video corpo

NX series - 44 Pages

Add to MyDirectIndustry favorites
NX series

Catalog excerpts

Tuning-Free AC Servo Motor Unit NX Series An AC servo motor unit that is capable of high accuracy control with easy operation. Smooth operation can be achieved in high inertia loads or belt drive applications without manual tuning.

 Open the catalog to page 1

Tuning-Free AC Servo Motor Unit NX Series Standard Type ■Features ●Easy Operation ●Easy Handling As with a stepping motor, stable operation can be achieved in high inertia drive and belt mechanism drive applications without gain adjustment. Also, adjusting the gain manually enables operation under even more stringent load conditions. Basic settings and adjustments are made with switches and potentiometers on the front panel. This design allows for easy control without a computer and even saves the hassle of complicated UP and DOWN key operations. ◇ Achieves High Inertia Drive With automatic...

 Open the catalog to page 2

This servo unit can operate in 4 control modes. Also, with the separately sold control module (OPX-2A) or data setting software (MEXE02), the functions of each control mode can be extended. Variation of the generated torque relative to the set torque (torque accuracy) has been improved, resulting in highly accurate torque control. ◇ Position Control The built-in high-resolution 20-bit absolute encoder enables highly accurate positioning. ●High Speed and High Response High-speed positioning can be performed utilizing the high-speed and high-response characteristics. 5500 r/min Factory...

 Open the catalog to page 3

●High Performance Geared Motors ◇ High Permissible Torque and Wide Permissible Speed Range Geared motors with high permissible torque that fully utilize the motor output torque. NX65AA-PS25-◇ There are screw holes that permit installation of a load directly on the rotating surface integrated with the shaft. Since the load can be installed here directly (surface installation), the design is simple when using an index table. 10 Maximum Torque Torque [N·m] Geared motors that use high accuracy gears with an angular transmission accuracy of 4 arc minutes and backlash of 3 arc minutes. ◇ Surface...

 Open the catalog to page 4

■System Configuration ●Standard Type with Electromagnetic Brake An example of a single axis system configuration with the SG8030J controller in position control mode is shown below. ✽Not supplied Accessories (Sold separately) ① Connection Cable Sets Flexible Connection Cable Sets ( ➜ Page 37) ② Extension Cable Sets Flexible Extension Cable Sets ( ➜ Page 37) ④ Data Setting Software ( ➜ Page 41) ③ Control Module ( ➜ Page 41) For Electromagnetic Brake 24 VDC Power Supply✽ Driver Computer✽ Controller (Sold separately) Programmable Controller✽ The product comes with 1 m, 2 m or 3 m cables (for...

 Open the catalog to page 5

■Product Number Code 4: 42 mm 6: 60 mm (60 mm) 8: (80 mm) 9: 85 mm (90 mm) 10: (104 mm) ( ) indicates the frame size for the gearhead ③ Output Power ④ Configuration 5: 50 W 10: 100 W 20: 200 W 40: 400 W 75: 750 W A: Standard M: Electromagnetic Brake Type Motor Frame Size Power-Supply Input A: Single-Phase 100−115 VAC C: Single-Phase/Three-Phase 200−230 VAC S: Three-Phase 200−230 VAC Gear Type PS: PS Geared Type J: PJ Geared Type Blank: Standard Type ⑦ Gear Ratio ⑧ Cable Length (Included) ■Product Line ●Standard Type Power-Supply Input Single-Phase 100-115 VAC ●Standard Type with...

 Open the catalog to page 6

Standard Type Standard Electromagnetic Brake Type W r/min r/min N·m N·m Product Name Rated Output Power Rated Speed Maximum Speed Rated Torque Maximum Instantaneous Torque Rotor Inertia Permissible Load Inertia✽2 Resolution Absolute Encoder 1 rotation 20 bits, multiple rotations 16 bits Single-Phase 100-115 VAC −15% to +10% 50/60 Hz Single-Phase 200-230 VAC −15% to +10% 50/60 Hz Three-Phase 200-230 VAC −15% to +10% 50/60 Hz AC Main Power Supply Voltage and Frequency Power-Supply Input DC Control Power Supply Single-Phase 100-115 VAC Single-Phase 200-230 VAC Three-Phase 200-230 VAC Type...

 Open the catalog to page 7

The brackets [ ] indicate the value for the electromagnetic brake type. The gearhead internal inertia is the motor shaft converted value. The value for 50 times the rotor inertia. The resolution for the motor output shaft. These values are for operation in the continuous duty region. For operation in the limited duty region, the maximum current is approximately 3 times the value shown. The electromagnetic brake is for holding the position when the power supply is OFF. The electromagnetic brake cannot be used to stop the motor. A separate power supply for the electromagnetic brake is also...

 Open the catalog to page 8

The brackets [ ] indicate the specifications for the electromagnetic brake type. The gearhead internal inertia is the motor shaft converted value. The value for 50 times the rotor inertia. The resolution for the motor output shaft. These values are for operation in the continuous duty region. For operation in the limited duty region, the maximum current is approximately 3 times the value shown. The electromagnetic brake is for holding the position when the power supply is OFF. The electromagnetic brake cannot be used to stop the motor. A separate power supply for the electromagnetic brake...

 Open the catalog to page 9

The brackets [ ] indicate the value for the electromagnetic brake type. The gearhead internal inertia is the motor shaft converted value. The value for 50 times the rotor inertia. The resolution for the motor output shaft. These values are for operation in the continuous duty region. For operation in the limited duty region, the maximum current is approximately 3 times the value shown. The electromagnetic brake is for holding the position when the power supply is OFF. The electromagnetic brake cannot be used to stop the motor. A separate power supply for the electromagnetic brake is also...

 Open the catalog to page 10

Product Name Rated Output Power Motor Permissible Speed Permissible Torque Maximum Torque Permissible Speed Range Rotor Inertia Gearhead Internal Inertia ✽2 Permissible Load Inertia✽3 Gear Ratio Resolution ✽4 Detector Backlash Power-Supply Input Voltage and Frequency Rated Input Current ✽5 A Three-Phase 200-230 VAC Type Power-Supply Input Power Consumption Excitation Current Static Friction Torque arc minutes (degrees) AC Main Power Supply DC Control Power Supply The brackets [ ] indicate the specifications for the electromagnetic brake type. The gearhead internal inertia is the motor shaft...

 Open the catalog to page 11

All ORIENTAL MOTOR catalogs and technical brochures

  1. RKII - Series

    68 Pages

  2. AR AC - Series

    50 Pages

  3. AZ DC - Series

    28 Pages

  4. AZ AC - Series

    28 Pages

  5. BX2 - Series

    27 Pages

  6. EMU series

    4 Pages

  7. BLE2 Series

    20 Pages

  8. KII/KIIS

    60 Pages

  9. EZS Series

    44 Pages

  10. SPV - Series

    7 Pages

  11. EZA - Series

    2 Pages

  12. TM - Series

    32 Pages

  13. ES - Series

    16 Pages

  14. FPW - Series

    22 Pages

  15. V - Series

    7 Pages

  16. CMK Series

    25 Pages

  17. RK? Series

    68 Pages

  18. AR Series

    6 Pages

  19. BLV Series

    16 Pages

  20. BLH Series

    18 Pages

  21. BMU Series

    28 Pages

  22. BLF Series

    20 Pages

  23. BLE Series

    32 Pages

  24. BLA Series

    2 Pages

  25. BXII Series

    36 Pages

  26. US Series

    26 Pages

  27. ES series

    16 Pages

  28. ES02

    22 Pages

  29. Torque Motors

    13 Pages

  30. BH Series

    8 Pages

  31. BHF Series

    13 Pages

  32. AR Series - DC

    48 Pages

  33. AR Series - AC

    50 Pages

  34. PK Series

    59 Pages

  35. Product range

    11 Pages