Catalogs >
OMEGA >
MODULAR CONTROLLER SERIES MASTER

MODULAR CONTROLLER SERIES MASTER
3Pages

Catalog excerpts

MODULAR CONTROLLER SERIES MASTER Starts at Performs Hierarchical Control of Other Modules in the Modular Controller Series Provides Power and Communications to Modules Through Backplane Connector Stores Module Configuration Information, and Automatically Reprograms Replaced Modules Extensive Built-In Driver List Allows Easy Data Mapping to PLCs, PCs, and SCADA Systems Independent Serial Ports Provide Virtually Unlimited Integration Methods 10 Base-T/100 Base-Tx Ethernet Connection Provides Networking Capability Supports Up To 16 Modular Controller Series Modules Supported By Crimson 2.0 Software CSMSTRV2, $308, shown smaller than actual size. The Model CSMSTRV2 is a communications and control platform designed for use with Modular Controller Series slave modules. The CSMSTRV2 uses a proprietary high speed serial protocol to communicate, via backplane connection, with up to 16 slave modules. Through the same connection, the Master also provides power to the modules. When powered up, the CSMSTRV2 automatically identifies and addresses connected slave modules. By storing the configuration information of all of the modules, the CSMSTRV2 is able to automatically configure modules if they are replaced. Power: 24 Vdc ± 10% 400 mA min (1 module) 3 A max (16 modules) Must use Class 2 or SELV rated power supply Communications: USB/PG Port: Adheres to USB specification 1.1. Device only using Type B connection Serial Ports: Format and Baud Rates for each port are individually software programmable up to 115,200 baud RS232/PG Port: RS232 port via RJ12 COMMS Ports: RS422/485 port via RJ45, and RS232 port via RJ12 DH485 TXEN: Transmit enable; open collector, VOH = 15 Vdc, VOL = 0.5 V @ 25 mA max Ethernet Port: 10 BASE-T / 100 BASE-TX RJ45 jack is wired as a NIC (Network Interface Card) LEDs: STS: Status LED indicates condition of master TX/RX: Transmit/Receive LEDs show serial activity Ethernet: Link and activity LEDs Memory: On-Board User Memory: 4 Mb of non-volatile flash memory. On-board SDRAM: 2 Mb Environmental Conditions: Operating Temperature Range: 0 to 50°C (32 to 122°F) Storage Temperature Range: -30 to 70°C (-22 to 158°F) Operating and Storage Humidity: 80% max relative humidity, non-condensing, from 0 to 50°C Vibration According to IEC 68-2-6: 5 to 150 Hz, in X, Y, Z direction for 1.5 hours, 2 g’s. Shock According to IEC 68-2-27: Operational 25g, 11ms in 3 directions Altitude: Up to 2000 meters The Master provides high-speed RS232/422/485 communication ports and an Ethernet port for connection to PCs, PLCs, and SCADA systems. An extensive list of master and slave protocol drivers are available to allow the CSMSTRV2 to share and exchange variable data with external devices. The 10 Base-T/100 Base-TX Ethernet port can also be used to connect and share data with other devices at high speeds. The CSMSTRV2 was designed as a direct replacement for the original CSMSTRSE. This new model provides benefits such as support via Crimson 2.0 software, which allows configuration files to be uploaded. To save programming time, files originally created in Crimson 1.0 (.cdb files) may be imported into Crimson 2.0. The design of the Modular Controller Series high density packaging and DIN rail mounting saves time and panel space. The controller snaps easily onto standard top hat (T) profile DIN rail. The CSMSTRV2 is programmed with Crimson 2.0 software for Windows® 2000 or later platforms. The software is an easy to use, graphical interface which provides a means of communication configuration, as well as commissioning and calibration of new systems.

Open the catalog to page 1

To Order (Specify Model Number) Construction: Case body is burgundy high impact plastic and stainless steel. Installation category I, pollution degree 2 Power Connection: Removable wire clamp screw terminal block Wire Gage Capacity: 24 AWG to 12 AWG Torque: 4.45 to 5.34 in/lb (0.5 to 0.6 N-m) Mounting: Snaps onto standard DIN style top hat (T) profile mounting rails according to EN50022 -35 x 7.5 and -35 x 15. Certifications and Compliances: Safety: UL Listed, File #E302106, UL508, CSA 22.2 No. 14-M05 LISTED by Und. Lab. Inc. to U.S. and Canadian safety standards IEC 61010-1, EN 61010-1:...

Open the catalog to page 2

Your One-Stop Source for Process Measurement and Control! UNITED STATES Deckenpfronn, Germany UNITED KINGDOM Manchester, England More than 100,000 Products Available! Calibrators, Connectors, General Test and Measurement Instruments, Handheld Instruments for Temperature Measurement, Ice Point References, Indicating Labels, Crayons, Cements and Lacquers, Infrared Temperature Measurement Instruments, Recorders, Relative Humidity Measurement Instruments, PT100 Probes, PT100 Elements, Temperature & Process Meters, Timers and Counters, Temperature and Process Controllers and Power Switching...

Open the catalog to page 3