Catalogs >
ORIENTAL MOTOR >
Induction Motors

Induction Motors
29Pages

Catalog excerpts

Induction Motors ˾Features b Optimal for Uni-Directional Continuous Operation Induction motors are optimal for uni-directional continuous operation such as a conveyor system. ˾Safety Standards and CE Marking Standards Certification Body Standards File No. E64199 (1 Wȁ6 W Type) E64197 (15 Wȁ150 W Type) Conform to EN/IEC Standards Low Voltage Directives 2005010401150786 (Single-Phase 1 W, 3 W Type) 2003010401091525 (Single-Phase 6 W Type) 2003010401091527 (Three-Phase 6 W Type) 2003010401091522 (Single-Phase 15 Wȁ90 W Type) 2003010401091520 (Three-Phase 25 Wȁ90 W Type) 2005010401150785 (2-Pole, High-Speed Type, Single-Phase 40 Wȁ150 W Type) 2005010401150788 (2-Pole, High-Speed Type, Three-Phase 60 Wȁ150 W Type) b When the motor is approved under various safety standards, the model name on the nameplate is the approved model name. b The following products are not applicable to the table above. 4IK25GN-UT4, 4IK25A-UT4, 5IK40GN-UT4, 5IK40A-UT4, 5IK60GE-UT4F, 5IK60A-UT4F, 5IK90GE-UT4F, 5IK90A-UT4F Certification Body TÜV Rheinland

Open the catalog to page 1

Brake Pack SB50W (Sold separately) Equipped with instantaneous stopping functions, thermal protector open detection functions. Flexible Couplings (Accessories) Mounting Brackets (Accessories) Right-Angle Gearheads (Sold separately) ˾System Configuration Induction Motors Motor AC Power Supply Capacitor Cap✽ (Included) Insulating cap for capacitor terminal section. Capacitor (Included) ȜExample of System Configuration (Body) (Sold separately) Long Life/Low Noise Mounting Bracket GN-S Gearhead 4GN25S SOL4M5 Flexible Coupling MCL301012 : Required under this system. : Selectable according to...

Open the catalog to page 2

˾General Specifications of Motors b 1 W, 3 W Type Item Dielectric Strength Insulation Resistance 100 M⍀ or more when 500 VDC megger is applied between the windings and the frame after rated motor operation under normal ambient temperature and humidity. Sufficient to withstand 1.5 kV at 50 Hz or 60 Hz applied between the windings and the frame for 1 minute after rated motor operation under normal ambient temperature and humidity. Temperature Rise Temperature rise of windings are 75˚C or less measured by the resistance change method after rated motor operation under normal ambient temperature...

Open the catalog to page 3

Induction Motors ˾Specifications – Continuous Rating Model Lead Wire Type Pinion Shaft Type Round Shaft Type 0IK1A-AW2J Rated Speed r/min 1000 1200 1200 Electromagnetic Brake Motors Current Starting Torque Rated Torque b The J and U at the end of the model name indicate that the unit includes a capacitor. These letters are not listed on the motor nameplate. When the motor is approved under various safety standards, the model name on the nameplate is the approved model name. : Impedance protected ˾Product Line b Motor Type b Gearhead (Sold Separately) Model Pinion Shaft Type 0IK1GN-AW2J...

Open the catalog to page 4

˾Gearmotor – Torque Table bGearheads are sold separately. Decimal gearheads are not available. bEnter the gear ratio in the box (Ⅺ) within the model name. indicates gear shaft rotation in the same direction as the motor shaft, while the others rotate in the opposite bA colored background direction. bThe speed is calculated by dividing the motor's synchronous speed (4-pole type; 50 Hz: 1500 r/min, 60 Hz: 1800 r/min, 2-pole type; 50 Hz: 3000 r/min, 60 Hz: 3600 r/min) by the gear ratio. The actual speed is 2 - 33% less than the displayed value, depending on the size of the load. Speed r/min...

Open the catalog to page 5

ȣ Capacitor (Included with the motors) ȣ Capacitor Dimensions (mm) Induction Motors bThe direction of motor rotation is as viewed from the shaft end of the motor. CW represents the clockwise direction, while CCW represents the counterclockwise direction. bConnection diagrams are also valid for the equivalent round shaft type. ˾Connection Diagrams Reversible Motors Electromagnetic Brake Motors PE: Protective Earth Note: Change the direction of single-phase motor rotation only after bringing the motor to a stop. If an attempt is made to change the direction of rotation while the motor is...

Open the catalog to page 6

Induction Motors 1W / 3W Lead Wire Type (Gearhead sold separately) ˾Specifications – Continuous Rating 15 W Model Upper Model Name: Pinion Shaft Type Lower Model Name ( ): Round Shaft Type Terminal Box Type Dimension ባ Lead Wire Type Dimension ቢ Single-Phase 200 Single-Phase 220 Single-Phase 230 Three-Phase 200 Three-Phase 220 Three-Phase 230 Current Starting Torque Rated Torque Rated Speed b The J, U and E at the end of the model name indicate that the unit includes a capacitor. These letters are not listed on the motor nameplate. When the motor is approved under various safety standards,...

Open the catalog to page 7

Motor/ Gearhead Gear Ratio Speed r/min Motor/ Gearhead Gear Ratio Reversible Motors Speed r/min Induction Motors bGearheads and decimal gearheads are sold separately. Ⅵ bEnter the code that represents the terminal box type "T" in the box (Ⅺ) within the model name. bEnter the gear ratio in the box (Ⅺ) within the model name. indicates gear shaft rotation in the same direction as the motor shaft, while the others rotate in the opposite bA colored background direction. bThe speed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio....

Open the catalog to page 8

Mass: Motor 0.9 kg Gearhead 0.4 kg Motor Model Gear Ratio b Specify the type of the capacitor to be included by entering J, U or E in the box (Ⅺ) within Ⅵ the model name. Enter the gear ratio in the box (Ⅺ) within the model name. 0.5 70Ϯ Gearhead Model b Use cable with a diameter of ␾8 ȁ ␾12 mm. The mass and motor's dimensions (excluding the shaft section) are the same as those of the pinion shaft type. Can be connected to GN pinion shaft type. Protective Earth Terminal M4 (Lead Wire Type Only) ȣ Capacitor (Included with single-phase motors) B Bϩ10 ȣ Capacitor Dimensions (mm) Model Upper...

Open the catalog to page 9

bThe direction of motor rotation is as viewed from the shaft end of the motor. CW represents the clockwise direction, while CCW represents the counterclockwise direction. bConnection diagrams are also valid for the equivalent round shaft type. bSpecify the type of the capacitor to be included by entering J, U or E in the box (Ⅺ) within the model name. Lead Wire Type To change the rotation direction, change any two connections between U, V and W. Reversible Motors To change the rotation direction, change any two connections between R, S and T. Counterclockwise Counterclockwise Induction...

Open the catalog to page 10