Catalogs >
ORIENTAL MOTOR >
K S Series

K S Series
14Pages

Catalog excerpts

Standard AC Motor Three-Phase High-Efﬁciency Induction Motor Terminal Box Type Right-Angle Hypoid Gear JH Gearhead Stainless Steel Shaft / IP66 30 W (1/25 HP) / 40 W (1/19 HP) / 100 W (1/8 HP) High Efficiency Three-Phase Motors through Optimal Design ●High Efficiency at a Maximum of 74% ●High Performance Specialized components and an optimal magnetic design are used to make high efficiency three-phase motors with a maximum efficiency of 74%. Motors are fanless with increased motor torque. Characteristics have been improved through pursuit of the specifications required for the three-phase motor and a review of the design to create a high-performance motor with little speed reduction even with a large load. ● Changes in Speed according to Load Optimized Configuration of Steel Plate Specialized Three-Phase Motor Design Low Loss Magnetic Steel Sheet Load Torque[N·m] K S Series Conventional Product Rated Torque Increased Winding Space Factor ● Comparison of Max. Efficiency (Reference values) K S Series Conventional Product ●Power Consumption Reduced by up to 10% Compared to a conventional 90 W (1/8 HP) motor under the same conditions, power consumption is reduced by a maximum of about 10%, contributing to the equipment's energy savings. Conventional Product ●Fanless With reduced loss, there is less heat generation in the motor, so the cooling fan that was incorporated into the conventional 60 W (1/12 HP) min. products is no longer included. K S Series Output power of 100 W (1/8 HP) in a 90 mm (3.54 in.) frame size is achieved through increased efficiency. An overall length 15 mm (0.59 in.) shorter than the conventional motor contributes to equipment downsizing. ●Rated Output Power at 60 Hz Loss Reduced Power Consumption Reduced by about 31% by about 10% ●Increased Motor Output Power Conventional Product Output Power Conventional Product K S Series 100 W (1/8 HP) 90 W (1/8 HP) when outputting 90 W (1/8 HP)

Open the catalog to page 1

Best Characteristics Achieved when Combined with an Inverter ●Wide Range of Speeds Speed can be controlled over a wide range using an inverter, from 3∼120 Hz. Also, with improved characteristics, high torque can be exerted even at low speeds. Conventional Product Continuous Operation Range 100 W (1/8 HP) Round Shaft Type Continuous Operation Range Permissible Torque Rated Torque [%] Rated Torque [%] Permissible Torque 1500 2000 2500 Speed [r/min] Speed Ratio 40:1 ●Improved Speed Stability ●Handles High-Speed Rotation (Round shaft type) Because it is a high-performance motor with little...

Open the catalog to page 2

Motors with terminal box conforming to IP66 rating for degree of protection. ●Strengthened Seal Structure for the Motor, Gearhead and Terminal Box Components ● The IP indication that shows the watertight and dust-resistant performance is specified under IEC 60529 and IEC 60034-5. IP6 6 6: Protection against strong water jets such as ocean waves 6: Completely dust-proof design ●Right-Angle Shaft Hollow Hypoid JH Gear ●Parallel Shaft Gearhead GV Gear, Round Shaft Type Gasket employed at terminal case junctions O-ring employed at terminal case/ cover junction Screws: Stainless steel Oil-shield...

Open the catalog to page 3

Utilizes a Gearhead that Excels in Both Torque and Strength ●Right-Angle Shaft Hollow Hypoid JH Gear K S Series Rated Torque [lb-in] Permissible Radial Load Uses high-strength hypoid gears Greatly increased torque and reduced noise compared to conventional products. Both the radial load and the axial load have been significantly increased, contributing to decreased equipment size and improved reliability. High Gear Ratio Product Line Oriental Motor Conventional Product Permissible Axial Load Rated Torque 2.7 Times Higher Output Power 100 W (1/8 HP) Permissible Radial Load 1291 N (290 lbs.)...

Open the catalog to page 4

• Induction Motor Right-Angle Shaft Hollow Hypoid JH Gear

Open the catalog to page 5

KnS Series Induction Motors AC Power Supply (Main power supply) • Example of System Configuration

Open the catalog to page 6

Induction Motors 30 W (1/25 HP) □80 mm (ZI3.15 in.) KIIS Series Right-Angle Hollow Shaft Hypoid JH Gear Stainless Shaft ■Specifications - Continuous Rating cTOus (§) C € •A number indicating the gear ratio is entered where the box □ is located within the product name.

Open the catalog to page 7

● Installation screws are included. ● The terminal box cable outlet can be rotated and affixed in 4 possible directions. ● A number indicating the gear ratio is entered where the box □ is located within the product name. ●Terminal Box Type Product Name 4IK30VKEST-4H □S Motor Product Name 4IK30VKEST Gearhead Product Name 4H □S Safety Cover (Included) Applicable Cable Size Outer Diameter: ϕ7∼ϕ13

Open the catalog to page 8

Induction Motors 40 W (1/19 HP) □90 mm (ZI3.54 in.) KIIS Series Right-Angle Hollow Shaft Hypoid JH Gear Stainless Shaft ■Specifications - Continuous Rating cTOus (§) C € •A number indicating the gear ratio is entered where the box □ is located within the product name.

Open the catalog to page 9

● Installation screws are included. ● The terminal box cable outlet can be rotated and affixed in 4 possible directions. ● A number indicating the gear ratio is entered where the box □ is located within the product name. Safety Cover (Included) Applicable Cable Size Outer Diameter: ϕ7∼ϕ13 (ϕ0.28∼ϕ0.51) Gearhead Product Name 5H □S Motor Product Name 5IK40VKEST

Open the catalog to page 10

Induction Motors 100 W (1/8 HP) □90 mm (□3.54 in.) KIIS Series Right-Angle Hollow Shaft Hypoid JH Gear Stainless Shaft ■Specifications - Continuous Rating cTOus (§) C € Product Name Terminal Box Type Gear Ratio O Load Position Radial Load Axial Load •The speed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is up to 20% less, depending on the load. • No built-in overheat protection device (thermal protector). When there is an overload or the output shaft is locked, use the electromagnetic switch and the...

Open the catalog to page 11

● Installation screws are included. ● The terminal box cable outlet can be rotated and affixed in 4 possible directions. ● A number indicating the gear ratio is entered where the box □ is located within the product name. ●Terminal Box Type Motor Product Name Safety Cover (Included) Applicable Cable Size Outer Diameter: ϕ7∼ϕ13 (ϕ0.28∼ϕ0.51)

Open the catalog to page 12