Stand Specs
1Pages

{{requestButtons}}

Catalog excerpts

Stand Specs - 1

Warranty 1. This product is covered by a warranty for a period of one year from the date of purchase. 2. This warranty covers free-of-charge repair for defects judged to be the responsibility of the manufacturer, i.e., defects occurred while the product is used under normal operating conditions according to descriptions in this manual and notices on the unit label. 3. For free-of-charge repair, contact either your sales representative or our sales office nearby. 4. The following failures will be handled on a fee basis even during the warranty period, (a) Failures occurring through misuse, mis-operation, or modification (b)Failures occurring through mishandling (dropping) or transportation (c) Failures occurring through natural calamities (fires, earthquakes, flooding, and lightening), environmental disruption, or abnormal voltage. * For repairs after the warranty period expired, contact your sales representative or our sales office nearby. ONO SOKKI ST-022 / ST-044B Using Ono Sokki Gauge Stands This gauge stand uses a ceramic measurement base, which provides excellent durability and resistance to wear, and is free from problems of rust and marring, enabling it to be used for a long period with high performance. (D Applicable stem diameter of linear gauges To accommodate linear gauges with the stem diameter except the above to the ST-044B,a stand bush may be required. # AA-891 I For 0 8 mm stem diameter (D When mounting the linear gauge to or removing it from the stand, use knob A. Remove the gauge while holding it with the hand and loosening knob A. (D When the arm of stand is moved at up and down, hold the arm with the hand, free up the vertical position by loosening knob B and adjust knob C. ® Before using, be sure to wipe dirt, oil, or other impurities from the measurement base, using a soft cloth. The arm support pillar sliding surfaces are highly susceptible to rust and should be coated with grease or machine oil after use to prevent such corrosion. This is particularly important if the stand is not to be used for a long period. © It is recommended that the signal cable from the linear gauge sensor be clamped at the side of the arm. KnobB Cable clamp a \KnobC Arm X :Parallel level between the bottom surface of the base and upper surface of measurement table Y : Right angle level between the bottom surface of the base and pole Z : Right angle level between bottom surface of base and fixing hole XZ : Right angle level between upper surface of measurement table and fixing hole (Calculation from the sum of X and Z.)

Open the catalog to page 1

All Onosokki catalogs and technical brochures

  1. SE-1200

    2 Pages

  2. HR-6800

    3 Pages

  3. GE-1400

    2 Pages

  4. sr-2200

    8 Pages

  5. MI Series

    6 Pages

  6. GS-7710

    2 Pages

  7. GS-5050

    2 Pages

  8. GS-1713/1730

    3 Pages

  9. GS-1713/1730

    4 Pages

  10. BS Series

    2 Pages

  11. DG-4000

    4 Pages

  12. EG-225

    2 Pages

  13. RP-7400

    2 Pages

  14. LG-9200

    2 Pages

  15. LG-9200

    2 Pages

  16. LG-9200

    2 Pages

  17. SE-1100

    4 Pages

  18. HT-6200

    4 Pages

  19. HT-5500

    3 Pages

  20. HT series

    3 Pages

  21. DG-525H

    6 Pages

  22. DG-3610

    2 Pages

  23. FT-7200

    8 Pages

  24. CT-6520B

    4 Pages

  25. TM-3100 Series

    12 Pages

  26. HT-5100

    4 Pages

  27. HT-3100

    4 Pages

  28. FV-1300

    4 Pages

  29. DS-3000

    2 Pages

  30. SE 2500

    4 Pages

  31. SE 1620

    2 Pages

  32. SE 1520

    2 Pages

  33. SE 1100

    4 Pages

  34. CT - 6520

    4 Pages

  35. FT-2500

    8 Pages

  36. SE-1620

    2 Pages

  37. GE-1200

    2 Pages

Archived catalogs

  1. HT-6200

    4 Pages

  2. HT-6100

    4 Pages

  3. SE-2500

    4 Pages

  4. HT-6100

    4 Pages