Group: Oriental Motor
Catalog excerpts
High-Torque 2-Phase Stepper Motors High-Torque Combination Bipolar 2-phase Stepper Motors with Neugart Planetary Gearheads Short Delivery Time Planetary Gearheads
Open the catalog to page 1PKP Series ●For detailed information about regulations and standards, please refer to the Oriental Motor website. These products are high-torque 2-phase stepper motors. A wide variety of products are available to meet your design specifications. •Standard Type with a Resolution of 200 Steps per Revolution (Basic step angle: 1.8˚/step) •Bipolar (4 lead wires) •Encoder Types are Available •Many Motor Current Models are Available See Full Product Details Online www.orientalmotor.com ■Features Increased Torque over the Entire Speed Range from Low to High After revising the magnetic and...
Open the catalog to page 2The PLE Series from Neugart is notably light, extremely powerful, yet suitable for complex production cycles due to its low-friction bearing design and optimized lubrication. • Light & Powerful The PLE excels with its above-average weight to torque ratio, and it is 25% lighter than comparable conventional gearheads. • Efficient and Reliable With the innovative design, low backlash with high output torque is achieved. • Low Heat Generation Low-friction bearing design and optimized lubrication allows for continuous operation without sacrificing performance Use a PKP Series motor with PLE...
Open the catalog to page 3• For detailed information about regulations and standards, please refer to the Oriental Motor website. • This is a DC power supply input driver for bipolar 2-phase stepper motors. • Using this microstepping driver reduces vibration and noise. Driver Type External View Driver Installation Direction •Bipolar Driver for 2-Phase Stepper Motors •Driver for 5-Phase Stepper Motors 85 mm (3.35 in.) - Mass 20 g (0.71 oz.)~70 g (2.47 oz.) (The value differs according to the driver type.) • The driver cannot be shared by both a 2-Phase stepper motors and 5-Phase stepper motors. Each must use its...
Open the catalog to page 4■System Configuration These accessories allow the 1.8˚ Stepper Motor PKP Series to be used for various operations. An example of a system configuration with the SCX11 controller is shown below. 1.8˚ Stepper Motors PKP Series Motor Required Drive Products (Sold separately) Connection Cable Bipolar Driver A connection cable is required for connector-coupled motors. Circuit Cover Programmable Controller (Sold separately) Controller (Sold separately) PLE Gearhead (Sold separately) Screws (Sold separately) ●Example of System Configuration 1.8˚ Stepper Motors PKP Series Connection Cable ● The...
Open the catalog to page 5■Product Number
Open the catalog to page 6A connector-coupled motor requires a connection cable. Motors and connection cables must be ordered separately. • Motor O Standard Type, Standard Type with Encoder • Bipolar ❖ All PKP26_type encoder motors come with 8 mm output shaft. See drawings for details, page 18. • PLE Gearhead O Metric (motor shaft) O Inch (motor shaft) • Screws Product Name Product Name Product Name
Open the catalog to page 7Standard Type Frame Size 42 mm (1.65 in.) Bipolar 4 Lead Wires Standard Type with Encoder ■Specifications Maximum Holding Torque Rated Current Winding Resistance Product Name Basic Step Angle ● The box □ in the product name indicates the shaft A (single shaft) or B (double shaft). The box ■ in the product name indicates the encoder resolution E (200 P/R) or F (400 P/R). The box ■ in the product name indicates the encoder output circuit type L (line driver output). The voltage output type will have no " ■ " in the product name. ● See page 25 for encoder specifications. ✽Torque does not reach...
Open the catalog to page 8■Speed – Torque Characteristics (Reference Values) ◇PKP243D15/PLE40 Driver: CVD223FBR-K, Power Supply Voltage: 24 VDC, Current: 1.5 A/Phase Driver: CVD223FBR-K, Power Supply Voltage: 24 VDC, Current: 2.3 A/Phase Torque [lb-in] Torque [lb-in] Driver: CVD223FBR-K, Power Supply Voltage: 24 VDC, Current: 1.5 A/Phase Speed [r/min] Speed [r/min] Driver: CVD223FBR-K, Power Supply Voltage: 24 VDC, Current: 1.5 A/Phase Driver: CVD223FBR-K, Power Supply Voltage: 24 VDC, Current: 2.3 A/Phase Speed [r/min] Driver: CVD223FBR-K, Power Supply Voltage: 24 VDC, Current: 1.5 A/Phase Speed [r/min] Driver:...
Open the catalog to page 9Driver: CVD223FBR-K, Power Supply Voltage: 24 VDC, Current: 2.3 A/Phase Driver: CVD223FBR-K, Power Supply Voltage: 24 VDC, Current: 1.5 A/Phase Driver: CVD223FBR-K, Power Supply Voltage: 24 VDC, Current: 2.3 A/Phase Nominal Output Torque Speed [r/min] ●Data for the speed-torque characteristics is based on Oriental Motor’s internal conditions. If the conditions are changed, the characteristics may also change as a result. ●Depending on the driving conditions, a considerable amount of heat may be generated by the motor. Be sure to keep the motor case temperature at 100°C (212°F) or less. In...
Open the catalog to page 10Driver: CVD223FBR-K, Power Supply Voltage: 24 VDC, Current: 1.5 A/Phase Driver: CVD223FBR-K, Power Supply Voltage: 24 VDC, Current: 2.3 A/Phase Torque [lb-in] Speed [r/min] Nominal Output Torque Torque [N·m] Torque [lb-in] Torque [lb-in] Speed [r/min] Torque [lb-in] Speed [r/min] Nominal Output Torque Torque [lb-in] Driver: CVD223FBR-K, Power Supply Voltage: 24 VDC, Current: 2.3 A/Phase Driver: CVD223FBR-K, Power Supply Voltage: 24 VDC, Current: 1.5 A/Phase Torque [lb-in] Driver: CVD223FBR-K, Power Supply Voltage: 24 VDC, Current: 2.3 A/Phase Driver: CVD223FBR-K, Power Supply Voltage: 24...
Open the catalog to page 11Product Name • Standard Type with Encoder Product Name O Encoder Connection Cable (Sold Separately) Product Name Applicable Encoder Voltage Output Line Driver Output •Applicable Connector OVoltage Output • Connection Cable (Sold separately) O Connection Cable for Motor Product Name ^4 Motor Leads UL Style 3265, AWG22 ■Inner Wiring Diagram of Motor Wiring Diagram No.: Model A© • Refer to page 25 for inner wiring diagram of motor.
Open the catalog to page 12• Use screw set P00027 (sold separately) to attach Motor and Gearhead.
Open the catalog to page 13Standard Type Frame Size 56.4 mm (2.22 in.) Bipolar 4 Lead Wires Standard Type with Encoder ■Specifications Maximum Holding Torque Product Name Rated Current Winding Resistance Recommended Driver Product Name✽ Basic Step Angle ● The box □ in the product name indicates the shaft A (single shaft) or B (double shaft). The box ■ in the product name indicates the encoder resolution E (200 P/R) or F (400 P/R). The box ■ in the product name indicates the encoder output circuit type L (line driver output). The voltage output type will have no " ■ " in the product name. ●See page 25 for encoder...
Open the catalog to page 14All ORIENTAL MOTOR catalogs and technical brochures
-
Product Guide
36 Pages
-
Product Guide
36 Pages
-
Linear & Rotary Actuators
11 Pages
-
Rack and Pinion System L Series
28 Pages
-
DRS series
2 Pages
-
DGII
2 Pages
-
EH series
12 Pages
-
Servo Motors
7 Pages
-
DSC Series
76 Pages
-
Motors Torque
6 Pages
-
BLH Series
36 Pages
-
Electric CylindersEAC Series
2 Pages
-
DSC Series
11 Pages
-
Overview of Standard AC Motors
21 Pages
-
BLE2 Series Brushless DC Motors
18 Pages
-
BMU Series Brushless DC Motors
18 Pages
-
Catalog Overview
24 Pages
-
BXII Series
31 Pages
-
RKII Series
51 Pages
-
AZ Series
10 Pages
-
CVK Series
24 Pages
-
Stepper Motors
33 Pages
-
Universal Controller, SCX11
4 Pages
-
Standard AC Motors
9 Pages
-
Servo motors
9 Pages
-
Stepping Motors
23 Pages
-
Cooling Module
8 Pages
-
KII Series
16 Pages
-
LS Rack and Pinion Systems
1 Pages
-
RK Series
4 Pages
-
AS Series
4 Pages
-
AR Series
4 Pages
-
Controllers for Stepping Motors
18 Pages
-
AC Motor Systems
62 Pages
-
VEXTA Brushless DC Motors
60 Pages
-
AC Motor Accessories
16 Pages
-
Clutch & Brake Motors
8 Pages
-
Electromagnetic Brake Motors
44 Pages
-
Reversible Motors
36 Pages
-
Induction Motors
54 Pages