Catalogs >
ORIENTAL MOTOR >
EZS Series

EZS Series
44Pages

Catalog excerpts

Oriental motor (RoHS) RoHS-Compliant Motorized Linear Slides EZSII Series

RoHS-Compliant Motorized Linear Slides Series The high-precision, compact body was made possible by adopting a rolled ball screw and guide frame structure. The compact design facilitates installation and wiring to your system for added convenience. ˾Features b Adopting a Closed-Loop Stepping Motor, This Linear Slide Eliminates Misstep and Hunting, while Attaining High-Speed and High-Response Operation. The linear slide has no hunting problem upon stopping. The vibration and noise levels have been lowered by employing advanced technology that produces smoothness comparable to a microstep...

Open the catalog to page 2

˾General Specifications of Motor ˾Safety Standards and CE Marking b General specifications of controller ➜ Page 31 Power Supply This is the value after rated operation under normal ambient temperature and humidity. Insulation Resistance 100 M⍀ or more when 500 VDC megger is applied between the following places: ⅐ Motor case−Motor/Sensor windings ⅐ Motor case−Windings of electromagnetic brake (Only for electromagnetic brake type) Dielectric Strength Sufficient to withstand the following for 1 minute: ⅐ Motor case−Motor/Sensor windings 0.5 kVAC 50 Hz ⅐ Motor case−Windings of electromagnetic...

Open the catalog to page 3

Combining all functions needed to operate a linear slide in positioning operations ˾Features b Positioning Data of up to 63 Points Can be Set with Ease Position data can be set in one of three methods, as specified below (when the controller is used in the controller mode). ቢEnter the desired travel (mm) directly. b Two Positioning Data Settings You can set positioning data in the absolute mode or incremental mode, depending on your preferred movement of the equipment. ȣ Absolute Mode: Each position is set as the absolute position with respect to the reference point. This is suitable when...

Open the catalog to page 4

b Area Output Function b Operation Using External Pulse Input A signal is output when the linear slide table enters a set area arbitrarily set along the stroke. One set area can be set. The can be combined with your existing controller to serve as a driver controlling the linear slide by pulse input. ON Area Output Signal OFF Teaching Function Monitoring Function Pause Function Area Output Function Absolute Type Sensorless Return to Home Return to Home Using Sensor ✽ Data must be set from the teaching pendant or data setting software. bNormal System Configuration Controller Mode The linear...

Open the catalog to page 5

˾Functions of Teaching Pendant (EZT1) and Data Editing Software (EZED2) The teaching pendant and data editing software are available. Choose an appropriate accessory based on the required functions. b Teaching Pendant (EZT1)/Data Editing Software (EZED2) Function Comparison Table Teaching Pendant (Sold separately) Cable of Teaching Pendant Operation Data Monitoring I/O & Alarm History Monitoring Waveform Monitoring Test Operation Data Copy Printing Function Data Editing Software (Model: EZED2) Teaching Function (Direct/Remote) Teaching Pendant (Model: EZT1) Cable Length Display Emergency...

Open the catalog to page 6

Selection of Motorized Linear Slides Power Supply Voltage Lead Maximum Load Moment [N⅐m] Linear Slide Size Linear Slide Width ϫ Height 60 50 Maximum Transportable Mass in Horizontal Direction [kg] 30 25 Maximum Transportable Mass in Vertical Direction [kg] Repetitive Positioning Accuracy [mm] Electromagnetic Brake With electromagnetic brake or without electromagnetic brake are available ✽ For the single-phase 100-115 VAC models, please contact the nearest Oriental Moto

Open the catalog to page 7

Selection Calculations After you have determined which series to use, select an appropriate model. Select a linear slide of the size that satisfies your desired condition. Select an appropriate model by following the steps below. (1) Select a Linear Slide Satisfying the Transportable Mass By referring to "Ⅵspecifications of linear slide," select a linear slide satisfying the transportable mass. Condition: Drive a work of 15 kg over a horizontal distance of 400 mm within 1.5 seconds. EZS4: Specifications of Width 74 mm ϫ Height 50 mm, 24 VDC Linear Slide ˾Specifications of Linear Slide Drive...

Open the catalog to page 8

(3) Check the Operating Speed and Acceleration of the Linear Slides The time calculated from "Ⅵpositioning distance – positioning time" assumes the operating speed and acceleration that achieve the shortest positioning time. Check the specific operating speed and acceleration at which to drive the linear slides based on the time calculated in step (2). b Operating Speed and Acceleration of the Linear Slides Check the operating speed and acceleration by referring to "Ⅵpositioning distance – operating speed" and "Ⅵpositioning distance – acceleration." If the identified speed exceeds the...

Open the catalog to page 9

˾Positioning Distance – Operating Speed, Positioning Distance – Acceleration b EZS3DⅪ-K (Lead 12 mm, 24 VDC) Maximum Speed by Stroke Max. Speed [mm/s] 600 550 460 400 ț Positioning Distance – Acceleration 20 16 Maximum Speed by Stroke Stroke [mm] 50ȁ550 600 650 700 ț Positioning Distance – Acceleration 20 Load Mass 0 kg 2 kg 3.5 kg ȣ Vertical Installation ț Positioning Distance – Operating Speed ȣ Horizontal Installation ț Positioning Distance – Operating Speed Maximum Speed by Stroke ț Positioning Distance – Acceleration 20 16 Maximum Speed by Stroke Stroke [mm] 50ȁ550 600 650 700 ț...

Open the catalog to page 10

Maximum Speed by Stroke ț Positioning Distance – Acceleration 20 16 Maximum Speed by Stroke Stroke [mm] 50ȁ500 550 600 650 700 ț Positioning Distance – Acceleration 20 Load Mass 0 kg 3.5 kg 7.5 kg ȣ Vertical Installation ț Positioning Distance – Operating Speed ȣ Horizontal Installation ț Positioning Distance – Operating Speed Maximum Speed by Stroke Stroke [mm] 50ȁ550 600 650 700 ț Positioning Distance – Acceleration 20 18 ț Positioning Distance – Acceleration ȣ Vertical Installation ț Positioning Distance – Operating Speed Operating Speed [mm/s] Maximum Speed by Stroke ȣ Horizontal...

Open the catalog to page 11