Catalogs >
OMEGA AIR d.o.o. Ljubljana >
Heatless regenerated adsorption dryers - B-DRY, F-DRY

Heatless regenerated adsorption dryers - B-DRY, F-DRY
8Pages

Catalog excerpts

Heatless regenerated adsorption dryers

B-DRY / F-DRY - Heatless regenerated adsorption dryers Four individually controlled valves To provide optimum control over the complete drying process four high quality electromagnetic valves are used. Individual control of each valve results in column switch-over without any pressure peaks. Compact control blocks Compact and robust design of upper and lower control valve block assures reliable operation. Purge air line is mounted on upper check valve block so that purge air nozzle can be replaced if required. During maintenance complete block can be removed from the dryer in one piece. Two...

Open the catalog to page 2

Heatless regenerated adsorption dryers - B-DRY, F-DRY - 3

ADSORPTION DRYER Compressed air contains contaminants such as water, oil and particulates which must be removed or reduced to the acceptable level based on specific application requirements. Standard ISO8573-1 specifies air purity/quality classes for these contaminants. Humidity (water vapor content) is expressed in the terms of Pressure Dew Point (PDP), where Dew point is the temperature at which air is 100% saturated with moisture. When the temperature of the air is reduced to or below the dew point, condensation will occur. Typical applications for the adsorption dryers are outdoor...

Open the catalog to page 3

Heatless regenerated adsorption dryers - B-DRY, F-DRY - 4

B-DRY / F-DRY - Heatless regenerated adsorption dryers Compressed air inlet (wet air) Compressed air outlet (dry air) Column filled with dessicant Two layer desiccant bed Controller Solenoid valve Expansion silencer Non-returning valve Nozzle Pressure manometer Inlet air filter Outlet air filter Automatic condensate drain Flow distribution insert Cable for solenoid valve (optional) Dew point sensor (optional) B-DRY and F-DRY adsorption dryers have been designed for continuous separation of water vapor from the compressed air thus reducing the pressure dew point. Adsorption takes place under...

Open the catalog to page 4

Heatless regenerated adsorption dryers - B-DRY, F-DRY - 5

B-DRY / F-DRY - Heatless regenerated adsorption dryers

Open the catalog to page 5

Heatless regenerated adsorption dryers - B-DRY, F-DRY - 6

B-DRY / F-DRY - Heatless regenerated adsorption dryers Easy maintenance When FIX operating cycle is selected or when the dryer is not equipped with a dew point sensor it will operate in pre-set operating cycles meaning length of adsorption and regeneration will be fixed. Energy losses are directly related with an amount of purge air which is used for regeneration. B-DRY and F-DRY energy losses have been optimized due to the 10 minute operating cycle: Upper and lower control valve can be removed from the dryer in one piece. All components that are subject to wear are easily accessible and...

Open the catalog to page 6

Heatless regenerated adsorption dryers - B-DRY, F-DRY - 7

B-DRY / F-DRY - Heatless regenerated adsorption dryers Technical data TECHNICAL DATA B-DRY 110-1000 Nominal volume flow Connection IN/OUT TECHNICAL DATA F-DRY 1200-6500 Nominal volume flow Connection IN/OUT Voltage, frequency Power consumption Protection class Filter (inlet)* Filter (outlet) Operating temperature range Operating pressure range OPERATING PRESSURE - CORRECTION FACTORS - COP Operating pressure [bar] Operating pressure [psi] Correction factor COP OPERATING TEMPERATURE - CORRECTION FACTORS - COT Operat. temperature [°C] DEW POINT - CORRECTION FACTORS - CD 55 Refers to 1bar(a)...

Open the catalog to page 7