International Sales Hotline Domestic Sales Hotline 邮箱(E-mail): [email protected] 官方网站: www.oke-carbide.com 总部地址：湖南省株洲市炎陵县中小企业创业园创业路（P.C.412500） 分公司地址：湖南省株洲市芦淞区创业四路8号（P.C.412008） Head Office Add：Chuangye Rd,Chuangye Park for SMEs,Yanling County,Zhuzhou,Hunan,China. Branch

硬质合金圆棒Cemented Carbide Rods 牌号介绍Grade Introduction 牌号推荐Grade Selection Guide 公制长棒Solid Rods-Metric 英制长棒Solid Rods–Inch 精磨倒角短棒（英制）Ground Rods with Chamfer-Inch 精磨倒角短棒（公制）Ground Rods with Chamfer-Metric 精磨倒角短棒（DIN）Ground Rods with Chamfer-DIN 木工用硬质合金圆棒Wood cutting 木工用硬质合金圆棒牌号介绍 Carbide Rod Grades for Wood Cutting Cutting Experimental Data

责 任 铸 就 卓 越 O bligation K eeps E xcellence Cobalt Content (%) 用于制作通用加工钻头，立铣刀，特别适用于不锈 钢，耐热合金，铸铁等 Common-use drill and endmill are recommended. Especially suitable for cutting stainless, heat-resistant alloy,cast iron. 用于制作立铣刀，特别适用于不锈钢，耐热合金， 铸铁等 Used to make vertical milling cutter, especially suitable for stainless steel, heat-resistant alloy, cast iron, etc 用于制作钻头，立铣刀，适用于普通合金钢 （HRC<48）,灰口铸铁，不锈钢和耐热合金 Drill and endmill are recommended. Suitable for cutting general steel(HRC<48),grey cast iron, stainless steel and heat-resistant alloy. 用于制作钻头，立铣刀和旋转锉刀，特别适用于加 工有色金属和石墨制品（需涂层） Drill， endmill and burr...

毛坯Unground ФD(mm) 公差(Tol.) 精磨Ground ФD(mm) 粗加工Roughing 精加工Finishing 复合材料 Composite Material 高硬材料 Hardened Material 耐热合金 Heat Resistance Material 可用 Acceptable★优选 Good★ ★涂层 Coating● 粗加工Roughing 精加工Finishing

毛坯Unground ФD(mm) 精磨Ground ФD(mm) 毛坯Unground ФD(mm) 范围(Range) 精磨Ground ФD(mm)

O bligation K eeps E xcellence

O bligation K eeps E xcellence

显微组织 Microstructure 切削应用 Cutting Applications 实木（软木、硬木） Wood(Soft wood 、 Hard wood) Co:8%, WC balance Ultrafine grain 1.0-1.2um 3 WP03材质和A公司材质磨损值对比 Wean comparison of WP03 and A-GRADE 切削应用 Cutting Applications 数控雕刻机 CNC Engraving Machine 切削刀具 Cutting Tool 显微组织 Microstructure 切削设备 Cutting Machine 强度 TRS 切削应用 Cutting Applications 切削材质 Cutting Material 晶粒度 Grain size 密度 Density

O bligation K eeps E xcellence 被测圆柱面任一正截面的圆周必须位于 半径差为公差值0.03的两同心圆之间 The extracted (actual) circumferential line, in any crosssection of the cylindrical and conical surfaces, shall be contained between two co-planar concentric circles, with a difference in radii of 0.03. 公差带是半径差为公差值t的两同轴 圆柱面之间的区域 The tolerance zone is limited by two coaxial cylinders with a difference in radii of t. 公差带是在同一正截面上， 半径值差为公差值t的两同心圆之间的区域 The tolerance zone, in the considered cross-section, is limited by twoconcentric circles with a difference in radii of t. 公差带是在同一正截面上， 半径值差为公差值t的两同心圆之间的区域 The tolerance zone, in the...

O bligation K eeps E xcellence Surface Roughness of Rods 镜面棒材 Polished Rods 亚光洁度 Dull Finished 精磨棒材 Ground Rods 圆度 当被测要素围绕公共基准线A-B（公共基准轴线） 旋转一周时，在任一测量平面内的径 向圆跳动均不得大于0.1 The extracted (actual) line in any cross-section plane perpendicular to common datum straight line A-B shall be contained between two coplanar concentric circles with a difference in radii of 0.1. Roundness Tolerance 精磨圆棒圆度标准均为0.002 mm The standard roundness tolerance of the ground rod is 0.002 mm. 公差带是在垂直于基准轴线的任一半径 位置的测量平面内、半径差为公差值t 且圆心在基准轴线上的两同心圆之间的区域 The tolerance zone is limited within any cross-section perpendicular to the...

责 任 铸 就 卓 越 O bligation K eeps E xcellence