Catalogs >
OMRON >
NE1A-SCPU0[]-EIP

NE1A-SCPU0[]-EIP
1 / 8Pages

Catalog excerpts

Safety Network Controller Directly Connected to SYSMAC CS/CJ Series via EtherNet/IP • Monitors safety systems via EtherNet/IP. • Equipped with master functions of CIP Safety on DeviceNet. • Does not require external devices for connecting Safety Network Controller and EtherNet/IP. • Increased maintainability in combination with OMRON’s EtherNet/IP compatible PLC. • ISO13849-1 (PLe) and IEC 61508 SIL3 certification. Ordering Information Name No. of I/O points Safety inputs Test outputs Safety outputs Safety Network Controller 40 8 8 NE1A-SCPU02-EIP 1.1 Note: 1. The standard NE1A Controllers are equipped with spring-cage terminal blocks, but other screw terminal blocks are available if desired, e.g., to replace previous terminals. 2. Use the Network Configurator Ver. 2.2 or later to make NE1A-SCPU0@-EIP settings. Specifications Certified Standards Certification body Specifications Standards DeviceNet communications power supply voltage Unit power supply voltage (V0) * 1 I/O power supply voltage (V1, V2) * 1 11 to 25 VDC (Supplied via communications connector.) Communications 24 VDC, 15 mA power supply Current Internal circuit 24 VDC, 280 mA consumption power supply I/O power supply *2 24 VDC, 40 mA (Input) 24 VDC, 80 mA (Input) 120 mA (Output) 150 mA (Output) Overvoltage category Noise immunity Vibration resistance Shock resistance Mounting method Ambient operating temperature Ambient operating humidity Ambient storage temperature -40 to 70°C Degree of protection Serial interface *1. V0-G0: Internal control circuit V1-G1 (G): For external input device, test output V2-G2 (G): For external output device *2. Not including power consumption for external devices.

Open the catalog to page 1

NE1A-SCPU0@-EIP Safety Input Specifications Test Output Specifications Input type Output type 11 VDC min. between each terminal and ground 5 VDC min. between each terminal and ground Rated output current 1.2 V max. between each output terminal and V1 Input current Leakage 0.1 mA max. current * The maximum current for simultaneously ON outputs is 1.4 A. (T0 to T3: NE1A-SCPU01 (-V1) (-EIP), T0 to T7: NE1A-SCPU02) (EIP) A 15 to 400-mA, 24-VDC external indicator can be connected to T3: NE1A-SCPU01 (-V1) (-EIP), T3, and T7: NE1A-SCPU02 (-EIP). Safety Output Specifications Output type Rated...

Open the catalog to page 2

NE1A-SCPU0@-EIP Function Function Blocks NE1A-SCPU@-EIP series Controller support the following logic functions and function blocks. Logic Functions Name Function Blocks Function list entry Function list entry Emergency Stop Monitoring Light Curtain Monitoring Light Curtain Monitoring Safety Gate Monitoring Safety Gate Monitoring Off-Delay Timer Off-Delay Timer On-Delay Timer On-Delay Timer User Mode Switch Monitoring User Mode Switch External Device Monitoring Enabling Switche Monitoring Enable Switch Pulse Generator Pulse Generator Multi Connector Multi Connector

Open the catalog to page 3

NE1A-SCPU0@-EIP Internal Circuit Diagrams Power supply terminal for internal circuit The two V0 terminals are internally connected. Power supply terminal for internal circuit The two G0 terminals are internally connected. Power supply terminal for external input device and test output Power supply terminal for external input device and test output Power supply terminal for external output device Safety Input Circuit Test Output Circuit Internal Circuit Power supply terminal for external output device Safety input terminal Test output terminal Connected to IN0 to IN15 safety inputs. Each...

Open the catalog to page 4

NE1A-SCPU0@-EIP Safety Precautions Refer to the "Safety Precautions for All CIP Safety on DeviceNet Systems" for precautions. Be sure to read the following user's manual for other details required for correct use of the Safety Network Controller. CIP Safety on DeviceNet Safety Network Controller User's Manual (Cat. No. Z916) Functions Supported According to Unit Version Model Selecting a rising edge as the reset condition for Reset and Restart function blocks Using local I/O status in logic programming Using overall Unit status in logic programming Program execution wait functions...

Open the catalog to page 6

NE1A-SCPU0@-EIP Unit Versions and Network Configurator Versions Network Configurator version 2.2@ or higher must be used when using a NE1A-SCPU01-EIP or NE1A-SCPU02-EIP. Network Configurator version 3.3@ or higher must be used when using a NE1A-SCPU01-EIP or NE1A-SCPU02-EIP Safety Logic Controller with unit version 1.1. ❍ : Applicable, ×: Not applicable Model *1: It can be used as unit version 1.0. Note: 1. Users who use Network Configurator version 1.5@ or earlier can upgrade to version 1.6@ at no charge. 2. When using Network Configurator version 1.6@, there are no operational differences...

Open the catalog to page 7

Terms and Conditions Agreement Read and understand this catalog. Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. Warranties. (a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron disclaims all other warranties, express or implied. (b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS...

Open the catalog to page 8