Catalogs >
ORIENTAL MOTOR >
High Torque Gearheads

High Torque Gearheads
24Pages

Catalog excerpts

High Torque Gearheads Parallel Shaft Gearhead Foot Mount Type Gearhead Right-Angle Hollow Shaft Hypoid JH Gearhead Foot Mount Type JB Gearhead Parallel Shaft JV Gearhead Right-Angle Hollow Shaft Hypoid Gearhead These gearheads are designed for our compact motors of BMU and BLE2 series. They are specified with high torque and big axial and radial loads. Right-Angle Hollow Shaft Hypoid JH Gearhead ■Permissible Torque ■High Strength No torque saturation over the entire speed range. The degree of protection is IP66 which is realized by the stainless steel shaft (JH and JV gearhead). Compared to conventional gearheads 2x more Permissible Radial Load 981 N ●Stainless Steel Shaft Permissible Axial Load 261 N Gear Ratio JH gearhead conventional parallel shaft type JB gearhead (steel shaft): IP44 Foot Mount Type JB Gearhead • Parallel Shaft JV Gearhead ■High Permissible Torque Up to 518 N·m 600 Foot Mount Type Parallel Shaft with Foot Mount Type ■High Gear Ratio Flange Type Permissible Radial Load Permissible Radial Load ■High Strength Permissible Axial Load Permissible radial load Permissible Axial Load Foot Mount Type JB Gearhead Permissible axial load Permissible radial load Permissible axial load

Open the catalog to page 1

■Features of Right-Angle Hollow Shaft Hypoid Gearhead ●Downsizing ●Lower Cost Downsizes the construction by direct mounting to the conveyor. Furthermore, the concentric shaft offers more flexibility for the mounting direction. Reduction of costs and parts thanks to direct connection. Concentric Shaft Shape ● Reduction of costs ● Reduction of parts ● Reduction of coupling space Right-Angle Hollow Shaft Hypoid Gearhead Reduction of coupling space Parts reduction 90 W AC Motor Parallel Shaft Gearhead [Right-Angle Hollow Shaft Hypoid Gearhead] [Parallel Shaft Gearhead] ■Features of Foot Mount...

Open the catalog to page 2

Sold Separately 0The system configuration shown above is an example. Other combinations are also available. 3

Open the catalog to page 3

#Motor (Combination Type/Round Shaft Type) O Right-Angle Hollow Shaft Hypoid JH Geared / Foot Mount Type JB Geared / Parallel Shaft JV Geared BLM 5 200 H P K - 5 C B 50 B - L © © © ©@© @®®®©@ Motor Product Code Gearhead Product Code © #Driver BLE2D 120 - C © © ® BMUD 120 - C 2 © © ® © #Connection Cable CC 010 H BL F © © © © ©

Open the catalog to page 4

Motors, drivers and connection cables must be ordered individually. For the single-phase 100-120 VAC models, please contact the nearest Oriental Motor sales office. ©Motors O Right-Angle Hollow Shaft Hypoid JH Geared

Open the catalog to page 5

Product Name ❖ 1 Only for BLE2 series driver: The brackets ( ) indicate specification for analog setting. ❖ 2 For BMU series, the Conditions Operating ambient temperature is 0—+40°C ■The values correspond to each specification and characteristic of a stand-alone motor. ❖ 1 The rotation direction is viewed from the gear flange side (see illustration on the right). ❖ 2 The speed of the output shaft is the value of the speed divided by the gear ratio. ❖ 3 The permissible radial load can also be calculated with a formula. ^ Page 18 ❖ 4 It is also applicable when digitally setting the...

Open the catalog to page 6

■Speed – Torque Characteristics Continuous Duty Region: Continuous operation is possible in this region. Limited Duty Region: This region is used primarily when accelerating Maximum Instantaneous Torque Rated Torque Continuous Duty Region 80 Limited Duty Region Rated Torque Continuous Duty Region 0 Maximum Instantaneous Torque Limited Duty Region Torque [N·m] Maximum Instantaneous Torque Limited Duty Region Rated Torque Continuous Duty Region 0 ●The values correspond to each specification and characteristic of a motor without gearhead. The speed-torque characteristics show the values when...

Open the catalog to page 7

Right-Angle Hollow Shaft Hypoid JH Geared 200 w, 300 w■Specifications c^Dis C€ ❖ 1 The rotation direction is viewed from the gear flange side (see illustration on the right). ❖ 2 The speed of the output shaft is the value of the speed divided by the gear ratio. ❖ 3 The permissible radial load can also be calculated with a formula. ^ Page 18 ❖ 4 It is also applicable when digitally setting the deceleration time to below 0.1 seconds. ■Speed - Torque Characteristics Continuous Duty Region: Continuous operation is possible in this region. Limited Duty Region: This region is used primarily...

Open the catalog to page 8

Foot Mount Type JB Geared 200 w, 300 w■Specifications cHkw C€ ■Speed - Torque Characteristics Continuous Duty Region: Continuous operation is possible in this region. Limited Duty Region: This region is used primarily when accelerating. •200W*1*2 #300W*2 Radial Load Axial Load 10 mm 20 mm Distance from Output Shaft End Product Name ❖ 1 Only for BLE2 series driver: The brackets ( ) indicate specification for analog setting. ❖ 2 For BMU series, the Conditions Operating ambient temperature is 0—+40°C ■The values correspond to each specification and characteristic of a stand-alone motor....

Open the catalog to page 9

Parallel Shaft JV Geared 200 w, 300 w■Specifications c^Dis C€ Gear Ratio ❖ 1 The speed of the output shaft is the value of the speed divided by the gear ratio. ❖ 2 It is also applicable when digitally setting the deceleration time to below 0.1 seconds. ❖ 3 300 W Type only O Load Position Product Name ❖ 1 Only for BLE2 series driver: The brackets ( ) indicate specification for analog setting. ❖ 2 For BMU series, the Conditions Operating ambient temperature is 0—+40°C ■The values correspond to each specification and characteristic of a stand-alone motor. ■The values correspond to each...

Open the catalog to page 10

0 Overload alarm detection time- The overload alarm is generated if the operation goes beyond the continuous duty region. The detection time for this overload alarm can be set from 0.1 ~60.0 seconds. (Initial value: 30.0 Seconds) However, an alarm is generated for a maximum length of 5 seconds in the following cases. ■ If an applied load goes beyond the limited duty region ■ If the output shaft is locked

Open the catalog to page 11