Catalogs >
Ophir Optronics >
Very High Power Water Cooled Thermal Sensors 100w to 30km

Very High Power Water Cooled Thermal Sensors 100w to 30km
1 / 1Pages

Catalog excerpts

Very High Power Water Cooled Thermal Sensors 100w to 30km - 1

1.1.2.7 High Power Thermal Sensors 1.1.2.7.4 Very High Power Water Cooled Thermal Sensors 100W to 30kW 30K-W-BB-74 with optional scatter shield Features ֺ ֺ Very high powers ֺ ֺ Water cooled ֺ ֺ Up to 30kW ֺ ֺ Up to Ø74mm aperture Absorber Type Spectral Range µm (a) Aperture mm Power Range Power Scales Power Noise Level Backscattered Power (b, e) Maximum Average Power Density kW/cm2 Response Time with Meter (0-95%) typ. s Power Accuracy +/-% Linearity with Power +/-% Cooling Minimum Water Flow Rate Beam deflector + broadband absorber 0.8 - 2, 10.6 Ø45mm 100W – 11kW 11kW / 6kW / 600W 1W ~3.5% without Scatter Shield, ~1% with Scatter Shield See note (c) and table (1) below 2.7 5 (a) 2 water (d) 10 liter/min at full power, proportionally less at lower power. Min flow rate 2 liter/min (d) Water Pressure Requirements at Max Flow Rate Pressure drop across sensor ~0.2MPa. Quick connector for 3/8” OD nylon tubing 5 meters 4.5 V3 7Z02756 Water Connectors (e) Cable Length Weight kg Version Part number Notes: (a) Calibrated at 1.064μm and 10.6μm. For other wavelengths in the range 0.8 – 2μm add up to ±2% to the calibration error When scatter shield is installed, use the NIRS setting to compensate for slightly higher reading. When not installed, use the NIR setting Beam deflector + broadband absorber 0.8 - 2, 10.6 Ø74mm 100W – 30kW 30kW / 6kW / 600W 1W ~4.3% without Scatter Shield, ~1.3% with Scatter Shield 10kW/cm² anywhere in the beam (c) 7 5 (a) 2 water (d) 25 liter/min at full power, proportionally less at lower power. Min flow rate 6 liter/min (d) Pressure drop across sensor ~0.2MPa. Pressure drop across 8 meters of ½” tubing with 9.5mm ID is ~0.3MPa. Quick connector for ½” OD nylon tubing 10 meters 19 V2 7Z02757 Calibrated at 1.07µm. For other wavelengths in the range 0.8 – 2µm add up to ± 2% to the calibration error When scatter shield is installed, use the 107S laser setting to compensate for the slightly higher reading. When not installed, use the 107 setting For circular beam centered within ¼ of beam diameter. IMPROPERLY CENTERED BEAM CAN CAUSE DAMAGE TO SENSOR. Maximum tilt angle ±5 degrees. For rectangular beam please consult Ophir representative Water temperature range 15-30°C. Water temperature rate of change <1°C/min For further information and options see Accessories for High Power Sensors on pages 59, 60 & 61 Beam diameter Max power density Max energy density 1ms pulse width 3ms pulse width 10ms pulse width 2 30J/cm2 60J/cm2 150J/cm2 <15mm 10kW/cm 15 - 20mm 7kW/cm2 20J/cm2 40J/cm2 100J/cm2 20 - 40mm 5kW/cm2 15J/cm2 30J/cm2 70J/cm2 2 2 2 40 - 45mm 4kW/cm 12J/cm 25J/cm 60J/cm2 Notes: (b) Notes: (c) Notes: (d) Notes: (e) Table: (1) (4x) M4x8 deep Mounting Threads (4x) M6x10 deep Mounting Threads (2x) Quick Connect Fitting for 3/8 Plastic Hose Front Side (4x) M6x10 deep Mounting Threads (4x) M4x8 deep Mounting Threads ADJUSTABLE 180-275 (2x) 1/4" NPT Thread Size Rear Side With optional Scatter Shield With optional scatter shield (2x) Quick Connect Fitting for 1/2" Nylon Tubing 300 Front FrontSide Side Rear Side Rear Side With Optional Scatter Shield With optional scatter shield 55 For latest updates please visit our web

Open the catalog to page 1