Catalog excerpts
Carbide flat drill
Open the catalog to page 11 Designed for a wide variety of applications Exceptional wear resistance & toughness 3 Unique end cut geometry : Stable cutting resistance
Open the catalog to page 2Wide chip pocket Balanced point form Improved cutting edge Designed for a Wide Variety of Application Applicable for a multitude of drilling applications such as inclined surface, curved surface, flat-bottom hole, eccentric hole, and more. Standard lineup for thread forming of pilot holes under M6. Burrless Inclined Surface Guide Hole Thin Plate Blind Hole for Threading Through-Hole in Curved Surface Correction of Eccentric Hole Counterboring in Intricate Position Counterboring in Curved Surface Curved Exit Surface
Open the catalog to page 3Key features & Benefits of ADF 2 New Coating Exceptional Wear Resistance & Toughness Suppresses friction with the wear resistance layer; prevents breakage with the nano periodical layer Machined Surface Coating Structure Wear-Resistant Layer View from top Cutting Speed Nano Periodical layer After Drilling 1.620 holes Still Good After Drilling 660 holes Chipping半割加工 00000000000 Horizontal Machining Center Water Soluble Stable Cutting Resistance 上から見た図 View from top Unique end cut geometry reduces cuttingバリレス to force enable stable machining. 000000 Cutting Resistance Waveform 00000000000...
Open the catalog to page 4Machining Data Pilot Hole 入り組んだ位置の座ぐり加工shift in hole position 2mm 半割加工 穴座ぐり加工 Amount of Amount of shift in hole position 0 mm 00000000000 Pilot Hole Work Material Flat Surface Pilot Hole Machined Surface Cutting Speed ■ Shift length in hole position [mm] 133 mm/min (0,1 mm/rev) 34 mm (Blind) Water Soluble Horizontal Machining Center Pilot Hole Conventional Carbide Drill 上から見た図 View from top Feed Rate Amount of shift in hole position 0 mm Amount of shift in hole position 2 mm ■ Through-Hole in Curved Surface Tool Machine
Open the catalog to page 5Machining Data ■ Half-Hole View from top Machined Surface Flat Surface Work Material Cutting Speed Feed Rate Water Soluble Conventional Carbide Drill Fallen amount Competitor 上から見た図 Horizontal Machining Center ■ Flat Surface View from top 出口曲面加工 Oversize Tool Machined Surface Work Material Cutting Speed Feed Rate Flat Surface
Open the catalog to page 6Machining Data Tool Machined Surface Cutting Speed Feed Rate Shift length in hole position Water Soluble Horizontal Machining Center ■ Guide for Icons ■ Tool Materials Corner Chipping 1,7 times Corner Chipping Angled Surface Work Material Corner Chipping Corner Chipping Micro Grain Carbide EgiAs Coating ■ Tolerance drill diameter
Open the catalog to page 7Drills may have some discoloration, but it does not cause any performance problems. Applications - Anwendungen - Applicazioni - Applications - Applikation - Applikation - Aplicaciones - Применение - Uygulama - Zastosowania C≤0.2%
Open the catalog to page 8Drills may have some discoloration, out it does not cause any performance problems.
Open the catalog to page 9Conditions ADF-2D Low Carbon Steel - Alloy Steel Carbon Steel Work Material Plastic Mold Steel Cutting Speed Alloy Steel Feed Rate (mm/rev) Feed Rate (mm/rev) Feed Rate (mm/rev) Special Alloy Steel-Hardened Steel-Prehardened Steel Feed Rate (mm/rev) Feed Rate (mm/rev) Ductile Cast Iron Aluminum Alloy Feed Rate (mm/rev) Feed Rate (mm/rev) Feed Rate (mm/rev) Feed Rate (mm/rev) 1. Water-soluble coolant may be applied as noted in the above table only under the premise that the work surface has been flattened by milling. 2. When using non-water soluble oil or water-emulsifiable (over 20 times...
Open the catalog to page 10Conditions ADFLS-2D Low Carbon Steel - Alloy Steel Carbon Steel Work Material Feed Rate (mm/rev) Feed Rate (mm/rev) Special Alloy Steel-Hardened Steel-Prehardened Steel Plastic Mold Steel Cutting Speed Alloy Steel Feed Rate (mm/rev) Feed Rate (mm/rev) Feed Rate (mm/rev) Ductile Cast Iron Aluminum Alloy Feed Rate (mm/rev) Feed Rate (mm/rev) Feed Rate (mm/rev) 1. To process flat surfaces, prior center-drilling with a larger diameter is required. 2. Water-soluble coolant may be applied as noted in the above table only under the premise that the work surface has been flattened by milling. 3....
Open the catalog to page 11OSG EUROPE LOGISTICS Avenue Lavoisier 1 B-1300 Z.I. Wavre - Nord Belgium Tel.: +32 10 23 05 07 Fax: +32 10 23 05 11 info@osgeurope.com SLOVAKIA Branch office of OSG Europe Logistics s.a. Tel: +32 10 23 05 04 Fax: +32 10 23 05 31 info@osg-belgium.com http://ee.osgeurope.com OSG POLAND 59 Złota St 00-120 Warsaw Poland OSG FRANCE Parc Icade, Paris Nord 2 Immeuble “Le Rimbaud” 22 Avenue des Nations CS66191 - 93420 Villepinte France Tel.: +33 1 49 90 10 10 Fax: +33 1 49 90 10 15 sales@osg-france.com OSG NETHERLANDS Bedrijfsweg 5 - 3481 MG Harmelen Postbus 50 - 3480 DB Harmelen The Netherlands...
Open the catalog to page 12All OSG catalogs and technical brochures
-
ADO-MICRO
16 Pages
-
V-XPM-HT
4 Pages
-
V-XPM-HT
4 Pages
-
S-XPF VOL.8.1
52 Pages
-
S-TAP SERIES
40 Pages
-
ADO-SUS SERIES VOLUME 4.2
20 Pages
-
SOMTA VOL-5.1
64 Pages
-
ADO MICRO
16 Pages
-
ADO 40D 50D
12 Pages
-
CATALOGUE VI
1024 Pages
-
EPL-HP Series
8 Pages
-
Thread Mill Series
24 Pages
-
XPF Series
32 Pages
-
A-TAP Series
52 Pages
-
PSTW Phoenix
8 Pages
-
AE-VMS
8 Pages
-
EX-(SUS)-Series
24 Pages
-
DCT Diameter Correction Tool
8 Pages
-
HY-PRO Milling Series Vol.3
12 Pages
-
HY-PRO Drill Series Vol.3
20 Pages
-
TDXL HSS Drill Series
12 Pages
-
H-TAP H-SFT/H-POT
12 Pages
-
WDO Drill Series
12 Pages
-
Long-neck & Bull nose end mills
28 Pages
-
VP(O)-DC-MT Tap Series
8 Pages
-
OSG Indexable Series
111 Pages
-
OSG HSS End Mills Catalog
38 Pages
-
OSG Milling Catalog
234 Pages
-
OSG Drills Catalog
148 Pages
-
OSG Taps Catalog
285 Pages
-
Dental Solutions Vol.5
24 Pages
-
Composite Solutions Vol.3
28 Pages