Oiles Drymet ST ……………………………………P.141 Oiles Drymet LF ……………………………………P.151 Oiles LF Guides ………………………………… P.164 Oiles Techmet B ………………………………… P.166 Oiles Techmet E ………………………………… P.169 Oiles Toughmet ………………………………… P.170 Oiles Toughmet D ……………………………… P.173 Oiles Hiplast N/E ……………………………

Oil-impregnated polyacetal multi-layer bearings with back metals Test data Journal rotation test Feature • Serviceable without the need for lubrication and demonstrates low coefficient of friction and superior load performance. • Demonstrates superior wear resistance in applications where oil film is seldom produced such as reciprocating motions, oscillation, frequent starts and stops, etc. • Thin bearing allows compact design. • Superior dimensional stability, mechanical strength, and thermal conductivity. • The standard products and plate material of various sizes are available. Service range...

Press-fit force Inner diameter of the guide ring should be the size so that the bushing can be inserted by hands. Length of the guide ring should be more than one-third of the bushing, or if possible, it should be the same length as the bushing. The dimension of mandrel should be calculated from table below. Dimension of bushing Press-fit smoothly with hydralic (pressure), pneumatic pressure, or a vice. Mandrel Bushing Guide ring Avoid press-fit by use of impact such as use of a hammer. It might induce damage of the bushing, or change the size of the inner diameter after press-fit. Press-fit...

Technical Product Corporate Profile Information Slide Shifter Air Bearings Metallic Bearing BMBEBBKBBaBalBM Plastic Bearing Information Selection Guide Part No. Mating shaft Bushing thick bushingT a: O.D. chamfering for the bushing I.D. of 010 or more b: I.D. chamfering for the bushing I.D. of 010 or more mm) Chamfering of inner or outer diameters less than 010 mm is done only to remove burrs. ^The joint causes no influences upon rotation of the shaft. Be careful when press-fitting so that the joint is not at the position to which the maximum load is applied. ^ Outer diameter is measrued by exclusive...

Technical Product Corporate Profile Information Slide Shifter Air Bearings Metallic Bearing BMBEBBKBBaBalBM Plastic Bearing Information Selection Guide Mating shaft Bushing Housing ^The joint causes no influences upon rotation of the shaft. Be careful when press-fitting so that the joint is not at the position to which the maximum load is applied. ^ Outer diameter is measrued by exclusive gauge. ^The I.D. tolerance after press fitting is for reference only. MD. 05~030 are shown on pages 145 to 146. Product Technical Selection Guide Information Plastic Bearing BMBCuSiCbShBEIbBSBM Metallic Bearing...

Technical Product Corporate Profile Information Slide Shifter Air Bearings Metallic Bearing BMBEBBKBBaBalBM Plastic Bearing Information Selection Guide 70P Oiles Drymet ST Plates 1564 V. How to attach washers, plates ^Sliding surface consists of a plastic layer. ^Sliding surface consists of a plastic layer. ©Using glue In the case of (2), the washer and plate may be inserted with glue, not a knock pin. Synthetic epoxy plastic glue is suitable, though no glue is specified, in particular. Be careful because fitting with glue only may result in separation in some cases. Product Technical Selection...

Polytetrafluoroethylene plastic multi-layer bearings with back metals Test data Journal rotation test Feature • Serviceable without the need for lubrication. Thin and lightweight for compact design. • Demonstrate low coefficient of friction and superior load performances in high-load, low-speed conditions. • Usable at the high PV values even in the middle- and high-speed zones when lubricated. • Usable in wide temperature ranges from low to high temperatures. Has superior chemical resistance. • Features superior dimensional stability, mechanical strength, and thermal conductivity. • The standard...

Selection Guide PTFE multi-layer bearings with back metals Press-fitting (Rolled bushing) Press-fit force Press-fit smoothly with hydralic (pressure), pneumatic pressure, or a vice. Figure 1 The dimension of guide ring should be calculated from table below. Dimension of bushing Guide ring I.D. Up to φ40 ※1 Techmet B Standard Type (TCB) should be Do-(0.25 to 0.30). ※2 Use of flange bushings should be the same size of flange. t ：thickness of the steel backing L ：length of the bushing S ：average interference D1：O.D. of bushing Guide ring I.D.of bushing I.D.of bushing ※LFCF is obtained by below formula....

Technical Product Corporate Profile Information Slide Shifter Air Bearings Metallic Bearing BMBEBBKBBaBalBM Plastic Bearing Information Selection Guide Part No. Mating shaft a: O.D. chamfering for the bushing I.D. of 010 or more b: I.D. chamfering for the bushing I.D. of 010 or more T % Chamfering of inner or outer diameters less than $10 mm is done only to remove burrs. % Outer diameter is measrued by exclusive gauge. %The I.D. tolerance after press fitting is for reference only. %I.D. $30~$160 are shown on pages 157 to 158. Product Technical Selection Guide Information Plastic Bearing BMBCuSiCbShBEIbBSBM...

Technical Product Corporate Profile Information Slide Shifter Air Bearings Metallic Bearing BMBEBBKBBaBalBM Plastic Bearing Information Selection Guide Part No.Mating shaft Housing ^ Outer diameter is measrued by exclusive gauge. ^The I.D. tolerance after press fitting is for reference only. MD. 03~028 are shown on pages 155 to 156. Product Technical Selection Guide Information Plastic Bearing BMBCuSiCbShBEIbBSBM Metallic Bearing Air Bearings Slide Shifter Information Corporate Profile