05-074 Halinow - Poland Tel: +22 760 82 71 Fax: +22 760 82 71 osg@osg-poland.com OSG FRANCE Parc Icade, Paris Nord 2 Immeuble "Le Rimbaud" 22 Avenue des Nations CS66191 - 93420 Villepinte - France Tel: +33 1 49 90 10 10 Fax: +33 1 49 90 10 15 sales@osg-france.com ROMSAN INTERNATIONAL CO. SRL Reprezentant Exclusiv OSG 25C, Bucuresti-Magurele Street 051431 Bucuresti - Romania Tel: +40 21 322 07 47 Fax: +40 21 321 56 00...